ROUTER & MODEM REFERENCE

Peplink router & modem login

Connect to the router’s Wi-Fi or Ethernet first. These links open a new tab on your device; the address may differ if the network was reconfigured.

QUICK START

Most likely login options

See every listed combination ↓

Start with the option that matches your model. Defaults apply to the factory state; use the password you chose if the device has already been set up.

Default credentials

Username: admin
Password / access: admin

Access: Web

Balance 20X, Balance 310X, Balance 380 and other listed models

Source (opens in a new tab)

Options are ordered by manufacturer documentation and coverage among the listed models. Hardware, firmware, and ISP versions can differ.

MODEL DETAILS

Login addresses & credentials

10 records

Passwords are case-sensitive. “Leave blank” means an empty field; “Not specified” means the source does not provide that detail. Entries without a model are brand-level references.

Models, login addresses, credentials, instructions and sources
Model / device	Login address	Username	Password / access	Notes & source
PeplinkBalance 20XRouter · Web	http://192.168.1.1 (opens in a new tab)	admin	admin	Dual-WAN business SD-WAN router: one Gigabit Ethernet WAN plus an embedded Cat-4/Cat-7 LTE modem and a FlexModule slot; the Wi-Fi variant adds 802.11ac. Genuine static admin/admin default, and Peplink forces a password change on the first successful login. Confirm the LAN IP against the device label — the manual is Balance-line-generic. Manufacturer (opens in a new tab) Recovery & reset instructions With a paperclip, press and hold the recessed reset button — ~5-10 seconds for an admin-password reset (status LED blinks red twice) or ~20 seconds for a full factory reset (blinks red three times) — then release. After reboot, browse to https://192.168.1.1 and log in.
PeplinkBalance 310XRouter · Web	http://192.168.1.1 (opens in a new tab)	admin	admin	Enterprise/branch SD-WAN multi-WAN router (all-gigabit ports, 2.5 Gbps routing throughput, patented SpeedFusion bonding), managed via the on-box Web Admin Interface or InControl2 cloud. Genuine documented static default admin/admin; the manual recommends but does not force a change. Read-only account is user/user. Manufacturer (opens in a new tab) Recovery & reset instructions Hold the recessed reset button on the unit to restore factory defaults, which returns the Web Admin login to admin/admin at http://192.168.1.1. Change the Admin/Read-only passwords under System > Admin Security.
PeplinkBalance 380Router · Web	http://192.168.1.1 (opens in a new tab)	admin	admin	Mid-tier multi-WAN SD-WAN router/firewall (configurable gigabit WAN/LAN ports, SpeedFusion bonding) positioned above the Balance 310X already covered, for medium-business deployments. Genuine documented static default admin/admin; read-only account is user/user. Manufacturer (opens in a new tab) Recovery & reset instructions With a paperclip, press and hold the recessed reset button on the back panel for about 10-20 seconds until all LEDs flash, then release to restore factory defaults; from firmware 5.4+ the admin password alone can also be reset via Maintenance > Reset Admin Password on the front LCD panel. Browse to http://192.168.1.1 and log in with admin/admin.
PeplinkBalance OneRouter · Web	http://192.168.1.1 (opens in a new tab)	admin	admin	Dual-WAN SD-WAN router (Ethernet + optional embedded cellular) for SMB/branch use, desktop form factor with no built-in Wi-Fi radio — Peplink's entry point above the Balance 20X. Genuine static default admin/admin confirmed in the official Balance series manual. Manufacturer (opens in a new tab) Recovery & reset instructions With a paperclip, press and hold the recessed reset button on the back panel for about 10-20 seconds until all LEDs flash, then release to restore factory defaults. Browse to https://192.168.1.1 and log in with admin/admin.
PeplinkMAX BR1Modem / gateway · Web	http://192.168.50.1 (opens in a new tab)	admin	admin	Compact mobile 4G/LTE cellular router/gateway with a single embedded modem, DIN-rail or wall mountable for vehicle/IoT deployments. Genuine static default admin/admin confirmed in the official Pepwave MAX firmware manual, on a distinct default LAN IP (192.168.50.1) from the Balance line. Manufacturer (opens in a new tab) Recovery & reset instructions With a paperclip, press and hold the recessed reset button for about 10-20 seconds until all LEDs flash, then release to restore factory defaults. Browse to https://192.168.50.1 and log in with admin/admin.
