Use your setup password
- Username
- admin
- Password / access
- Password created during setup
Access: Web
Quantum Spark 1600, Quantum Spark 1800
Source (opens in a new tab)ROUTER & MODEM REFERENCE
Check Point router & modem login
Login addresses, default credentials, and setup instructions for Check Point equipment.
Open router login http://192.168.1.1 (opens in a new tab)Open router login https://192.168.1.1:4434 (opens in a new tab)
Connect to the router’s Wi-Fi or Ethernet first. These links open a new tab on your device; the address may differ if the network was reconfigured.
QUICK START
Most likely login options
Start with the option that matches your model. Defaults apply to the factory state; use the password you chose if the device has already been set up.
Options are ordered by manufacturer documentation and coverage among the listed models. Hardware, firmware, and ISP versions can differ.
MODEL DETAILS
Login addresses & credentials
Passwords are case-sensitive. “Leave blank” means an empty field; “Not specified” means the source does not provide that detail. Entries without a model are brand-level references.
| Model / device | Login address | Username | Password / access | Notes & source |
|---|---|---|---|---|
| Check Point–Router · Not specified | – | admin | abc123 | Model not specified by this list. |
| Check Point–Router · Not specified | – | admin | adminadmin | Model not specified by this list. |
| Check Point–Router · Not specified | – | admin | admin | Model not specified by this list. |
| Check PointQuantum Spark 1600Modem / gateway · Web | https://192.168.1.1:4434 (opens in a new tab)http://192.168.1.1 (opens in a new tab) | admin | Password created during setup | First whole-brand coverage of Check Point's small-business security gateway line. Check Point's own admin documentation states: "We recommend that you change the default 'admin' login name of the administrator," with the appliance reached at https://192.168.1.1:4434 and the First Time Configuration Wizard requiring a new password — there is no static factory password. Recovery & reset instructionsConnect a PC to a LAN port, browse to https://192.168.1.1:4434 — the First Time Configuration Wizard launches automatically. The default administrator login name is 'admin'; the wizard requires you to create a strong password (min. 6 characters, upper+lower case, special character) before the gateway will complete setup. To factory reset, use the hardware reset button or the Gaia CLI 'reboot_to_factory_defaults' command. |
| Check PointQuantum Spark 1800Modem / gateway · Web | https://192.168.1.1:4434 (opens in a new tab)http://192.168.1.1 (opens in a new tab) | admin | Password created during setup | A higher-tier sibling of this run's Quantum Spark 1600, from the same R81.10.X Locally-Managed Admin Guide covering the 1500-2000 series: "Browse to default gateway IP address: https://192.168.1.1:4434," with the admin login name 'admin' set during the First Time Wizard and no static default password. Recovery & reset instructionsConnect a PC to a LAN port, browse to https://192.168.1.1:4434 to launch the First Time Configuration Wizard. Default admin login name is 'admin'; a new password must be created during the wizard (no static default password). Factory reset via the hardware reset button or Gaia CLI 'reboot_to_factory_defaults'. |
| Check PointSECUREPLATFORM Rev. NG FP3Router · CONSOLE | – | admin | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
No records match these filters. Try another model or clear the filters.
Related login addresses
GET CONNECTED
How to reach your router
- Connect your computer or phone to the router’s Wi-Fi or an Ethernet port.
- Open a documented login address. If it does not load, look for the Router or Default gateway address in your device’s network settings.
- Match your model and hardware revision to the table. Use the device label or your setup password when the model has no shared default.
Admin password or Wi-Fi password?
The admin password opens the router’s settings. The Wi-Fi password connects a device to the wireless network. They may be different, and an ISP or cloud account can be separate again.
If the password does not work
Check capitalization and the device label, then use the manufacturer’s password-recovery instructions. A factory reset erases settings and may require ISP setup details; follow the instructions for your exact model.
Find your model’s manual →Sources & data
Router default-credential data from ssid.ai (Drumworks Ventures FZ), licensed CC BY 4.0. Adapted, organized and supplemented by Manuals+. The data is provided as is; manufacturers and ISPs can change defaults.
Additional factual entries: Austin Songer’s credential list and Clint Milner’s credential list. Each table entry links to its supporting source. Updated 2026-10-16.