Instruction Manual for STMicroelectronics models including: VL53L7CX Time-Of-Flight Ranging Sensor, VL53L7CX, Time-Of-Flight Ranging Sensor, Flight Ranging Sensor, Ranging Sensor, Sensor
VL53L7CX - Time-of-Flight 8x8 multizone ranging sensor with 90 degrees FoV - STMicroelectronics
File Info : application/pdf, 6 Pages, 520.83KB
DocumentDocumentAN5853
Application note
PCB thermal guidelines for the VL53L7CX TimeofFlight 8x8 multizone ranging sensor with 90° FoV
Introduction
When used in continuous mode, the VL53L7CX module requires careful thermal management to ensure optimum device performance and to avoid overheating.
Table 1. Main thermal parameters
Parameter
Symbol
Min
Power consumption
P
--
Module thermal resistance
mod
--
Junction temperature (3)
TJ
--
Operating temperature range
T
-30
1. AVDD = 2.8 V; IOVDD = 1.8 V typical current consumption. 2. AVDD = 3.3 V; IOVDD = 3.3 V maximum current consumption. 3. To prevent thermal shutdown, the junction temperature must be kept below 110°C.
Typ 216 (1)
40 -- 25
Max 430 (2)
-- 100 70
Unit mW °C/W °C °C
Figure 1. VL53L7CX ranging sensor module
AN5853 - Rev 1 - September 2022 For further information contact your local STMicroelectronics sales office.
www.st.com
AN5853
Thermal design basics
1
Thermal design basics
The symbol is generally used to denote thermal resistance which is a measure of a temperature difference by which an object or material resists a heat flow. For example, when transferring from a hot object (such as silicon junction) to a cool one (such as module backside temperature or ambient air).
The formula for thermal resistance is shown below and is measured in °C/W:
=
T P
Where T is the rise in junction temperature and P is the power dissipation.
So, for example, a device with a thermal resistance of 100 °C/W exhibits a temperature differential of 100°C for a power dissipation of 1 W as measured between two reference points.
If a module is soldered to a PCB or flex then the total system thermal resistance is the sum of the module thermal resistance and the thermal resistance of the PCB or flex to the ambient/air. The formula is as follows:
T = TJ - TA = P × mod + pcb
Where:
· TJ is the junction temperature
· TA is the ambient temperature
· mod is the module thermal resistance
· pcb is the thermal resistance of the PCB or flex
AN5853 - Rev 1
page 2/6
2
Note:
AN5853
Thermal resistance of PCB or flex
Thermal resistance of PCB or flex
The maximum permitted junction temperature of the VL53L7CX is 100°C. So, for a power dissipation of 0.43 W operating at the maximum specified ambient temperature of 70°C (worst case scenario), the maximum permitted PCB or flex thermal resistance is calculated as follows:
· TJ TA = P × (mod + pcb)
· 100 70 = 0.43 × (40 + pcb)
·
pcb =
100 - 70 0.43
- 40
· pcb 30°C/W
This gives a combined system thermal resistance of 70°C/W (mod + pcb).
To ensure the maximum junction temperature is not exceeded and to ensure optimum module performance, it is recommended not to exceed the above target thermal resistance.
For a typical system dissipating 216 mW, the maximum temperature rise is < 20°C which is recommended for optimum performance of the VL53L7CX.
AN5853 - Rev 1
page 3/6
AN5853
Layout and thermal guidelines
3
Layout and thermal guidelines
Use the following guidelines when designing the module PCB or flex:
· Maximize the copper cover on the PCB to increase the thermal conductivity of the board.
· Use the module thermal pad B4 shown in Figure 2. VL53L7CX pin out and thermal pad (see the VL53L7CX datasheet DS18365 for more details) adding as many thermal vias as possible to maximize thermal conductivity into adjacent power planes (refer to Figure 3. Thermal pad and via on the PCB recommendation).
· Use wide tracking for all signals particularly power and ground signals; track and connect into adjacent power planes where possible.
· Add heat sinking to the chassis or frames to distribute heat away from the device.
· Do not place adjacent to other hot components.
· Place the device in a low power state when not in use.
Figure 2. VL53L7CX pin out and thermal pad
Figure 3. Thermal pad and via on the PCB recommendation
AN5853 - Rev 1
page 4/6
Revision history
Date 20-Sep-2022
Table 2. Document revision history
Version 1
Initial release
Changes
AN5853
AN5853 - Rev 1
page 5/6
AN5853
IMPORTANT NOTICE READ CAREFULLY STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST's terms and conditions of sale in place at the time of order acknowledgment. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of purchasers' products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. For additional information about ST trademarks, refer to www.st.com/trademarks. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2022 STMicroelectronics All rights reserved
AN5853 - Rev 1
page 6/6