Lumens VC-BC701P 4K UHD Box Camera
To download the latest version of Quick Start Guide, multilingual user manual, software, or driver, etc., please visit Lumens http://www.MyLumens.com/support
Copyright Information
- Copyrights © Lumens Digital Optics Inc. All rights reserved.
- Lumens is a trademark that is currently being registered by Lumens Digital Optics Inc.
- Copying, reproducing or transmitting this file is not allowed if a license is not provided by Lumens Digital Optics Inc. unless copying this file is for backup after purchasing this product.
- To keep improving the product, Lumens Digital Optics Inc. hereby reserves the right to make changes to product specifications without prior notice. The information in this file is subject to change without prior notice.
- To fully explain or describe how this product should be used, this manual may refer to names of other products or companies without any intention of infringement.
- Disclaimer of warranties: Lumens Digital Optics Inc. is neither responsible for any possible technological, editorial errors or omissions, nor responsible for any incidental or related damages arising from providing this file, using, or operating this product.
Safety Instructions
Always follow these safety instructions when setting up and using the product:
Operation
- Please use the product in the recommended operating environment.
- Do not place the product in a tilted position.
- Do not place the product on an unstable trolley, stand or table.
- Do not use this product near water or sources of heat.
- Use attachments only as recommended.
- Use the type of power source indicated on the product. If you are not sure of the type of power available, consult your distributor or local electricity company for advice.
- Always take the following precautions when handling the plug. Failure to do so may result in sparks or fire:
- Ensure the plug is free of dust before inserting it into a socket.
- Ensure that the plug is inserted into the socket securely.
- Do not overload wall sockets, extension cords or multi-way plug boards to avoid potential risks.
- Do not block the slots and openings in the case of the product. They provide ventilation and prevent the product from overheating.
- Except as specifically instructed in this User Manual, do not open or remove covers, otherwise it may expose you to dangerous voltages and other hazards. Refer all servicing to licensed service personnel.
- Unplug the product from the wall outlet and refer servicing to licensed service personnel when the following situations happen:
- If the power cords are damaged or frayed.
- If liquid is spilled into the product or the product has been exposed to rain or water.
Installation
- For security considerations, please make sure the standard hanging rack you bought is in line with UL or CE safety approbations and installed by technician personnel approved by agents.
Storage
- Do not place the product where the cord can be stepped on as this may result in fraying or damage to the lead or the plug.
- Never push objects of any kind through cabinet slots. Never allow liquid of any kind to spill into the product.
- Unplug this product during thunderstorms or if it is not going to be used for an extended period.
- Do not place this product or accessories on top of vibrating equipment or heated objects.
Cleaning
- Unplug all the cables before cleaning. Use a damp cloth for cleaning. Do not use liquid or aerosol cleaners.
Remote control (if the accessories are equipped with remote control)
- Using an incorrect battery type in the remote control may result in a breakdown. Follow local instructions on how to dispose of used batteries.
Precautions
Warning: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. If the HD camera will not be used for an extended time, unplug it from the power socket.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IC Warning
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.
EN55032 (CE Radiation) Warning
Operation of this equipment in a residential environment could cause radio interference.
Package Contents
Function Introduction
I/O functions Introduction
| NO. | Item | Function Descriptions |
| 1. | Lens | 30x HD camera lens |
| 2. | Tally indicator light | Display the tally light status of the camera |
| 3. | Network port | Network port. Support routers or hubs (IEEE 802.3 af) with PoE power supply support |
| 4. | HDMI output | The factory output resolution is 4K/30. Please make sure that the connected display device supports 4K resolution |
| 5. | RS232 output | RS232 output port. At most 7 cameras can be connected in a serial connection |
| 6. | RS232 input | RS232 input port. At most 7 cameras can be connected in a serial connection |
| 7. | DC 12 V power connector | AC power supply connecting port |
| 8. | Power indicator light | After power is on, the indicator light will display in red |
| 9. | Audio input | Support Line In / Mic In |
| 10. | Audio output | Support 3.5 mm audio input |
| 11. | Tripod screw holes | The camera is mounted on a (specification) 1/4”, 20 UNC tripod deck or installed on VC-WM11 (optional) |
| 12 | Locating holes | Ø5; depth 2 mm |
| 13 | Reset button | Hold the button to reset the camera settings |
Tally Indicator Light Function Description
The Tally light function may be enabled through the control of the RS232 command. Please refer to the VC-BC701P RS-232 command set document
Instruction for installation
Basic Devices
- VC-BC701P size
Length x Width x Height: 169 x 67.0 x 67.0 mm
Weigh: 0.5 Kg
- Installation method
- Wall-mounted frame: The camera is installed on the wall, using Lumens VC-WM11 (optional) wall-mounted frame.
