Z WAGZ ZW-GM Advanced Plug andPlay Module Integration ຄູ່ມືການສອນທີ່ອອກແບບມາ

ເຊື່ອມຕໍ່ຜູ້ຊາຍຂອງ T-Harness ແຕ່ລະຄົນກັບ BCM ແລະ
removed plugs into the female side of the Z-WAGZ BCM
harnessing.
Connect the ZW-GM module LAST to the 22-pin connector and
tie-wrap the unit to another harness if desired.

ການດໍາເນີນງານ:

Pattern 1 will begin to flash upon activation. Hazards in the
gauge cluster will blink once, and the LED on the unit will blink
ສີຟ້າ.
To switch to Pattern 2: Engage either turn signal, then press
and HOLD the high beam lever once more for 5 seconds OR press &
release the provided push button.

To deactivate Z-WAGZ: Press and HOLD the high beam lever OR
press and HOLD the provided push button OR release 12v (+) signal
to the blue wire if connected this way.
PLOW MODE slows down the selected pattern and disables High and
Low beams from flashing when INPUT 2 (violet) receives 12v (+)
before activating the flasher.

ຄຳຖາມທີ່ຖາມເລື້ອຍໆ (FAQ):

Q: What vehicles are compatible with the ZW-GM module?

A: The ZW-GM module is designed for specific GM vehicles,
including Silverado, Sierra, Colorado, Canyon, Tahoe, and Suburban
ຮຸ່ນຈາກ 2014 ຫາ 2022.5.

Q: How can I enable ‘Plow Mode’?

A: ‘Plow Mode’ can be activated by ensuring INPUT 2 (violet)
receives 12v (+) before activating the flasher. This mode disables
High & Low beam flashing and slows down the pattern to prevent
overheating of the relay box.

“`

View Fullscreen

The ZW-GM is an advanced Plug & Play module integration designed for specific GM vehicles for flashing OEM lights in `wig-wag’ similar method with a simple press of a button. This unit comes pre-programmed with various
light patterns and has on-board options for disabling specific lights.

ZW-GM Module

ZW-GM T-Harness

ສະວິດເປີດໃຊ້ງານ ແລະ I/O Harness
ສະຖານະພາບ LED

22-Pin (ການເຊື່ອມຕໍ່ພະລັງງານ / ຂໍ້ມູນ)
Dip Switch bank (ທາງເລືອກ)

USB (ການອັບເດດ/ຂໍ້ມູນຊອບແວ)

ປຸ່ມກົດ 12-PIN I/O ສາຍຮັດ

ZW-GM Operation: 1. Install the Z-WAGZ unit to the OE BCM unit. Follow instructions on page 3 for all vehicles. 2. