ROUTER & MODEM REFERENCE

Comfast router & modem login

Connect to the router’s Wi-Fi or Ethernet first. These links open a new tab on your device; the address may differ if the network was reconfigured.

QUICK START

Most likely login options

See every listed combination ↓

Start with the option that matches your model. Defaults apply to the factory state; use the password you chose if the device has already been set up.

Default credentials

Username: No username required
Password / access: admin

Access: Web

CF-EW73, CF-WR773BE V2

Source (opens in a new tab)

Use your setup password

Username: No username required
Password / access: Password created during setup

Access: Web

CF-WR627AX

Source (opens in a new tab)

Options are ordered by manufacturer documentation and coverage among the listed models. Hardware, firmware, and ISP versions can differ.

MODEL DETAILS

Login addresses & credentials

3 records

Passwords are case-sensitive. “Leave blank” means an empty field; “Not specified” means the source does not provide that detail. Entries without a model are brand-level references.

Models, login addresses, credentials, instructions and sources
Model / device	Login address	Username	Password / access	Notes & source
ComfastCF-EW73Access point · Web	http://192.168.10.1 (opens in a new tab)	No username required	admin	Outdoor 2.4G repeater/bridge AP, PoE-powered, PoE LAN + LAN/WAN port, default broadcast SSID COMFAST_XXXX_2G — an AP-category row (not a home router). Comfast's official Quick Installation Guide states verbatim: "Open the computer browser, and input 192.168.10.1 to get into the device login page (Default password:admin)" — a password-only login prompt with no separate username field, distinct from third-party aggregator claims of a paired admin/admin login. Manufacturer (opens in a new tab) Recovery & reset instructions Consult the device's physical reset button for a hard factory reset; the QIG does not state a hold time beyond the standard AP/Bridge/Router/Repeater wizard reset.
ComfastCF-WR627AXMesh system · Web	http://192.168.0.1 (opens in a new tab)	No username required	Password created during setup	Wi-Fi 6 mesh-capable router with a dedicated EasyMesh pairing button, 4 antennas, WAN + 3x LAN ports, dual-band 2.4G/5G. No default admin password — the official quick installation guide confirms the setup wizard forces password creation on first login. Manufacturer (opens in a new tab) Recovery & reset instructions With the device powered on, press the RESET button next to the LAN port for about 7 seconds until reset succeeds; on first login after reset the device goes straight to the setup wizard, which requires creating a password (used as both the Wi-Fi and router-admin password).
ComfastCF-WR773BE V2Access point · Web	http://192.168.10.1 (opens in a new tab)	No username required	admin	Plug-in Wi-Fi range extender/repeater (not a full router), single LAN/WAN port, dual-band 2.4G/5G, 4 operating modes (repeater/bridge/AP/router). Official quick installation guide confirms a genuine static default password 'admin' to enter setup, immediately followed by a mandatory password-set step. Manufacturer (opens in a new tab) Recovery & reset instructions Press and hold the WPS/RESET button for about 6 seconds until the WiFi LED (which blinks once per second) turns off and stops blinking; release to restore factory defaults.

Related login addresses

GET CONNECTED

How to reach your router

Connect your computer or phone to the router’s Wi-Fi or an Ethernet port.
Open a documented login address. If it does not load, look for the Router or Default gateway address in your device’s network settings.
Match your model and hardware revision to the table. Use the device label or your setup password when the model has no shared default.

Admin password or Wi-Fi password?

The admin password opens the router’s settings. The Wi-Fi password connects a device to the wireless network. They may be different, and an ISP or cloud account can be separate again.

If the password does not work

Check capitalization and the device label, then use the manufacturer’s password-recovery instructions. A factory reset erases settings and may require ISP setup details; follow the instructions for your exact model.

Find your model’s manual →

Sources & data

Router default-credential data from ssid.ai (Drumworks Ventures FZ), licensed CC BY 4.0. Adapted, organized and supplemented by Manuals+. The data is provided as is; manufacturers and ISPs can change defaults.

Additional factual entries: Austin Songer’s credential list and Clint Milner’s credential list. Each table entry links to its supporting source. Updated 2026-10-16.