- Tripod: The camera is mounted on a 1/4”, 20 UNC PTZ tripod deck.
- Wall-mounted frame: The camera is installed on the wall, using Lumens VC-WM11 (optional) wall-mounted frame.
Connecting devices
- HDMI connection to TV/display screen
- Connecting to Internet
<Remark> For details of web page connection setting and description, please refer to Chapter 5 Network Function Settings Description. - Connecting AUDIO IN
- Connecting RS-232
- RS-232 serial connection
With RS-232 in/out, at most 7 Lumens cameras can be connected
- RS-232 serial connection
Network Function Settings Description
Web System Requirements
- Web Browser:
- Internet Explorer 11 or above
- Firefox 66.0.3 or above
- Chrome 73 or above
- Edge 42.17134 or above
- Safari 12.1 or above
Connecting Camera to Network
- Connecting to Internet
Two common connection methods are shown below- Connecting via switch or router
- If the camera is connected to the computer directly, the computer IP address must be modified to have the same network segment as the camera
For example, the factory-preset default IP address of VC-BC701P is 192.168.100.100. The computer IP address must be set with the same subnet, such as 192.168.100.101 so that the computer can be connected correctly with the camera
- Change network settings
- Change network settings
- Connecting via switch or router
Using Lumens VMS Software to View the Images
- The VC-BC701P DHCP initial setting is ON. If VC-BC701P is connected to the local area network (LAN), the camera IP can be retrieved via the following methods
- Install Lumens VMS software (Please download from the Lumens official website, http://www.mylumens.com/support)
- Open LUMENS VMS software
- Search for the camera: Press
[automatically search for the device] button to locate the VC-BC701P camera - Click VC-BC701P in the list and start operation after connecting to the network
<Note> When using automatic search, the camera and computer must be in the same network segment, e.g.: 192.168.4.X
Using the Browser to View the Images
- Open the browser, and enter the URL of VC-BC701P in the IP address bar e.g.: http://192.168.100.100 (default IP address)
- Enter the administrator’s account and password Account: admin (Default) Password: 9999 (Default)
<Remark> For a first-time login, please refer to 5.3.3 Account Management to change the default password.
Using RTSP Player to View the Images
Besides the browser and VMS, other free software also can be used for RTSP connection, such as VLC、Quick Time、PotPlayer and other free software
RTSP connection address formats are as follows:
- RTSP Stream 1 => rtsp://camera IP:8554/hevc
- RTSP Stream 2 => rtsp://camera IP:8557/h264
- RTSP Stream 3=> rtsp://camera IP:8556/h264
If password authentication is enabled, the RTSP connection address is as follows:
- RTSP Stream 1
rtsp://Username: Password@VC IP address: port/hevc - RTSP Sub1/ Sub2 Streaming
rtsp://Username: Password@VC IP address: port/h264 - To enable password authentication function, please refer to 5.3.9 Setting-Network
Example: Open VLC software and input the URL: rtsp://192.168.100.150:8557/h264
Web Page Function Description
- Login Screen
No Item Function Descriptions 1 Username Enter user account name (default: admin) 2 Password Enter user password (default: 9999) <Remark> For a first-time login, please refer to 5.3.3 Account Management to change the default password
3 Language selection Currently, the system supports English, Traditional Chinese and Simplified Chinese 4 Remember password Save user account name and password to the browser. When you login next time, there is no need to re-enter them 5 Login Log into the administrator screen on the website - Viewing In Real Time
No Item Function Descriptions 1 Preset setting Select the number first and then select SAVE or LOAD 2 Zoom ratio Adjust the zoom-in or zoom-out ratio via scroll bar 3 Preview window Display the screen currently captured by the camera 4 Switch to Full Screen Switch the preview window to full screen 5 Power button Turn on or turn off the camera power - Account Management
No Item Function Descriptions 1 Add user account Enter a username and password to add a new user 2 Permission setting Set the new account management permissions 
3 Applying setting Add the newly created user to the account list 4 List of accounts Edit: Modify the user password and permissions Delete: Delete the user account - Setting-System Setting
