User Manual for MIBOXER models including: FUT035SA, FUT036SA, Dual White LED Controller Kits, Single Color LED Controller Kits
Controller adopt the widely used 2.4GHz wireless technology with the features of low power consumption, long signal.
Signal transmitting One controller can transmit the signals from the remote control to another controller within 30m, as long as there is a controller within
Subordinate New Brand 36mm Introduction Controller adopt the widely used 2.4GHz wireless technology with the features of low power consumption, long signal transmitting and strong anti-interference, etc. Controller has auto-transmitting function. Widely used on the controlling of hotel lighting and home lighting. 70mm 24mm 74.5mm 17mm Button Diagram Turn on lights / Link / Unlink Brightness Color temp. Turn off lights Dual White LED Controller Kits (Model No.: FUT035SA) Single Color LED Controller Kits (Model No.: FUT036SA) Touch ring: brightness, color temperature, use together. (It turns to adjust brightness by default if remote is not operated for 3 seconds) Dual White LED Controller Kits Model No.: FUT035SA LED Controller Sunrise Remote Working Voltage: DC12V~24V Working Voltage: 3V(AAA*2PCS) Output: 12A/Channel Transmitting Power: 6dBm Total Output: Max 12A Standby Power: 20uA RF: 2.4GHz RF: 2.4GHz Control Distance: 30m Modulation Method: GFSK Working Temperature: -10~40°C Output Connection: Common anode Single Color LED Controller Kits Model No.: FUT036SA LED Controller Working Voltage: DC12V~24V Output: Max 12A RF: 2.4GHz Control Distance: 30m Working Temperature: -10~40°C Output Connection: Common anode Sunrise Remote Working Voltage: 3V(AAA*2PCS) Transmitting Power: 6dBm Standby Power: 20uA RF: 2.4GHz Modulation Method: GFSK Color temperature adjustable Dim brightness 2.4G RF wireless transmission technology Remote control Control distance 30m Smartphone APP control (2.4GHz gateway is needed) Support third party voice control (2.4GHz gateway is needed) Dim brightness 2.4G RF wireless transmission technology Remote control Control distance 30m Smartphone APP control (2.4GHz gateway is needed) Support third party voice control (2.4GHz gateway is needed) V- V+ Input: DC12V/24V V- V+ Input: DC12V/24V OUTPUT WW CW OUTPUT V+ LED V+ CW WW LED V- Install The Battery For Remote Note: 2*AAA Battery need to buy seperately 1. Open battery cover behind remote. 2. Install battery correctly and close battery cover. Remote Instruction Adjust color temperature Short press key once, then touch to adjust color temp Adjust brightness Short press key once, then touch to adjust brightness. Linking Code / Unlinking Code Instructions Attention: No need to match code since its already matched code in factory setting Linking Code Instructions Power Link/Unlink button Power 1 2 3 Switch off controller, after 10 seconds then switch on again. Short press "ON" button 3 times within 3 seconds when light on. Lights blink 3 times slowly means linking is done successfully. Linking failed if light is not blinking slowly, Please follow above steps again.(Note: controller that have linked can't link again) Unlinking Code Instructions Power Link/Unlink button Power Signal transmitting One controller can transmit the signals from the remote control to another controller within 30m, as long as there is a controller within 30m, the remote control distance can be limitless. Signal transmitting Controller Distance 30m Controller PWM high frequency / low frequency switching Switch to high frequency (8KHz): on the condition of turning on the light 1. Short press the "OFF" button of the remote control once; 2. Short press the "ON" button 5 times within 3 seconds, the white light blink 2 times quickly, indicating successfully. Switch to low frequency (500Hz): on the condition of turning off the light 1. Short press the "ON" button of the remote control once; 2. Short press the "OFF" button 5 times within 3 seconds, the white light blink 2 times slowly, indicating successfully. Attention 1. Please check whether the voltage of the power supply is in accordance with the controller, and please check the connection of both the cathode and anode, otherwise the controller will be broken. 2. Please don't connect wires with power on. Please turn on again only when it is in right connection and no short circuit. 3. Please do not use the controller in the place with widely range metal area or strong electromagnetic wave nearby, otherwise, the remote distance will be seriously affected . 1 2 3 Switch off controller, after 10 seconds then switch on again. Short press "ON" button 5 times within 3 seconds when light on. Lights blink 10 times quickly means unlinking is done successfully. Unlinking failed if light is not blinking quickly, Please follow above steps again.(Note: controller haven't linked that don't need to unlink) Made in China Controller can not use in humid areaAdobe PDF library 15.00 Adobe Illustrator CC 22.1 (Windows)