Logitech Rally Camera User Guide
Logitech Rally Camera User Guide
WHAT’S IN THE BOX
- Camera
- Camera Mount
- Power Splitter Case
- Remote
- Power Splitter
- Power Adapter
- USB Cable
- Documentation
WHAT’S WHAT
CAMERA
- Remote Pairing Button
- USB
- Status LED
- Security Slot
- MIPI
- Tripod Thread
- Expansion Slot
REMOTE
- Video Mute
- Pan/Tilt
- Camera Home
- Camera Presets
- Zoom In/Out
CONNECT YOUR CAMERA
Connecting Rally Camera is the same whether you plan on using a dedicated computer in the room, or your team members bring a laptop to the room to run the meeting.
- Plug the power splitter USB pigtail into the USB port of the camera.
- Connect the power adapter from the power splitter to a wall outlet.
- Connect the USB cable from the power splitter to your computer.
- The status LED will flash when the camera is connecting.
Once complete, the camera head will rotate.
- If issues persist, consult www.logitech.com/support/rallycamera or call technical support.
MOUNT YOUR CAMERA
We offer a numer of options to mount your Rally Camera. For video calls, we recommend placing the camera as close to eye level as possible. Best results typically come from mounting below the TV.
- Place on a table or shelf near the TV.
- Mount on the wall:
a. Attach wall mount to the wall.
Please use the appropriate screw type for your wall type.
b. Insert the power splitter into the power splitter case and route cables as shown.
c. Thread the USB pigtail through the hole in the bottom of the mount and connect to the camera.
d. Latch the power splitter case to the mount.
e. Secure the camera to the mount via the tripod screw. - Mount to the TV: An optional TV mount bracket is available at www.logitech.com.
STARTING THE VIDEO CALL
To start a video call/capture session, start your application of choice and select the Rally Camera. The status LED will illuminate when video is streamed.
PAN AND TILT
Press once for incremental movement or press and hold for continuous pan and tilt.
Caution: Manually rotating camera head may damage the device.
CAMERA PRESETS
Set up to 2 preset positions. Once in the desired position, save a preset by pressing and holding the button for 3 seconds.
Return to the desired position at any time by pressing the button once
HOME
Home will be the position the camera moves to when the camera is started. Save a new Home position by holding the button for 10 seconds.
CAMERA SETTINGS
APPLICATION
Use this program to control the camera pan, tilt, zoom, focus, and image quality (like brightness and contrast).
The software can be downloaded from www.logitech.com/support/rallycamera
RIGHTSIGHT
RightSight automatically moves the camera and adjusts the zoom to comfortably frame meeting participants.
RightSight is available on Windows 10 and macOS 10.14+. To enable or disable RightSight, download the Logitech Sync application. Pressing the pan, tilt or zoom buttons on the remote will disable RightSight. Pressing the home button will restart RightSight.
PAIRING THE REMOTE
Your camera and remote control are paired at the factory. However, if you need to pair a remote to the camera (such as when replacing a lost remote) do the following:
- Press and hold button on the back of the camera until LED flashes blue.
- Press and hold the Video Mute button on the remote for 10 seconds to place it in pairing mode.
- Once the remote and camera are paired the LED will stop flashing
- If the pairing fails, the LED will keep flashing. Start from step 2 and repeat.
FOR MORE INFORMATION
You can find additional information on Rally including:
- FAQs
- Firmware Upgrades
- Software Downloads
- Support Community
- Warranty Information
- Replacement Parts
- And more at www.logitech.com/support/rallycamera
FAQs
The pan range is 90 degrees with a 90 degree field of view
It does not.
They make a Logitech Strong cable in 10M and longer. We have had good success in multiple uses.
Yes, it comes with a wall mount
Yes, this camera can be mounted on any standard tripod. The one I purchased also came with a wall mount.
USB directly to the computer.
Yes it does.
It appears like the rally cam is just a component of the rally plus system.
No, the Rally is designed to connect to a computer for recording. It does not record internally.
Yes, a camera mount is included. Along with all of the mounting hardware.
The camera bracket provides flexibility to mount the camera on a wall directly above or below the display for a natural line of sight and eye contact with remote participants. For larger meeting spaces, the bracket can be inverted to position the camera near the ceiling for a more expansive view.
VIDEO
Documents / Resources
 | Rally Camera |
References
- Logitech Support + Downloadsupport.logitech.com
- Product Compliance Certification Search | Logitechwww.logitech.com
- User Manualmanual.tools
Is the sync software on the device absolutely necessary for the Right-Sense technology?
Ist für die Right-Sense Technologie die Sync Software am Gerät zwingend notwendig?
Ist für die Right-Sense Technologie die Sync Software am Gerät zwingend notwendig?
Is the Logitech Sync software required for RightSense technology to function on the Rally Camera?
Yes, for the RightSight component of RightSense technology, the Logitech Sync application is required to enable or disable the feature. RightSight is the automation technology that moves the camera and adjusts the zoom to frame meeting participants automatically.
According to the Logitech Rally Camera manual:
Other RightSense features like RightLight (which optimizes light balance and color) typically function automatically to improve image quality without additional software, though the Camera Settings Application can be used for manual adjustments to brightness and contrast.
Read the full Q&A page
How can I reprogram/change the 2 camera preset buttons on the remote? We use the Rally Camera with both hubs and the whole system, but the two camera preset buttons just seem impossible to reset/update! Without being able to change the presets, those buttons are useless!
How do I reprogram or change the camera preset buttons on the Logitech Rally Camera remote?
To reprogram or change the two camera preset buttons on your Logitech Rally Camera remote, follow these steps:
Additionally, if you wish to change the Home position (the default position the camera moves to when started), move the camera to the desired spot and press and hold the Home button for 10 seconds.
Note: If you are using RightSight automation, manual adjustments or pressing a preset button will temporarily disable RightSight. Pressing the Home button will restart RightSight.
Read the full Q&A page