No Item Function Descriptions 1 Resolution Set the resolution of the camera. Resolutions supported by the camera are as follows: 3840x2160P 60/ 59.94/ 50/ 30/ 29.97/ 25 fps
1080P 60/ 59.94/ 50/ 30/ 29.97/ 25 fps
720P 60/ 59.94/ 50/ 30/ 29.97/ 25 fps
1080i 60/ 59.94/ 50 fps
After switching to the resolution, the camera will restart. Please refresh the browser
2 Output signal According to the output resolution, selections are available for HDMI output, streaming output, or HDMI + streaming output. For output signals supported by different resolution, please refer to the following table: Resolution Available output modes 3840×2160 60/ 59.94/ 50 HDMI or streaming single output 3840×2160 30/ 29.97/ 25 Simultaneous HDMI and streaming outputs 1080p 60/ 59.94/ 50/ 30/ 29.97/ 25 720p 60/ 59.94/ 50/ 30/ 29.97/ 25 1080i 60/ 59.94/ 50 3 HDMI Format Select YUV422, YUV420 or RGB <Remark>YUV420 is only available for these two resolutions, 3840×2160/ 59.94p and 3840×2160/ 50p and remains in display mode for all other resolutions
4 Overlay Set the stream to display “date and time” or “custom content” and to display “location” <Remark>“Custom Content” supports up to 30 characters
- Setting-Video
No Item Function Descriptions 1 Camera ID Modify the camera name n Camera names are limited to 1-12 characters
n Please use a camera name by mixing uppercase and lowercase letters and numbers. Do not use “/” and “space” or special symbols
<Note> Modifying this field will modify the Onvif device name synchronously
2 Location Modify the location of the camera, such as Meeting Room 1 n Camera locations are limited to 1-11 characters
n Please use a camera name by mixing uppercase and lowercase letters and numbers. Do not use “/” and “space” or special symbols
<Note> Modifying this field will modify the Onvif device location synchronously
3 Streaming 1 / Streaming 2 / Streaming 3 VC-BC701P supports 3 streaming outputs. Please refer to 5.3.5.1 Streaming Parameter Setting for relevant settings 4 Open streaming Confirm the streaming function - Streaming parameter setting
Function Streaming 1 Streaming 2 Streaming 3 Encode Format H.265 H.264 Resolution 4K /1080P / 720P 1080P / 720P/ 1080i D1 Frame rate Setting according to the supported resolution <Remark> Only supports 59.94/ 50 when the stream 2’s resolution is 1080i
Bit Rate(kbps) Range 2,000~20,000 2,000~20,000 512~5,000 Factory default 15,000 7,500 1,000 Rate control VBR / CBR IP ratio Setting according to the supported resolution <Remark> Only supports 15 / 25 when the resolution is 1080i
- Streaming parameter setting
- Setting-Camera
No Item Function Descriptions 1 Zoom ratio Adjust the zoom-in or zoom-out ratio via scroll bar 2 Exposure 
n Mode: Select exposure mode (Automatic/Shutter Priority/Aperture Priority/Manual )
n Exposure Comp. Level: Select exposure compensation level
n Gain: The gain limit is adjustable when the exposure mode is set to “Manual”
n Iris: The size of aperture is adjustable when the exposure mode is set to “Manual” or “Aperture Priority”
n WDR: Set the level of wide dynamic range (WDR) in order to obtain better images
n Shutter Speed: The shutter speed is adjustable when the exposure mode is set to “Manual” or “Shutter Priority”
3 White balance 
n Mode: Select the color temperature mode • Auto
• Indoor
• Outdoor
• One Push WB
• ATW
• Manual
• Sodium Lamp
• 3000K/ 4300K/ 5000K/ 6500K/ 8000K
n Open Push Trigger: One push color temperature is adjustable
when the white balance mode is set to “One Push Trigger”
n Manual Red/Blue: Manually adjust blue/red color temperature
4 Focus 
n Mode: Select manual/automatic focus
n Focus Range: The focusing range is adjustable when the focus mode is set to “Manual”
n AF Sensitivity: Set automatic focus sensitivity
n AF Frame: Set automatic focus range
n Zoom Tracking: The focus can be set during lens zooming in
Manual Focus mode
n Smart AF: Turn on this function and AF will mainly focus on the face
n Preset AF: Set whether to perform auto focus after Preset
n One Push AF: When the manual focus mode is on, click the button to perform one auto focus
5 Mirror 
n Mirror: Set automatic flip mode
• Off
• Mirror
• Flip
• Mirror + Flip
6 Tally Light 
n Enable/ Disable Tally Light n Tally CMMD Mode: Set whether the indicator light is linked with RS232 command
• General (Not linked): The indicator light switch and mode shall be set separately.
