Check the device label
- Username
- No username required
- Password / access
- Password on the device label
Access: Web
BGW210-700, BGW320 All-Fi Hub, Wi-Fi Gateway (2Wire / Pace / BGW / NVG)
Source (opens in a new tab)ROUTER & MODEM REFERENCE
AT&T router & modem login
Login addresses, default credentials, and setup instructions for AT&T equipment.
Connect to the router’s Wi-Fi or Ethernet first. These links open a new tab on your device; the address may differ if the network was reconfigured.
QUICK START
Most likely login options
Start with the option that matches your model. Defaults apply to the factory state; use the password you chose if the device has already been set up.
Options are ordered by manufacturer documentation and coverage among the listed models. Hardware, firmware, and ISP versions can differ.
MODEL DETAILS
Login addresses & credentials
Passwords are case-sensitive. “Leave blank” means an empty field; “Not specified” means the source does not provide that detail. Entries without a model are brand-level references.
| Model / device | Login address | Username | Password / access | Notes & source |
|---|---|---|---|---|
| AT&T–Router · Not specified | – | Not specified | mcp | Model not specified by this list. |
| AT&TBGW210-700Modem / gateway · Web | http://192.168.1.254 (opens in a new tab) | No username required | Password on the device label | The BGW210 uses a per-device 'Device Access Code' on the label, not a shared password. Older third-party lists cite 'attadmin', but current units authenticate only with the unique code printed on the gateway. Recovery & reset instructionsBrowse to http://192.168.1.254. No username is required; enter the Device Access Code from the sticker on the side/bottom of the BGW210 when prompted to change settings. To restore factory defaults and reset the access code, press and hold the recessed Reset button ~10 seconds (hold ~15-20 seconds for a full reset), then authorize using the label's Device Access Code. |
| AT&TBGW320 All-Fi HubModem / gateway · Web | http://192.168.1.254 (opens in a new tab) | No username required | Password on the device label | AT&T gateways have no admin username and no shared default password. The single credential is the per-device 'Device Access Code' printed on the gateway label — each unit is different, so no universal default exists. Recovery & reset instructionsOpen a browser to http://192.168.1.254 to reach the gateway UI. There is no username; when a setting asks for authorization, enter the Device Access Code printed on the sticker on the side of the BGW320 (a unique alphanumeric string). To reset the access code, press and hold the recessed Reset button on the side for ~10 seconds; a longer 15-20 second hold performs a full factory reset. After reset, use the Device Access Code printed on the label. |
| AT&TWi-Fi Gateway (2Wire / Pace / BGW / NVG)Modem / gateway · Web | http://192.168.1.254 (opens in a new tab) | No username required | Password on the device label | AT&T's 2Wire/Pace/BGW/NVG gateways do not use admin/admin — each unit has a unique Device Access Code printed on a sticker on the gateway. AT&T's official support confirms the code lives on the device label and is reset to that label value by a factory reset. Recovery & reset instructionsOpen a browser to http://192.168.1.254 to reach the Gateway User Interface. When asked for a Device Access Code, enter the code printed on the sticker on the side or bottom of the gateway. To reset, press and hold the Reset button for about 10 seconds until the gateway restarts; the access code reverts to the one on the label. |
No records match these filters. Try another model or clear the filters.
Related login addresses
GET CONNECTED
How to reach your router
- Connect your computer or phone to the router’s Wi-Fi or an Ethernet port.
- Open a documented login address. If it does not load, look for the Router or Default gateway address in your device’s network settings.
- Match your model and hardware revision to the table. Use the device label or your setup password when the model has no shared default.
Admin password or Wi-Fi password?
The admin password opens the router’s settings. The Wi-Fi password connects a device to the wireless network. They may be different, and an ISP or cloud account can be separate again.
If the password does not work
Check capitalization and the device label, then use the manufacturer’s password-recovery instructions. A factory reset erases settings and may require ISP setup details; follow the instructions for your exact model.
Find your model’s manual →Sources & data
Router default-credential data from ssid.ai (Drumworks Ventures FZ), licensed CC BY 4.0. Adapted, organized and supplemented by Manuals+. The data is provided as is; manufacturers and ISPs can change defaults.
Additional factual entries: Austin Songer’s credential list and Clint Milner’s credential list. Each table entry links to its supporting source. Updated 2026-10-16.