T10 Smart Wi-Fi Camera
“
Product Information
Specifications
- Product Name: Smart Wi-Fi Camera T10
- Exterior Features: Lens, Light Sensor, LED, MIC
- Connection Methods: One Click Connection, Scan the QR code
- Functionality: Dual Lens Zoom, Voice Call, Video Call, Motion
Detection, Pan & Tilt Control
Product Usage Instructions
Connection Method – One Click Connection
- Find the device ID and click on ‘Connect’.
- Click +Add, the page jumps to figure 2.
- Find the device ID again and click on ‘Connect’.
- Select WiFi, enter the correct password, and click Next.
- Wait for the connection to establish.
Connection Method – Scan the QR Code
- Click + to add the device.
- Scan the QR code on the camera label.
- Upon hearing a sound or seeing the indicator light flashing,
check and click Next. - Select WiFi, enter the correct password, and click Next.
- Align the QR code with the camera and proceed.
- Customize the device name by clicking on the input box and then
click Get started.
Calling Interface and Function Settings
In the calling interface and function settings, you can:
- Make voice and video calls.
- Hang up calls and switch camera views.
- Enable motion detection and human frame recognition.
- Control pan & tilt movements – slide up, down, left,
right. - Add frequent viewing positions for quick access.
This device complies with part 15 of the FCC Rules. Operation is
subject to specific conditions to avoid interference and maintain
proper functionality. Any unauthorized modifications may void the
user’s authority to operate the equipment.
FAQ
Q: How can I reset the camera to its factory settings?
A: To reset the camera, locate the reset button or follow the
instructions in the user manual for a step-by-step guide on
resetting to factory settings.
Q: Can I use the camera outdoors?
A: This camera is designed for indoor use. Using it outdoors may
affect its performance and durability.
“`
Smart Wi-Fi Camera
T10 User Manual
Exterior
Lens Light Seser
LED MIC
Cilick to call
Connection method-One Click Connection
1Find the device ID and click on ‘Connect’ 2Click “+Add,” the page jumps to figure 2.
2-1Find the device ID and click on ‘Connect’
3Select WiFi, enter the correct password, and click “Next.”
4Waiting for connection.
Connection method–Scan the QR code
1Click “+” to add device.
2Scan the QR code on the camera label.
3Upon hearing a sound or seeing the indicator light flashing, check and click “Next.”
4Select WiFi, enter the correct password, and click “Next.”
05
06
07
08
5Align the QR code with the camera.
6Click on the input box, customize the device name, and click “Get started.”
Calling interface
Function settings
User’s camera
Dual lens zoom
Voice call Video call
Click to hang up Switch camera
Motion detection
Human frame
Pan&tilt control Slideup, down, left, right
Dual lens zoom
Add frequent viewing position
09
10
11
12
13
13
14
15
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. -This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Documents / Resources
 |
LUMAISLE T10 Smart Wi-Fi Camera [pdf] User Manual 2BRTW-T10, 2BRTWT10, T10 Smart Wi-Fi Camera, T10, Smart Wi-Fi Camera, Wi-Fi Camera, Camera |