-When the indicator light is on and the default mode is off, additional command is required to set the indicator light mode
-Setting the indicator light mode when the indicator light is off will not trigger the indicator light
• Link:
-When the indicator light is on, the default mode is red light
-Setting the indicator light mode when the indicator light is off will turn on the indicator light
7 D-Zoom Limit 
Set the D-Zoom Limit, x1-x12
8 IQ Sync 
Set IQ main synchronized device
Available when “Exposure” and “White Balance” is set to “Auto” mode
(Currently it’s the beta version. Please refer to Web Page
Firmware Update Information for the official version release schedule.)
- Setting-Picture
No Item Function Descriptions 1 Picture effect Set picture effect, Off / Film / Black and White 2 2D noise reduction settings 2D noise reduction settings 3 3D noise reduction settings 3D noise reduction settings 4 Image mode The user may customize his/her desired image mode 5 Image mode load When no custom setting is needed, reset the picture parameters back to the factory default by selecting this item 6 Gamma Gamma Level adjustment; Adjustable when the image mode is set to Custom 7 Brightness Brightness adjustment; Adjustable when the image mode is set to Custom 8 Contrast Contrast adjustment; Adjustable when the image mode is set to Custom 9 Saturation Saturation adjustment; Adjustable when the image mode is set to Custom 10 Sharpness Adjust the sharpness of the image - Setting-Audio
No Item Function Descriptions 1 Open audio Turn on / off sound 2 Audio In Type Set MIC In / Line In 3 Audio Volume Adjust Volume 4 Audio Delay Turn on / off Audio Delay 5 Audio Delay Time Set the audio delay time (-1~-500ms) 6 Encode Type AAC / G.711 7 Encode Sample Rate Set Encode sample rate • 48 KHz(AAC)
• 44.1 KHz(AAC)
• 16 KHz(AAC)
• 16 KHz(G.711)
• 8 KHz(G.711)
- Setting-Network
No Item Function Descriptions 1 Network Network setting of camera. Change of setting is available only when DHCP function is closed. 2 RTMP Setting Copy the RTMP web address provided by the RTMP service platform and paste it to the RTMP connection address to publish the camera images on the RTMP service platform <Remark>To upload to YouTube for live streaming, please see 5.3.8 Setting – Audio to turn on the audio function first
3 RTSP Setting n Enable/Disable Multicast. It is suggested to enable Multicast when the number of users online watching the live image simultaneously is more than 4
n Enable/Disable Password Authentication
• RTSP connection format can be found in 5.2.4 Using RTSP Player to View the Images
• The username/password is the same as the web login password of the camera, please refer to 5.3.3 Account Management to
add/modify account information
4 MPEG-TS Setting The port number must be set in the range above 1024 with a maximum value of 9999 <Remark> The following port has been used by the camera. Setting of the port may not connect correctly
8554, 8556, 8557, 8080, 9090, 1935
5 SRT Setting 1. Set the field of SRT and then check the item to open SRT streaming After the SRT streaming is opened, it will be connected automatically upon startup 2. The port number must be set in the range above 1024 with a maximum value of 9999
The following port number has been used by the camera. Setting of the port number may not connect correctly
8554/ 8557/ 8556/ 8555/ 1935
3. Delay time is for 20 to 8,000 microseconds. The default value is 120 microseconds
6 SNTP / Port Setting n SNTP Setting: Set SNTP Server IP n Port Setting: Set HTTP port. The default Port value is 80 Port Setting: Set HTTP port. The default Port value is 81
<Remark> Change of setting is available only when DHCP function of camera is closed
- Setting-Time
No Item Function Descriptions 1 Camera Time Display the date and time of the camera 2 Set the Time n Set Manually: Set time manually n Synchronize with computer time: Set the camera time according to the computer time
n Synchronize with SNTP server: Set the camera time synchronously with the SNTP server
<Remark> SNTP server address: Please change in network setting
