Use your setup password
- Username
- No username required
- Password / access
- Password created during setup
Access: Web
RG-EW1200G PRO, RG-M32
Source (opens in a new tab)ROUTER & MODEM REFERENCE
Reyee router & modem login
Login addresses, default credentials, and setup instructions for Reyee equipment.
Open router login http://192.168.110.1 (opens in a new tab)Open router login http://ruiyi.cn (opens in a new tab)
Connect to the router’s Wi-Fi or Ethernet first. These links open a new tab on your device; the address may differ if the network was reconfigured.
QUICK START
Most likely login options
Start with the option that matches your model. Defaults apply to the factory state; use the password you chose if the device has already been set up.
Options are ordered by manufacturer documentation and coverage among the listed models. Hardware, firmware, and ISP versions can differ.
MODEL DETAILS
Login addresses & credentials
Passwords are case-sensitive. “Leave blank” means an empty field; “Not specified” means the source does not provide that detail. Entries without a model are brand-level references.
| Model / device | Login address | Username | Password / access | Notes & source |
|---|---|---|---|---|
| ReyeeRG-EW1200G PRORouter · Web | http://ruiyi.cn (opens in a new tab)http://192.168.110.1 (opens in a new tab) | No username required | Password created during setup | Listed as Reyee (Ruijie). No admin/admin. The Reyee EW series ships with no preset admin password - on first login at 192.168.110.1 / ruiyi.cn you configure directly and set your own management password. Recovery & reset instructionsReset: with the router powered on, press and hold the RESET button for about 10 seconds until the system LED blinks, then release and wait for reboot. Browse to http://192.168.110.1 or ruiyi.cn and set a new management password during the wizard. |
| ReyeeRG-EW3200GX PRORouter · Web | http://192.168.110.1 (opens in a new tab) | No username required | Password on the device label | Listed as Ruijie Reyee. Wi-Fi 6 (802.11ax) 3200M dual-band gigabit mesh router (2402 Mbps 5GHz + 800 Mbps 2.4GHz), 5 gigabit Ethernet ports, 8 external antennas; managed via ReyeeOS eWeb or the Reyee Router app. No universal default — the per-device password is on the bottom nameplate (if none is shown, admin is used), and the setup wizard mandates a reset on first login. Corrects the common aggregator claim of admin/admin. Recovery & reset instructionsHold the Reset button for more than 10 seconds to restore factory settings; then log in at http://192.168.110.1 with the per-unit default password printed on the bottom nameplate (format Rexxxxxx). The wizard forces a new eWeb password on first login. |
| ReyeeRG-M32Mesh system · Web | http://192.168.110.1 (opens in a new tab) | No username required | Password created during setup | Listed as Ruijie Reyee. Reyee mesh Wi-Fi router — distinct mesh-category hardware from the already-covered RG-EW1200G/RG-EW3200GX PRO single routers. No preset admin/password pair: first connection to 192.168.110.1 auto-loads the configuration wizard where the owner creates the management password. Recovery & reset instructionsWi-Fi 6 mesh router (ReyeeOS). Hold the Reset pinhole for about 10 seconds until all LEDs flash, then reconnect to the default @Ruijie-sXXXX SSID and run the setup wizard again to create a new management password. |
No records match these filters. Try another model or clear the filters.
Related login addresses
GET CONNECTED
How to reach your router
- Connect your computer or phone to the router’s Wi-Fi or an Ethernet port.
- Open a documented login address. If it does not load, look for the Router or Default gateway address in your device’s network settings.
- Match your model and hardware revision to the table. Use the device label or your setup password when the model has no shared default.
Admin password or Wi-Fi password?
The admin password opens the router’s settings. The Wi-Fi password connects a device to the wireless network. They may be different, and an ISP or cloud account can be separate again.
If the password does not work
Check capitalization and the device label, then use the manufacturer’s password-recovery instructions. A factory reset erases settings and may require ISP setup details; follow the instructions for your exact model.
Find your model’s manual →Sources & data
Router default-credential data from ssid.ai (Drumworks Ventures FZ), licensed CC BY 4.0. Adapted, organized and supplemented by Manuals+. The data is provided as is; manufacturers and ISPs can change defaults.
Additional factual entries: Austin Songer’s credential list and Clint Milner’s credential list. Each table entry links to its supporting source. Updated 2026-10-16.