1. Ievads
The NICE WAY WM006G is a radio transmitter module designed for controlling up to 6 roller shutters or groups of shutters. It provides open, stop, and close functionality. This module is an integral part of the NICEWAY system, ensuring compatibility with NICE radio receivers and control logics A01/A02 operating at a frequency of 433.92 MHz.
This manual provides essential information for the proper setup, operation, and maintenance of your WM006G control module.
Figure 1: The WM006G module can be integrated into various NICEWAY accessory housings for different applications.
Figure 2: Illustration of the NICEWAY system, demonstrating wireless communication between the WM006G module, a central receiver, and other compatible accessories.
2. Iestatīšana un savienošana pārī
Before operating your WM006G module, it must be correctly set up and paired with your NICE radio receivers. The module is powered by a single CR2032 battery.
2.1 Akumulatora uzstādīšana
- Uzmanīgi atveriet casing of the WM006G module. Refer to the product diagrams for guidance on accessing the battery compartment.
- Insert one CR2032 lithium coin cell battery, ensuring the correct polarity (+/-) as indicated inside the compartment.
- Close the module casing droši.
2.2 Pairing with Receivers
The WM006G module needs to be programmed or paired with each NICE radio receiver it will control. The exact pairing procedure may vary depending on your specific NICE receiver model. Generally, the process involves activating a programming mode on the receiver and then transmitting a signal from the WM006G module.
- Using an Existing Remote: If you have an existing, working NICE remote control, you can often use it to quickly program the new WM006G module. This typically involves pressing a sequence of buttons on the old remote, followed by a button on the new WM006G module. This process may need to be repeated for each individual roller shutter or group.
- Direct Pairing: For new installations or if an existing remote is unavailable, consult the instruction manual for your specific NICE radio receiver (e.g., A01/A02 logic, FLOR, or ONE series receivers) for detailed pairing instructions. This usually involves pressing a programming button on the receiver itself.
Piezīme: Successful pairing is indicated by a specific response from the receiver, such as a motor movement or an LED flash.
3. Operating the WM006G Module
The WM006G module allows control of up to six individual roller shutters or six groups of shutters using its intuitive button layout.
Figure 3: Layout of the WM006G control module, showing the numbered selection buttons and control functions.
3.1 Pamata vadības funkcijas
- Select Shutter/Group: Press the numbered button (1 cauri 6) corresponding to the specific roller shutter or group of shutters you wish to control.
- Open Shutter: Nospiediet pogu Augšup (▲) button to open the selected shutter or group.
- Close Shutter: Nospiediet pogu Lejā (▼) button to close the selected shutter or group.
- Stop Shutter: Nospiediet pogu Stop button to halt the selected shutter or group at any desired position during movement.
4. Apkope
Regular maintenance ensures the longevity and optimal performance of your WM006G module.
4.1. Akumulatora nomaiņa
The WM006G module is powered by one CR2032 lithium coin cell battery. When the module's response becomes inconsistent or it ceases to function, the battery likely needs replacement.
- Open the module casing as described in the "Battery Installation" section.
- Izņemiet veco CR2032 bateriju.
- Insert a new CR2032 battery, observing the correct polarity.
- Aizveriet casing droši.
- Atbrīvošanās: Atbrīvojieties no izlietotajām baterijām atbildīgi saskaņā ar vietējiem noteikumiem.
4.2. Tīrīšana
To clean the module, use a soft, dry cloth. Avoid using abrasive cleaners, solvents, or excessive moisture, as these can damage the electronic components or the casing.
5. Traucējummeklēšana
If you encounter issues with your WM006G module, try the following troubleshooting steps:
- Modulis neatbild:
- Pārbaudiet akumulatoru: Ensure the CR2032 battery is correctly installed and not depleted. Replace it with a new one if necessary.
- Reprogramming/Pairing: If the module loses connection or is a new installation, it may need to be re-paired with your NICE radio receivers. Refer to the "Setup and Pairing" section and your receiver's manual.
- Diapazons: Verify that the module is within the operational range (35-200 meters) of the receiver. Obstructions like thick walls or metal structures can reduce range.
- Traucējumi: Other radio devices operating on similar frequencies (433.92 MHz) might cause interference. Try operating the module away from such devices.
- Shutter Responds Intermittently:
- This could indicate a weak battery. Replace the CR2032 battery.
- Check for potential sources of radio interference.
- Shutter Moves in Wrong Direction:
- This is typically a programming issue with the receiver or motor. Consult your receiver's manual for instructions on reversing motor direction or re-programming limits.
If these steps do not resolve the issue, contact NICE customer support or a qualified technician.
6. Specifikācijas
| Modelis | WM006G |
| Funkcija | Radio transmitter module for 6 roller shutters/groups (Open-Stop-Close) |
| Barošanas avots | 1 x CR2032 litija monētu šūnu akumulators |
| Biežums | 433.92 MHz |
| Diapazons | 35–200 metri (atkarībā no vides) |
| Izmēri (G x P x A) | 40 mm x 40 mm x 10 mm |
| Preces svars | 100 grami |
| Ražotājs | JAUKI |
7. Garantija un atbalsts
Warranty information for the NICE WAY WM006G module is typically provided with your purchase documentation or can be obtained directly from the manufacturer, NICE. Please retain your proof of purchase for warranty claims.
For technical support, further assistance, or to inquire about spare parts, please contact NICE customer service or your authorized dealer. Contact details can usually be found on the manufacturer's official webvietnē vai jūsu produkta iepakojumā.
