Use your setup password
- Username
- No username required
- Password / access
- Password created during setup
Access: Web
Magic 2 WiFi 6 next, Magic 2 WiFi next
Source (opens in a new tab)ROUTER & MODEM REFERENCE
Devolo router & modem login
Login addresses, default credentials, and setup instructions for Devolo equipment.
A shared web login address is not listed for this equipment. Check the model instructions below for app access, the device label, or your router’s gateway address.
Connect to the router’s Wi-Fi or Ethernet first. These links open a new tab on your device; the address may differ if the network was reconfigured.
QUICK START
Most likely login options
Start with the option that matches your model. Defaults apply to the factory state; use the password you chose if the device has already been set up.
Options are ordered by manufacturer documentation and coverage among the listed models. Hardware, firmware, and ISP versions can differ.
MODEL DETAILS
Login addresses & credentials
Passwords are case-sensitive. “Leave blank” means an empty field; “Not specified” means the source does not provide that detail. Entries without a model are brand-level references.
| Model / device | Login address | Username | Password / access | Notes & source |
|---|---|---|---|---|
| DevoloMagic 1 WiFi miniMesh system · Web | – | No username required | Password on the device label | Powerline (500 Mbps HomePlug) plus Wi-Fi 5 add-on adapter, the current entry point of the Magic 1 WiFi line. Gets a DHCP IP with no fixed default address; discovered via devolo Cockpit/app rather than a hostname. Web interface may be protected by a unique password printed on the type label, per the official manual. Recovery & reset instructionsPress and hold the recessed reset button on the adapter for about 10 seconds until the LEDs flash, or use 'Restore factory settings' in devolo Cockpit or the Home Network App. |
| DevoloMagic 2 WiFi 6 nextMesh system · Web | – | No username required | Password created during setup | Wall-plug Powerline (G.hn) plus dual-band mesh Wi-Fi 6 adapter, up to 3,000 Mbps Wi-Fi, WPA2/WPA3, 2x Gigabit LAN — devolo's Wi-Fi 6 successor to the already-seeded Wi-Fi 5 'Magic 2 WiFi next'. Official manual: "If the web interface is password protected (see type plate), it is recommended to set an individual password when logging in for the first time... The default WiFi key for the initial installation of the Magic 2 WiFi 6 next is the device's WiFi key. You will find the unique key on the label on the back of the housing." Recovery & reset instructionsPress and hold the PLC/reset button (next to the network jacks) for about 10 seconds until the LED flashes red at 0.5-second intervals — this restores factory defaults and the Wi-Fi key reverts to the unique key printed on the housing label. |
| DevoloMagic 2 WiFi nextMesh system · Web | – | No username required | Password created during setup | Wall-plug Powerline (G.hn, up to 2400 Mbps) plus dual-band mesh Wi-Fi 5 adapter (802.11a/b/g/n/ac up to 1200 Mbps, 4 antennas, band steering/roaming), with a pass-through socket and 2x gigabit LAN; sold in devolo's 'Mesh WiFi 2' kits. The built-in web interface has NO default password — assigning a login password is mandatory on first login. No fixed default IP: reach the UI via devolo Cockpit or the Home Network App. The Wi-Fi key (separate from the admin login) is unique and printed on the housing label. Recovery & reset instructionsPress and hold the Reset button (next to the network jacks) for longer than 10 seconds until the LED flashes white, then disconnect from mains — this restores factory defaults (all settings lost). |
No records match these filters. Try another model or clear the filters.
GET CONNECTED
How to reach your router
- Connect your computer or phone to the router’s Wi-Fi or an Ethernet port.
- Open a documented login address. If it does not load, look for the Router or Default gateway address in your device’s network settings.
- Match your model and hardware revision to the table. Use the device label or your setup password when the model has no shared default.
Admin password or Wi-Fi password?
The admin password opens the router’s settings. The Wi-Fi password connects a device to the wireless network. They may be different, and an ISP or cloud account can be separate again.
If the password does not work
Check capitalization and the device label, then use the manufacturer’s password-recovery instructions. A factory reset erases settings and may require ISP setup details; follow the instructions for your exact model.
Find your model’s manual →Sources & data
Router default-credential data from ssid.ai (Drumworks Ventures FZ), licensed CC BY 4.0. Adapted, organized and supplemented by Manuals+. The data is provided as is; manufacturers and ISPs can change defaults.
Additional factual entries: Austin Songer’s credential list and Clint Milner’s credential list. Each table entry links to its supporting source. Updated 2026-10-16.