LOREX E893AB Wired Bullet Security Camera with Smart

Safety Precautions

• Follow all instructions for safe use and handling of the product.
• Use the camera within given temperature, humidity and voltage levels noted in the camera specifications.
• Do not disassemble the camera.
• Do not point the camera directly at the sun or a source of intense light.
• Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh, chemical-based cleaners.
• The supplied cable is rated for surface mounting only (Non-UL). Cables for in-wall and floor-to-floor installations are sold separately (CMR type). These and other cables are available at lorex.com.
• It is recommended to connect the camera to the NVR or an external PoE switch. If using a power adapter with this camera, a REGULATED power supply is REQUIRED (not included). Use of a non-regulated, non-conforming power supply can damage this product and voids the warranty.

Disclaimers

• Use the camera only with compatible Lorex recorders. For a full list, visit lorex.com/compatibility.
• Not intended for submersion in water. Installation in a sheltered location recommended.
• This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/Night viewing modes, an audible clicking noise may be heard from the camera. This clicking is normal, and indicates that the camera filter is working.
• Audio recording and/or face recording without consent is illegal in certain jurisdictions. Lorex Corporation assumes no liability for use of its products that does not conform with local laws.

Package Contents

• 4K IP Smart Deterrence Bullet Security Camera
  
• Mounting Kit*
  
• Ethernet Extension Cable with Pre-attached Weather-resistant Cap*
  

* Per camera in multi-camera packs.

Overview

1. Cable Notch
2. Adjustment Screw
3. Speaker and Siren
4. MicroSD Card Slot
5. Reset Button
   
6. Warning Lights
7. Microphone
   

Camera Placement Tips

• Install the camera in a location that is difficult for thieves and vandals to reach.
• Secure cabling so that it is not exposed or easily cut.
• Point the camera where there is the least amount of obstructions (i.e. tree branches).
• Take into consideration what you want to monitor and where is the best coverage area.
• Place your camera close to the area of interest. The best position is 10ft/3m above ground, angled 15° down.

Mounting Your Camera

Test your cameras prior to selecting a permanent mounting location.

1. Use the included mounting template to drill holes for screws. Insert the included drywall anchors.
2. Feed the cable through the mounting surface or your camera’s cable notch, and then connect the cables as shown in “Connecting Your Camera”, pages 9-10.
3. Mount the camera stand to the surface using the included screws.
4. Loosen the adjustment screw and adjust your camera’s position as needed, and then tighten to secure it in place.
5. Remove the vinyl film from your camera lens when your installation is complete.

Connecting Your Camera

Option 1

Connect your wired camera: Connect your camera directly to your recorder’s camera connection (PoE) using the Ethernet extension cable.

Option 2

Connect your wired camera: Connect your camera to a PoE switch on your network using the Ethernet extension cable. Ensure your switch is connected to the same network as your recorder.

Weather-resistant Cap

The pre-attached weather-resistant cap covers both the camera’s Ethernet connector and the Ethernet extension plug to provide protection from weather, dust, dirt and other environmental contaminants. If exposed to regular precipitation, seal the cap with silicone and electrical tape for additional sealing.

To use the weather-resistant cap: Twist the cap securely onto your camera’s Ethernet connector.

Camera Cable Options

Cable Type	Max. Cable Run Distance	Max. Cable Coupler
CAT5e (or higher) Ethernet Cable	300ft (91m)	3

For different UL CMR approved cable lengths, visit lorex.com and search for the specified cable type in the table.

Need Help?

Download product guides and find related support, scan or visit:

help.lorex.com/E893AB

Register Your Product

Please see our full Terms of Service and Limited Hardware Warranty Policy at: lorex.com/warranty

Copyright © 2023 Lorex Technology Inc.
As our products are subject to continuous improvement, Lorex reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved.

CUSTOMERS SUPPORT

lorex.com
help.lorex.com/E893AB

Documents / Resources

LOREX E893AB Wired Bullet Security Camera with Smart [pdf] User Guide H13, E893AB, E893AB Wired Bullet Security Camera with Smart, E893AB, Wired Bullet Security Camera with Smart, Security Camera with Smart, Camera with Smart, Smart

References

• User Manual