Skip to content

NetComm router & modem login

Find the login address and access method for your NetComm model. Check the model details for a device-label password, a setup password, a documented default, or app access.

Connect to the router’s Wi-Fi or Ethernet first. If the address does not open, look for Router or Default gateway in your network settings.

QUICK START

Most likely login options

See every listed combination ↓

Start with the option that matches your model. Defaults apply to the factory state; use the password you chose if the device has already been set up.

1

Check the device label

Username
admin
Password / access
Password on the device label

Access: Web

NF18MESH (CloudMesh Gateway), NF20, NF20MESH

2

Default credentials

Username
admin
Password / access
admin

Access: Web

NB5, NF18ACV

3

Default credentials

Username
admin
Password / access
password

Access: Not specified

NB1300

Options are ordered by manufacturer documentation and coverage among the listed models. Hardware, firmware, and ISP versions can differ.

MODEL DETAILS

Login addresses & credentials

9 records

Passwords are case-sensitive. “Leave blank” means an empty field; “Not specified” means the source does not provide that detail. Entries without a model are brand-level references.

Models, login addresses, credentials, instructions and sources
Model / deviceLogin addressUsernamePassword / accessNotes & source
NetComm–Router · Not specified–No username requiredadmin

Model not specified by this list.

NetComm–Router · Not specified–adminpassword

Model not specified by this list.

NetComm–Router · Not specified–userpassword

Model not specified by this list.

NetCommNB1300Router · HTTP–adminpassword

Defaults may depend on the listed model, revision, firmware or ISP.

NetCommNB5Router · Not specified–adminadmin

Defaults may depend on the listed model, revision, firmware or ISP.

NetCommNF18ACVModem / gateway · Webhttp://192.168.20.1 (opens in a new tab)adminadmin

VDSL2/ADSL2+ dual-band AC1600 Gigabit Gateway with VoIP — a genuine static default, distinct from the already-seeded label-unique NetComm NF20MESH (Aussie Broadband). Official NetComm Wireless NF18ACV Wireless Setup Guide states: "User Name: admin" and "Password: admin".

Recovery & reset instructions

Hold the recessed reset button on the rear panel for ~10 seconds until the power LED flashes, then release; gateway reboots to factory defaults.

NetCommNF18MESH (CloudMesh Gateway)Mesh system · Webhttp://cloudmesh.home (opens in a new tab)http://192.168.20.1 (opens in a new tab)adminPassword on the device label

802.11a/b/g/n/ac dual-band mesh gateway, an earlier CloudMesh generation than the already-seeded NF20MESH — label-unique like its sibling, not a shared default. Official NetComm NF18MESH CloudMesh Gateway User Guide states: "Enter the default Username 'admin' (all letters are lowercase) and the unique Password which is printed on the label on the back of the NF18MESH."

Recovery & reset instructions

Hold the recessed reset button for ~10 seconds until the LEDs flash, then release; gateway reboots to the original factory-label password.

NetCommNF20Modem / gateway · Webhttp://192.168.20.1 (opens in a new tab)adminPassword on the device label

Standalone Wi-Fi 6 (802.11ax) dual-band gateway (non-mesh SKU) — a distinct hardware tier from the same brand's mesh-line NF18MESH/NF20MESH in this run and the existing seed. Official NetComm NF20 User Guide (UG01346) states: "In the Password field, type the unique password printed on the label on the bottom of the gateway, then click on the Login > button."

Recovery & reset instructions

Hold the recessed reset button for ~10 seconds until the LEDs flash, then release; gateway reboots to the original factory-label password.

NetCommNF20MESHModem / gateway · Webhttp://192.168.20.1 (opens in a new tab)adminPassword on the device label

Listed as NetComm (Aussie Broadband). Aussie Broadband's standard-issue NBN modem/router. Official setup guide: "Type 192.168.20.1 in the address bar and press Enter... your username is 'admin'" and the password "will be listed on the sticker on the base of the Netcomm router" — explicitly distinct from the WiFi password ("The password needed here is different than the WiFi Password"). Resolves a prior run's 'model-ambiguous' exclusion.

Recovery & reset instructions

A factory reset (physical reset button) restores admin login to the credentials printed on the sticker on the base of the unit — not to a shared admin/admin default.

Related login addresses

GET CONNECTED

How to reach your router

  1. Connect your computer or phone to the router’s Wi-Fi or an Ethernet port.
  2. Open a documented login address. If it does not load, look for the Router or Default gateway address in your device’s network settings.
  3. Match your model and hardware revision to the table. Use the device label or your setup password when the model has no shared default.

Admin password or Wi-Fi password?

The admin password opens the router’s settings. The Wi-Fi password connects a device to the wireless network. They may be different, and an ISP or cloud account can be separate again.

If the password does not work

Check capitalization and the device label, then use the manufacturer’s password-recovery instructions. A factory reset erases settings and may require ISP setup details; follow the instructions for your exact model.

Find your model’s manual →

Sources & data

Router default-credential data from ssid.ai (Drumworks Ventures FZ), licensed CC BY 4.0. Adapted, organized and supplemented by Manuals+. The data is provided as is; manufacturers and ISPs can change defaults.

Additional factual entries: Austin Songer’s credential list and Clint Milner’s credential list. Each table entry links to its supporting source. Updated 2026-10-16.