Use the vendor app
- Username
- Not specified
- Password / access
- Vendor app or account
Access: App
Halo H50G (mesh), Halo H70X (AX1800)
Source (opens in a new tab)ROUTER & MODEM REFERENCE
Mercusys router & modem login
Login addresses, default credentials, and setup instructions for Mercusys equipment.
Open router login http://mwlogin.net (opens in a new tab)Open router login http://192.168.1.1 (opens in a new tab)Open device page http://192.168.68.1 (opens in a new tab)
Connect to the router’s Wi-Fi or Ethernet first. These links open a new tab on your device; the address may differ if the network was reconfigured.
QUICK START
Most likely login options
Start with the option that matches your model. Defaults apply to the factory state; use the password you chose if the device has already been set up.
Options are ordered by manufacturer documentation and coverage among the listed models. Hardware, firmware, and ISP versions can differ.
MODEL DETAILS
Login addresses & credentials
Passwords are case-sensitive. “Leave blank” means an empty field; “Not specified” means the source does not provide that detail. Entries without a model are brand-level references.
| Model / device | Login address | Username | Password / access | Notes & source |
|---|---|---|---|---|
| MercusysHalo H50G (mesh)Mesh system · App | http://mwlogin.net (opens in a new tab)http://192.168.68.1 (opens in a new tab) | Not specified | Vendor app or account | Halo mesh is set up via the MERCUSYS app; the web page at mwlogin.net signs in with the MERCUSYS ID / password you created during app setup. There is no admin/admin default. Recovery & reset instructionsReset a Halo unit: press and hold its RESET button for about 10 seconds until the LED changes, then release and wait for reboot. Reconfigure through the MERCUSYS app; the web page (mwlogin.net or LAN IP 192.168.68.1) signs in with the app credentials you created. |
| MercusysHalo H70X (AX1800)Mesh system · App | http://mwlogin.net (opens in a new tab)http://192.168.1.1 (opens in a new tab) | Not specified | Vendor app or account | AX1800 mesh configured through the MERCUSYS app with a Mercusys ID — no generic default login. The web page at mwlogin.net signs in with that Mercusys ID password. Gateway 192.168.1.1 is Mercusys's standard default (not model-confirmed). Recovery & reset instructionsReset from within the MERCUSYS app, or hold the Reset button on a Halo unit until the LED changes, then re-run setup in the app. |
| MercusysMR70X (AX1800)Router · Web | http://mwlogin.net (opens in a new tab)http://192.168.1.1 (opens in a new tab) | No username required | Password created during setup | No default password. On first access to mwlogin.net the router forces you to create an admin password - there is no admin/admin. (Some older Mercusys models accepted admin/admin, but current firmware does not.) Recovery & reset instructionsReset: with the router powered on, use a pin to press and hold the RESET button on the rear panel for about 10 seconds until it reboots, then release. Browse to http://mwlogin.net (click Advanced to accept the self-signed-certificate warning) and create a new admin password. |
No records match these filters. Try another model or clear the filters.
Related login addresses
GET CONNECTED
How to reach your router
- Connect your computer or phone to the router’s Wi-Fi or an Ethernet port.
- Open a documented login address. If it does not load, look for the Router or Default gateway address in your device’s network settings.
- Match your model and hardware revision to the table. Use the device label or your setup password when the model has no shared default.
Admin password or Wi-Fi password?
The admin password opens the router’s settings. The Wi-Fi password connects a device to the wireless network. They may be different, and an ISP or cloud account can be separate again.
If the password does not work
Check capitalization and the device label, then use the manufacturer’s password-recovery instructions. A factory reset erases settings and may require ISP setup details; follow the instructions for your exact model.
Find your model’s manual →Sources & data
Router default-credential data from ssid.ai (Drumworks Ventures FZ), licensed CC BY 4.0. Adapted, organized and supplemented by Manuals+. The data is provided as is; manufacturers and ISPs can change defaults.
Additional factual entries: Austin Songer’s credential list and Clint Milner’s credential list. Each table entry links to its supporting source. Updated 2026-10-16.