CRAFTSMAN 10" Radial Arm Saw Model 113.23100 Owner's Instructions and Parts Manual

Įvadas

This manual provides detailed instructions for the safe and efficient operation, setup, adjustment, and maintenance of your CRAFTSMAN 10-inch Radial Arm Saw, Model 113.23100. Please read this manual thoroughly before operating the saw to ensure proper use and to prevent injury or damage to the tool. Keep this manual accessible for future reference.

Image 1.1: Cover of the official CRAFTSMAN 10-inch Radial Arm Saw Model 113.23100 Owner's Manual.

Saugos informacija

Always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury. This section outlines critical safety guidelines specific to radial arm saw operation.

• Dėvėkite akių apsaugą: Visada dėvėkite apsauginius akinius arba veido kaukę.
• Laikykite apsaugas vietoje: Ensure all safety guards are properly installed and functioning.
• Atjunkite maitinimą: Prieš atlikdami techninę priežiūrą, reguliavimą ar peilių keitimą, atjunkite pjūklą nuo elektros tinklo.
• Maintain a Clear Work Area: Laikykite darbo vietą švarią, gerai apšviestą ir be netvarkos.
• Use Proper Support: Always support long workpieces to prevent tipping.

Sąranka

Proper setup is crucial for the safe and accurate operation of your radial arm saw. Follow these steps carefully.

Išpakavimas ir surinkimas

1. Atsargiai išimkite visus komponentus iš pakuotės.
2. Patikrinkite, ar visos dalys yra pakuotės sąraše.
3. Assemble the stand (if applicable) according to the provided diagrams.
4. Mount the saw unit securely to the stand or workbench.

Elektrinis sujungimas

Ensure the saw is connected to a grounded electrical outlet of the correct voltage ir amperage. Refer to the saw's motor plate for specific requirements.

Aligning the Saw to the Table

Accurate alignment is essential for precise cuts. This procedure should be performed periodically and after any significant movement of the saw.

1. Check for Squareness: Use a reliable square to check the blade's perpendicularity to the fence. Adjust if necessary using the appropriate adjustment bolts.
2. Table Leveling: Ensure the saw table is level and flat. Shims may be required under the table supports.
3. Arm Parallelism: Verify the radial arm is parallel to the table surface. Adjust the arm support bolts as needed.

Image 4.1: Illustration of blade and table alignment points.

Naudojimo instrukcijos

This section covers the basic operation of your CRAFTSMAN radial arm saw for various cutting tasks.

Skersinis

1. Position the workpiece firmly against the fence.
2. Lower the blade to the desired depth.
3. Paleiskite pjūklą ir leiskite ašmeniui pasiekti visą greitį.
4. Slowly pull the saw carriage forward through the workpiece.
5. Return the saw carriage to the rear position before turning off the motor.

Pjovimas

Note: Rip cutting with a radial arm saw requires extreme caution. Always use the anti-kickback fingers and blade guard.

1. Rotate the motor and blade assembly to the rip position.
2. Nustatykite išilginio pjovimo kreiptuvą iki norimo pločio.
3. Adjust the blade height to just clear the workpiece.
4. Lėtai ir tolygiai stumkite ruošinį į diską.

Koregavimai

Regular adjustments ensure the saw operates at peak performance and accuracy.

• Blade Depth Adjustment: Use the depth crank to set the desired cutting depth.
• Nuožulnumo kampo reguliavimas: Loosen the bevel lock and tilt the motor to the desired angle.
• Įstrižo kampo reguliavimas: Release the miter lock and pivot the arm to the required angle.

Tepimas

Proper lubrication extends the life of your saw and ensures smooth operation. Refer to the lubrication points diagram.

• Variklio guoliai: Apply a few drops of light machine oil to motor bearings every 50 hours of operation.
• Carriage Rails: Keep carriage rails clean and apply a thin coat of dry lubricant or wax.
• Sukimosi taškai: Lubricate all pivot points with a general-purpose grease annually.

Image 7.1: Key lubrication points for the radial arm saw.

Priežiūra

Regular maintenance is vital for safety and longevity.

• Ašmenų keitimas: Always use the correct size and type of blade. Disconnect power before changing blades.
• Valymas: Keep the saw free of sawdust and debris. Use compressed air for hard-to-reach areas.
• Diržo įtempimas: Check drive belt tension periodically and adjust if necessary.
• Electrical Cord Inspection: Prieš kiekvieną naudojimą patikrinkite, ar maitinimo laidas nepažeistas.

Trikčių šalinimas

Šiame skyriuje pateikiami dažniausiai pasitaikančių eksploatavimo problemų sprendimai.

Dalių sąrašas ir sprogimas View Diagramos

This section contains detailed exploded view diagrams and a comprehensive parts list for the CRAFTSMAN 10-inch Radial Arm Saw Model 113.23100. Use these diagrams to identify specific components for replacement or repair.

10.1 paveikslas: Išsklaidytas view of the main saw assembly.

Key Components (Partial List Example)

• Part 1: Motor Assembly
• Part 2: Blade Guard
• Part 3: Radial Arm
• Part 4: Saw Table
• Part 5: Carriage Assembly

For a complete list of parts and their corresponding numbers, please refer to the full manual.

Specifikacijos

Technical specifications for the CRAFTSMAN 10-inch Radial Arm Saw Model 113.23100.

• Modelio numeris: 113.23100
• Ašmenų skersmuo: 10 colių
• Variklis: [Specific Motor Details, e.g., 1.5 HP, 120V, 60Hz]
• Crosscut Capacity: [Specific Measurement, e.g., 16 inches]
• Pjovimo pajėgumas: [Specific Measurement, e.g., 24 inches]
• Language (Manual): anglų kalba
• Number of Pages (Manual): 34

Note: Specific motor and capacity details are typical for this model but should be verified against your saw's nameplate.

Garantija ir palaikymas

This manual is a reproduction of the original CRAFTSMAN owner's and parts manual. For warranty information regarding your CRAFTSMAN 10-inch Radial Arm Saw Model 113.23100, please refer to the original purchase documentation or contact CRAFTSMAN customer support directly. This reproduction manual itself does not carry a separate warranty from the original manufacturer.

For technical assistance or to order replacement parts, please consult the contact information provided in your original saw documentation or visit the official CRAFTSMAN websvetainę.