Check the device label
- Username
- admin
- Password / access
- Password on the device label
Access: Web
ARRIS NVG448, Vantiva EGA228B
Source (opens in a new tab)ROUTER & MODEM REFERENCE
SaskTel router & modem login
Login addresses, default credentials, and setup instructions for SaskTel equipment.
Open router login http://172.16.1.254 (opens in a new tab)Open router login http://192.168.0.1 (opens in a new tab)Open router login http://192.168.1.1 (opens in a new tab)
Connect to the router’s Wi-Fi or Ethernet first. These links open a new tab on your device; the address may differ if the network was reconfigured.
QUICK START
Most likely login options
Start with the option that matches your model. Defaults apply to the factory state; use the password you chose if the device has already been set up.
Options are ordered by manufacturer documentation and coverage among the listed models. Hardware, firmware, and ISP versions can differ.
MODEL DETAILS
Login addresses & credentials
Passwords are case-sensitive. “Leave blank” means an empty field; “Not specified” means the source does not provide that detail. Entries without a model are brand-level references.
| Model / device | Login address | Username | Password / access | Notes & source |
|---|---|---|---|---|
| SaskTelARRIS NVG448Modem / gateway · Web | http://172.16.1.254 (opens in a new tab) | admin | Password on the device label | SaskTel-issued ARRIS gateway, distinct from Ziply Fiber's NVG448BQ already covered (different ISP, different SKU suffix). Username defaults to admin; password is unique per unit from the bottom label. Recovery & reset instructionsSaskTel infiNET fibre gateway (ARRIS NVG448, not the -BQ variant). A factory reset restores the same Device Access Code printed on a label on the bottom of the unit. |
| SaskTelGreen Packet Gateway (fusion Internet)Modem / gateway · Web | http://192.168.0.1 (opens in a new tab) | admin | admin | SaskTel fusion Internet gateway — genuine shared static default admin/admin explicitly documented by SaskTel support, unlike the label-unique fibre gateways above. Recovery & reset instructionsSaskTel fusion Internet fixed-wireless gateway (Green Packet). A reset via the recessed button restores the documented static admin/admin pair; change it under Settings > Management > Password Setting. |
| SaskTelHuawei B2268HModem / gateway · Web | http://192.168.1.1 (opens in a new tab) | admin | LTEcpe | SaskTel Huawei fusion Internet gateway with its own vendor-specific static default (LTEcpe), distinct from the Green Packet gateway's admin/admin above. Recovery & reset instructionsSaskTel fusion Internet fixed-wireless gateway (Huawei B2268H, also reachable at 172.16.1.254). The reset button restores the documented static admin/LTEcpe pair; you're prompted to set a new password on first login. |
| SaskTelVantiva EGA228BModem / gateway · Web | http://172.16.1.254 (opens in a new tab) | admin | Password on the device label | SaskTel-issued fibre gateway. Username auto-fills as admin; password is device-unique, taken from the serial-number label, distinct from SaskTel's other fusion Internet fixed-wireless gateways below. Recovery & reset instructionsSaskTel infiNET fibre gateway (Vantiva/Technicolor EGA228B). A factory reset restores the same unique Web UI Password / 20-character Device Access Code printed on the gateway's serial-number label — it does not reveal a shared admin/admin. |
No records match these filters. Try another model or clear the filters.
Related login addresses
GET CONNECTED
How to reach your router
- Connect your computer or phone to the router’s Wi-Fi or an Ethernet port.
- Open a documented login address. If it does not load, look for the Router or Default gateway address in your device’s network settings.
- Match your model and hardware revision to the table. Use the device label or your setup password when the model has no shared default.
Admin password or Wi-Fi password?
The admin password opens the router’s settings. The Wi-Fi password connects a device to the wireless network. They may be different, and an ISP or cloud account can be separate again.
If the password does not work
Check capitalization and the device label, then use the manufacturer’s password-recovery instructions. A factory reset erases settings and may require ISP setup details; follow the instructions for your exact model.
Find your model’s manual →Sources & data
Router default-credential data from ssid.ai (Drumworks Ventures FZ), licensed CC BY 4.0. Adapted, organized and supplemented by Manuals+. The data is provided as is; manufacturers and ISPs can change defaults.
Additional factual entries: Austin Songer’s credential list and Clint Milner’s credential list. Each table entry links to its supporting source. Updated 2026-10-16.