ITC Warranty & Return Policy
Installation Guide for ITC models including: Reed Horizontal Bend, Reed Bend, Horizontal Bend, Bend, HTLL12KK-LLLWL-04-X
Reed™ Ultra Thin Horizontal Bend Light
Flexible Light Installation Instructions
File Info : application/pdf, 2 Pages, 819.94KB
DocumentDocumentReed Horizontal Bend Part#: HTLL12KK-LLLWL-04-X PARTS/TOOLS NEEDED: INSTALLATION INSTRUCTIONS Flexible Light Mounting Channel (purchased separately) Power Drill (not provided) Butt Splice Connectors (not provided) #4 Flat Head Screws (not provided) Isopropyl Alcohol & Primer 94 (not provided) SAFETY INSTRUCTIONS · Disconnect power before installing, adding or changing any component. · To avoid a hazard to children, account for all parts and destroy all packing materials. · It is recommended that a 5 Amp standard automotive fuse protection be added to the positive (+) input. INSTALLATION CONSIDERATIONS · Do not bend lighting more than necessary. It should only be bent to a 1" radius. Bending to a tight 90° angle could cause damage to the circuit · Only bend the LED ribbon in one natural direction, do not try to bend in an unnatural direction such as twisting. · Make sure surfaces are smooth, clean and free of dust and debris before installing this product. Failure to properly clean the surface may result in loss of adhesion. · Rough surfaces may prevent proper adhesion. If adhesion failure occurs screw-in mounting channels may be used for installation. · Contact ITC sales for more information on mounting channel: 616-396-1355 / sales@itc-us.com · Electrical specifications: 1.42 W/Ft | 0.11 A/Ft 1. Determine the installation location of your tape lighting. Lights can be attached via the adhesive on the back or with a mounting channel. Clean surface with a mixture of 50% water/50% Isopropyl alcohol. Let surface dry. Apply Primer 94 as recommended by 3M*. Failure to follow the surface preparation guidelines will void the warranty. Mounting channels are available as screw mount. Screws should be used every 12". If there is adhesive on the back of the light, remove before installing in the channel. *http://www.3m.com/3M/en_US/bonding-and-assembly-us/resources/full-story/?storyid=b3996cbd-9954-455f-8e72-88e452ca38c0 3030 Corporate Grove Dr. Hudsonville, MI 49426 Phone: 616.396.1355 itc-us.com For warranty information please visit www.itc-us.com/warranty-return-policy DOC #: 710-00125 · Rev B · 04/14/20 Page 1 of 2 2. Wire the light based on the wiring diagrams below. Note: Addressable Reed tape light will require one driver (part #810-00719) for every 5.5A of power used. Multiple light lengths can be wired to one driver. Tape Light Single Color Reed Black (-) Red (+) Fuse Black (-) To 12V DC Power Tape Light RGB Reed Incoming 12V DC Power Red (-) Green (-) Blue (-) Black (+) Red (+) Black (-) RGB Controller sold separately Addressable RGB Controller 12V DC (+) Black (-) Fuse Incoming 12V DC Power Addressable Reed Orange (D)* Red (+) Black (-) 5V Blue (+) Driver Black (-) Input Output Addressable Reed Light *Data line 3. Please review the considerations below to ensure a successful installation. *Flexible light cannot be field cut. Field cutting the light will void the warranty. R11.8" Do not horizontal bend to a radius of less than 11.8" 4" 0.78" Do not axial bend to the height of more than 0.312" within 0.78" segment R0.59" Less than 0.312" Do not bend to a radius of less than 1/2" Axis Do not twist more than 90° over the length of one 24V segment / Two 12V segments Do not bend flexible Do not bend right at light at 90° solder joint Only bend the wire 3030 Corporate Grove Dr. Hudsonville, MI 49426 Phone: 616.396.1355 itc-us.com For warranty information please visit www.itc-us.com/warranty-return-policy DOC #: 710-00125 · Rev B · 04/14/20 Page 2 of 2