N1B1 Cordless Rivet Nut Setter
“
Product Specifications:
- Model: N1B1
- Power Source: Cordless
- Manufacturer: Lobtex Co., Ltd.
- Country of Origin: Japan
- Website: https://www.lobtex.co.jp/
Product Usage Instructions:
1. Initial Setup:
- Ensure all components are included as per the set
contents. - Charge the battery pack using the provided charger until the
LED lamp shows green. - Insert the battery pack into the battery pack attachment
section on the machine body.
2. Operation:
- Press the button to activate the machine.
- Select the appropriate rivet nut size based on the work
requirements. - Place the rivet nut in the claw and position it securely.
- Align the machine with the workpiece and gently press to set
the rivet nut in place.
3. Maintenance:
- Regularly clean ventilation holes to ensure proper
cooling. - Inspect the machine body and components for any signs of wear
or damage. - Store the machine in a dry and safe place when not in use.
Frequently Asked Questions (FAQ):
Q: How do I troubleshoot if the machine is not setting the
rivet nuts properly?
A: Check the alignment of the machine with the workpiece, ensure
the correct rivet nut size is being used, and inspect for any
obstructions in the claw or machine body.
Q: Can I use parts other than the recommended ones with this
machine?
A: It is not recommended to use parts other than those specified
in the instruction manual as it may lead to damage or injury, and
the manufacturer does not guarantee their compatibility.
“`
Cordless Rivet Nut Setter Easy Guide
N1B1
Original Easy Guide
Thank you for purchasing the cordless rivet nut setter (hereinafter referred to as this machine).
About the instruction manual
· An instruction manual is not included with this machine. When using the product, be sure to read the instruction manual published on the Lobtex Co., Ltd. website together with the Easy Guide (this document) to ensure proper use.
· Please access the instruction manual from the URL below on your computer/smartphone and read it together with this document.
https://www.lobtex.co.jp/english/products/tabid/153/pdid/E-N1B1/catid/108/Default.aspx · After reading this manual, please keep it in a safe place with this machine.
For smartphone
Introduction
· This machine is a dedicated tool for crimping and fastening blind rivet nuts (hereafter referred to as rivet nuts). It is not designed, manufactured, or sold for any other purposes.
· Please use rivet nuts whose specifications and strength have been thoroughly designed and considered by the customer.
Easy Guide (this document), Safety Guide and Instruction Manual Instructions for using this machine are divided into the Easy Guide (this document), Safety Guide, and Instruction Manual. Depending on the information you need, refer to the Easy Guide (this document), Safety Guide, or Instruction Manual.
Main contents described in the Easy Guide (this document)
Name of each part Set contents Initial setting method Serial No.
Main contents of the Safety Guide
General safety warnings for power tools Safety warnings/cautions for cordless rivet nut setter
Main contents of the Instruction Manual
Safety precautions Names of each part Specifications Preparation before use Adjustment method Work procedure Error display list Output setting table for each rivet nut Troubleshooting How to order parts
2 Important Notice
Before using this machine, please read this manual and the instruction manual/safety guide carefully. In addition, please follow the instructions in this manual when handling this machine and when replacing accessories and parts.
If you have any questions about this manual and the instruction manual/safety guide, please contact the store where you purchased it or the Lobtex Co., Ltd. (hereinafter referred to as our company) call center.
It is not possible to predict all the dangers that may be mixed with this machine and to include them in this manual and the instruction manual/safety guide. When using this machine, please pay careful attention to safety measures in addition to what is written in this manual and the instruction manual/safety guide.
This manual and the instruction manual/safety guide are written in Japanese as the original language. Please fully understand the contents of this manual and the instruction manual/safety guide at your own responsibility.
The copyright of this manual and the instruction manual/safety guide is owned by our company. It is prohibited to publish, copy, reproduce, or translate the contents of this manual and the instruction manual/safety guide into another language without permission.
3 Disclaimer
We do not compensate for direct or indirect injury or lost profits caused by misuse, abuse or unauthorized modification of this unit, nor do we guarantee the strength of the blind nuts themselves.
We are not liable for any damage or injury caused by modifications made without our written approval. We are not liable for any damage or injury caused by the use of parts other than the recommended parts.
