Use the vendor app
- Username
- Not specified
- Password / access
- Vendor app or account
Access: App
eero 6+, eero 7, eero Max 7 and other listed models
Source (opens in a new tab)ROUTER & MODEM REFERENCE
eero router & modem login
Login addresses, default credentials, and setup instructions for eero equipment.
A shared web login address is not listed for this equipment. Check the model instructions below for app access, the device label, or your router’s gateway address.
Connect to the router’s Wi-Fi or Ethernet first. These links open a new tab on your device; the address may differ if the network was reconfigured.
QUICK START
Most likely login options
Start with the option that matches your model. Defaults apply to the factory state; use the password you chose if the device has already been set up.
Options are ordered by manufacturer documentation and coverage among the listed models. Hardware, firmware, and ISP versions can differ.
MODEL DETAILS
Login addresses & credentials
Passwords are case-sensitive. “Leave blank” means an empty field; “Not specified” means the source does not provide that detail. Entries without a model are brand-level references.
| Model / device | Login address | Username | Password / access | Notes & source |
|---|---|---|---|---|
| eeroeero 6+Mesh system · App | App / account access | Not specified | Vendor app or account | App-only. There is no admin web page and no admin/admin default password. The only password is the Wi-Fi password you create in the eero app. Recovery & reset instructionseero 6+ is managed only in the eero app. To hard reset: with the eero powered on, hold the reset button on the back until the LED flashes red (~15 seconds), then release; when it blinks blue it is ready to set up. Re-add it in the app and set your Wi-Fi credentials. |
| eeroeero 7Mesh system · App | App / account access | Not specified | Vendor app or account | Dual-band Wi-Fi 7 mesh router (up to 1.8 Gbps wireless, two 2.5GbE ports), eero's newest entry-tier Wi-Fi 7 unit alongside the already-seeded eero Max 7. Official eero Support: "Your eero network can only be managed using the mobile app, and cannot be configured through a program or web browser using Windows, Linux, or Intel-based Mac machines." Recovery & reset instructionsHold the reset button until the LED flashes yellow (~7 sec) for a soft reset, or until it flashes red (~15 sec) for a full factory reset; release when the LED flashes blue, indicating it is ready to set up again. |
| eeroeero Max 7Mesh system · App | App / account access | Not specified | Vendor app or account | App-only mesh. No web interface and no factory admin/admin. All configuration, including the Wi-Fi password you pick, lives in the eero app under your Amazon/eero account. Recovery & reset instructionsThere is no browser login for eero — use the eero app. To hard reset: powered on, hold the reset button until the LED flashes red (about 15 seconds), release, and wait for the blue blink. Add the eero back in the app and choose a new Wi-Fi name and password. |
| eeroeero Pro 6Mesh system · App | App / account access | Not specified | Vendor app or account | App-only — there is no admin web page and no admin/admin default. You create and change the Wi-Fi password in the eero app under Settings > Wifi name & password. There are no separate router login credentials. Recovery & reset instructionseero has no web admin page — everything is managed in the eero mobile app. To factory (hard) reset: with the eero powered on, press and hold the reset button on the back until the LED flashes red (about 15 seconds), then release. When the light blinks blue the unit is ready. Reopen the eero app (signed into your Amazon/eero account) and add the eero back to your network; you set the Wi-Fi name and password there. |
| eeroeero Pro 6EMesh system · App | App / account access | Not specified | Vendor app or account | App-only. No web admin, no default admin/admin. The Wi-Fi password is one you set in the eero app during setup; view or change it under Settings > Wifi name & password. Recovery & reset instructionseero is administered only through the eero mobile app. To hard reset: with the unit powered on, hold the reset button on the back until the LED flashes red (~15 seconds), then release. Wait for the light to blink blue, then re-add the eero in the app and set your Wi-Fi name and password. |
No records match these filters. Try another model or clear the filters.
GET CONNECTED
How to reach your router
- Connect your computer or phone to the router’s Wi-Fi or an Ethernet port.
- Open a documented login address. If it does not load, look for the Router or Default gateway address in your device’s network settings.
- Match your model and hardware revision to the table. Use the device label or your setup password when the model has no shared default.
Admin password or Wi-Fi password?
The admin password opens the router’s settings. The Wi-Fi password connects a device to the wireless network. They may be different, and an ISP or cloud account can be separate again.
If the password does not work
Check capitalization and the device label, then use the manufacturer’s password-recovery instructions. A factory reset erases settings and may require ISP setup details; follow the instructions for your exact model.
Find your model’s manual →Sources & data
Router default-credential data from ssid.ai (Drumworks Ventures FZ), licensed CC BY 4.0. Adapted, organized and supplemented by Manuals+. The data is provided as is; manufacturers and ISPs can change defaults.
Additional factual entries: Austin Songer’s credential list and Clint Milner’s credential list. Each table entry links to its supporting source. Updated 2026-10-16.