PeplinkMAX BR2Router · Web	http://192.168.50.1 (opens in a new tab)	admin	admin	Rugged dual-SIM/dual-cellular Pepwave MAX router for M2M and fixed-site failover (on-board Wi-Fi AP, gigabit Ethernet WAN/LAN), documented in the MAX Series User Manual 8.4.0 section 2.44. Managed via the on-box Web Admin or InControl2 cloud. The static admin/admin default is transient — first logon mandates a password change. Manufacturer (opens in a new tab) Recovery & reset instructions Rugged dual-cellular M2M/fleet LTE router. Press and hold the reset button to restore factory defaults; the Web Admin returns to admin/admin at http://192.168.50.1, after which the firmware forces a new 10-character password (mixed case plus a digit) on first logon.
PeplinkMAX BR2 ProRouter · Web	http://192.168.50.1 (opens in a new tab)	admin	admin	Ruggedized dual-embedded-cellular-modem router for vehicle/vessel mounting — the higher-throughput 'Pro' tier of the MAX BR2 line already covered. Genuine documented static default admin/admin in the Pepwave MAX manual, same forced-change behavior as the base BR2. Manufacturer (opens in a new tab) Recovery & reset instructions With a paperclip, press and hold the recessed reset button for about 10-20 seconds until all LEDs flash, then release to restore factory defaults. Browse to http://192.168.50.1 and log in with admin/admin, after which the firmware forces a new password.
PeplinkMAX TransitRouter · Web	http://192.168.50.1 (opens in a new tab)	admin	admin	Pepwave MAX Transit cellular router built for vehicles and public transit (integrated GPS, Wi-Fi AP, gigabit Ethernet), covered by the MAX Series User Manual 8.4.0 Transit variant sections. Runs from the local Web Admin or InControl2. Ships with the documented admin/admin default but compels an immediate password change at first successful login. Manufacturer (opens in a new tab) Recovery & reset instructions In-vehicle transit cellular router with GPS. Hold the recessed reset button until the unit reboots to factory settings; login reverts to admin/admin at http://192.168.50.1 and you must define a fresh password (minimum ten characters, upper and lower case, including a number) before the dashboard loads.
PeplinkMAX Transit Duo ProRouter · Web	http://192.168.50.1 (opens in a new tab)	admin	admin	A fleet/transit mobility router carrying dual embedded LTE-A Pro modems (no 5G) across 4 SIM slots plus GPS and 4 SMA cellular connectors — genuinely distinct from the already-seeded single-modem MAX Transit and the dual-5G-modem MAX BR2 Pro. Pepwave's official firmware manual states: "enter the following LAN IP address... http://192.168.50.1 (This is the default LAN IP address for Pepwave routers.) ... Username: admin Password: admin." Manufacturer (opens in a new tab) Recovery & reset instructions With a paperclip, press and hold the recessed reset button for about 10-20 seconds until all LEDs flash, then release to restore factory defaults. Browse to http://192.168.50.1 and log in with admin/admin, after which the firmware forces a new password.
PeplinkSurf SOHO MK3Router · Web	http://192.168.50.1 (opens in a new tab)	admin	admin	SOHO router with a simultaneous dual-band 802.11ac access point, 4x Gigabit Ethernet, USB LTE/3G failover WAN and three dual-band SMA antennas. Genuine static admin/admin default; Peplink forces a password change on the first successful login. Default LAN IP is 192.168.50.1. Manufacturer (opens in a new tab) Recovery & reset instructions Locate the reset button on the back panel; with a paperclip press and hold it ~10 seconds for a factory reset (status LED turns red), then release. After reboot, browse to https://192.168.50.1 and log in.

Related login addresses

GET CONNECTED

How to reach your router

Connect your computer or phone to the router’s Wi-Fi or an Ethernet port.
Open a documented login address. If it does not load, look for the Router or Default gateway address in your device’s network settings.
Match your model and hardware revision to the table. Use the device label or your setup password when the model has no shared default.

Admin password or Wi-Fi password?

The admin password opens the router’s settings. The Wi-Fi password connects a device to the wireless network. They may be different, and an ISP or cloud account can be separate again.

If the password does not work

Check capitalization and the device label, then use the manufacturer’s password-recovery instructions. A factory reset erases settings and may require ISP setup details; follow the instructions for your exact model.

Find your model’s manual →

Sources & data

Router default-credential data from ssid.ai (Drumworks Ventures FZ), licensed CC BY 4.0. Adapted, organized and supplemented by Manuals+. The data is provided as is; manufacturers and ISPs can change defaults.

Additional factual entries: Austin Songer’s credential list and Clint Milner’s credential list. Each table entry links to its supporting source. Updated 2026-10-16.