Call center Tel: +81-72-980-1111 Fax: +81-72-980-1166
12-8 Shijo-cho, Higashi-Osaka City, Osaka 579-8053, Japan
Website https://www.lobtex.co.jp/ No.NEN1B1SK2A31
Charger
LED lamp green/red
Ventilation holes
power cable
Battery pack attachment section Ventilation holes
Inlet Plug
Power plug for North America
Battery pack
claw
Terminal
For Europe
button
Names of components
Machine bodyN1B1
Connection terminal cover
Nose Housing
Work light (LED light)
hanger
Lock nut
Up button Select button
Nosepiece Screw mandrel
Indicator Panel
Trigger Switch
No
STROKE
LOCK FORCE
Down button Save button Ventilation holes
Forward/reverse switch
E
F
Battery level indicator *Only lights up when in use
Work light ON/OFF button
Battery pack (BPL-1825 included) *Large capacity battery pack is optional (BPL-1850)
Replacement parts when changing fastening nuts
Set contents
Please make sure that all of the following items, including this unit, are included in the dedicated blow case. We take every precaution when packaging, but if any item is missing, please contact the retailer where you purchased the product or our call center.
Cordless Rivet Nut Setter N1B1
Nosepiece
M3 M4M5
M6M8M10
* The product is shipped with an M6 nosepiece attached.
double-ended spanner Hexagonal L-shaped
(2 pieces)
wrench
Screw mandrel M3 M4M5
Nosepiece
Lock nut
Screw mandrel
*Lock nuts are common to all sizes.
Installation of Pokayoke tools
If you purchase the dedicated Pokayoke installation kit (PYSN1H80), you can install the Pokayoke tool (model number TW-800T) from HERUTU ELECTRONICS CORPORATION.
* Please contact our call center for information on wireless transmitter specifications and Pokayoke installation kits.
Charger
power cable
M6M8M10
for North America For Europe
* The product is shipped with an M6 screw mandrel attached.
Battery pack(BPL-1825)
Easy Guide (this document)
Safety Guide
Initial setting method
Please refer to the table below when entering stroke and output settings. For preparations before use and more detailed operating instructions, download the instruction manual from our website and follow the “Preparation before use” section.
How to input and adjust stroke and output
The stroke and output of this machine must be adjusted according to the thickness of the rivet nut and base material used. Follow the procedure below to input the rivet stroke and output, and adjust so that the rivet nut is properly fitted. Input is done using the buttons next to the monitor display screen.
Up button
No STROKE
LOCK FORCE
Down button
Select button Save button
CAUTION
If no button is pressed for about 3 minutes,
the power will turn off. If the input has not been saved, the input will not be reflected and
the previous settings will be restored.
1 When you pull the trigger switch, the power turns on and the display lights up on the monitor.
2 Press the Select button ( ). (For more than 3 seconds but less than 5 seconds) The first two characters will be fully lit, the last two characters will be half lit, and the bar for the second character will be in the center, and the memory number selection screen for saving the settings will appear. Press the Up button ( ) and Down button ( ) to select the memory number to register. (This unit can save 10 settings from memory numbers 0 to 9.)
No STROKE
LOCK FORCE
No STROKE
LOCK FORCE
3 Press the Select button ( ) to enter the stroke. (Less than 3 seconds) The first character will be half lit, the next three characters will be fully lit, and the bar for
the second character will move to the STROKE position above, and the screen for entering
the stroke will appear. Press the Up button ( ) and Down button ( ) to enter the
stroke (long press to fast forward). The stroke can be set between 0.1 and 10 mm in 0.1 mm
increments.
No STROKE
LOCK FORCE
No STROKE
LOCK FORCE
CAUTION
If you continue to press the Select button ( ) for more than 3 seconds, your input will be
discarded and you will return to the initial screen.
5 Press the Save button ( ). (For 2 seconds or more) [Settings complete] 2 the settings will be saved to the memory number selected in [Settings complete]. If
you want to check the settings you entered, press the Select button ( ). The stroke
and output settings will be displayed.
<Stroke Display>
<Output Display>
No STROKE
No STROKE
LOCK FORCE
LOCK FORCE
CAUTION
1. If you press the Select button ( ) instead of the Save button ( ) (for less than 3
seconds), you will return to the memory number selection screen 2 .
2. If you press the Select button ( ) for more than 3 seconds instead of the Save button
( ), any newly entered settings will be discarded and you will return to the initial screen.
6 Adjust the rivet nut you are using by actually tightening it.
Measure the total length of the rivet nut before caulking. Measure the total length of the rivet nut after caulking, and
calculate the actual caulking margin by subtracting the dimension before caulking from the dimension after caulking. * When tightening the rivet nuts, refer to the “Work Procedure” in the instruction manual.