- Setting-Maintenance – Upgrading Firmware
No Item Function Descriptions 1 Firmware Update The camera firmware may be upgraded via web page. For the upgrade method, please download the FW upgrade manual from Lumens website - Setting-Maintenance – Incident Log
No Item Function Descriptions 1 Event Logs If the camera encounters errors, an error code log will be established <Remark> When an error code appears, the user may try to clear and confirm if the error will repeat itself
- Setting-Maintenance – Security
No Item Function Descriptions 1 802.1x Setting Enable/ disable 802.1x protocol, and configure settings when enabled <Remark> The router must support 802.1x protocol to enable
this feature
- Setting-Maintenance – System Service
No Item Function Descriptions 1 Reset to the default value Select the reset button to resume the factory default setting as the web page setting 2 Setting File The web page setting parameters can be exported from the computer and imported/applied to another camera 3 Communication protocol related settings
Communication protocol related settings for the use of connecting RS-232/ RS-422 communication - Setting-Maintenance – Reboot
No Item Function Descriptions 1 Reboot Reboot immediately 2 Disable Disable the reboot settings 3 Daily Reboot Set the daily reboot time <Remark> Please go to Setting – Time to complete the SNTP server synchronization to set daily reboot
4 Timing Reboot Set the timing reboot time - About
No Item Function Descriptions 1 Camera ID Display the camera name 2 Firmware Version Display the firmware version of the camera 3 Detail Information Display firmware version-related information 4 Serial Number Display the camera serial No. 5 Uptime Displaying the running time of the camera (the timing of standby continues; the time will be reset when the camera is rebooted or turned off)
Troubleshooting
This chapter describes problems you may encounter while using VC-BC701P. If you have questions, please refer to related chapters and follow all the suggested solutions. If the problem still occurred, please contact your distributor or the service center.
| No. | Problems | Solutions |
|
1. |
Boot without power signal | 1. Make sure you have plugged in the power cord.
2. When using a PoE connection, ensure that the power supply supports IEEE 802.3af hubs |
| 2. | There is no image output from VC-BC701P | 1. Check the power supply or PoE supply functions.
2. Confirm the output signals are in streaming output. 3. If the camera is connected to a monitor, confirm the monitor equipment supports 4K output 4. Replace the cables and make sure they are not faulty. |
|
3. |
VC-BC701P image is severely delayed | Please use 4K, 1080p or 720p 60/50 Hz signals rather than 25/30 Hz signals. |
|
4. |
RS-232 cannot be controlled | 1. Confirm the connection is correct (RS-232 Input / Output)
2. Please make sure the Baud rate setting is the same as the control equipment |
|
5. |
Whether the Internet can be used for operation | Please refer to Chapter 5 Network Function Description for the Internet usage |
|
6 |
The ONVIF software cannot find the machine |
Please go to Setting – Video – Camera Location in the webpage and make sure that the ID is only made up of English letters or numbers. The ONVIF software cannot find the machine if you use
special characters and space. |
|
7 |
Tally light is not working when applying RS232
setting |
Please go to Setting – Camera – Tally Light in the webpage to check if the function is on. |
Supplier’s Declaration of Conformity 47 CFR § 2.1077 Compliance Information
- Manufacturer: Lumens Digital Optics Inc.
- Product Name: VC-BC701P
- Model Number: UHD Box Camera
Responsible Party – U.S. Contact Information
- Supplier: Lumens Integration, Inc. 4116 Clipper Court, Fremont, CA 94538, United States
- e-mail: support@mylumens.com
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Documents / Resources
 |
Lumens VC-BC701P 4K UHD Box Camera [pdf] User Manual VCAX105, VC-BC701P, VC-BC701P 4K UHD Box Camera, 4K UHD Box Camera, UHD Box Camera, Box Camera, Camera |