Caulking dimension ( ) = Total length of nut before caulking – Total length of nut after caulking
Adjust the stroke input value so that the caulking margin is within ± 0.3mm of the appropriate caulking margin. Even if you adjust the stroke input value, if the appropriate crimping distance cannot be achieved, the output may not be enough. Adjust by increasing the output one step at a time.
rivet nut
CAUTION
1. Since there are individual differences between aircraft, adjustment is required for each aircraft even if the same rivet nut is used.
2. When increasing the adjustment value, increase it gradually. If it is raised too high, it may damage the threads of the rivet nut or damage the machine body, such as the screw chuck.
3. If the stroke is too small or the force is too weak,The rivet nut may not be tightened enough and may cause the rivet nut to spin idly.
4. If the stroke is too large and the output is too strong, the rivet nut may be too tight and the thread may break.
Large stroke and force will damage the nut.
Regarding the stroke value to enter, check the thickness of the base material and check the appropriate caulking from the caulking table attached to the rivet nut you are using.
Rivet nut crimping margin ( )
(Examples)
When the rivet nut caulking table is on
3.5
the right, and the base material thickness
(caulking plate thickness) is 1.0 mm, the
appropriate caulking amount is 3.5 mm.
CAUTION
Since there are individual differences
between aircraft, adjustments must be
made at the end.
1.02.0 Caulking plate thickness (t)
4 Press the Select button ( ) to proceed to the crimp output input. (Less than 3 seconds) The first character will be half lit, the next 3 characters will be fully lit, the bar for the second character will move to the FORCE position below, and the screen for inputting the output will appear. Press the Up button ( ) and Down button ( ) to input the output (long press to fast forward). The output can be set in increments of 1 between 01 and 99.
No STROKE
LOCK FORCE
No STROKE
LOCK FORCE
For the output value to be entered, please check the value for the rivet nut to be used from the output setting table for each rivet nut (table on the right).
(Examples) If you are using our rivet nut “NSK-6M” , the output setting table will indicate “60” . * If you are using a blind nut from another company that is not listed in the output setting table, please enter “99” .
*The crimping output setting is a function to prevent damage to the screw mandrel or breakage of the rivet nut threads due to excessive crimping (such as double crimping), and is not a function to control the crimping condition by adjusting the output. If you do not need this function, set it to “99” .
CAUTION
1. The number is a number that calls up a pre-set output and is not the actual output value.
2. If you continue to press the Select button ( ) for more than 3 seconds, the input will be
discarded and you will return to the initial screen.
Output value setting table for our rivet nuts
Thread Size
Our product number
Product number (NTK)
NSK
Force No.
NSD NAK NAD NTK NSK-MR NSD-MR
Force No. Force No. Force No. Force No. Force No. Force No.
M3
M4
M5
3M
4M 415M 425M 435M 5M 515M 525M 535M
3M15 4M 4M20 4M25 4M35 5M
– 5M30 –
05
30
20
15
20
40
45
45
35
–
40
15
15
15
70
40
45
50
–
10
10
10
05
20
15
15
15
–
10
10
05
05
20
20
15
15
30
40
40
35
40
55
–
55
–
–
30
–
–
–
45
–
–
–
–
15
–
–
–
50
–
–
–
Thread Size
Our product number
Product number (NTK)
NSK
Force No.
NSD
Force No.
NAK
Force No.
NAD NTK NSK-MR
Force No. Force No. Force No.
NSD-MR
Force No.
M6
M8
6M 625M 640M 8M 825M 840M
6M
– 6M40 8M
– 8M40
60
55
65
65
80
85
65
60
60
85
85
85
40
45
45
70
50
55
45
45
50
55
50
65
55
–
70
65
–
99
60
–
–
95
–
–
70
–
–
95
–
–
* When using the NSK-6M rivet nut, the setting is “60” . * “-” in the table indicates that it is not included in our standard rivet nut lineup.
M10
10M 1025M 1040M
10M
– 10M40
80
85
95
–
85
85
–
55
55
–
55
50
65
–
95
99
–
–
–
–
–
Serial No.
* The serial number of the cordless rivet nut setter is displayed on the bottom of the unit as three letters (date of manufacture) and a five-digit number.
BNU00101
Serial number location
Bottom of main body
How to view the manufacturing year/month
Manufacturing year/month 1 2 3 4 5 6 7 8 9 10 11 12
Code
ABMNKWT YUOL Z
Examples 2 0 Year Month
BN Z
Serial number
BNZ
Documents / Resources
 |
LOBSTER N1B1 Cordless Rivet Nut Setter [pdf] User Guide N1B1, N1B1 Cordless Rivet Nut Setter, Cordless Rivet Nut Setter, Rivet Nut Setter, Nut Setter, Setter |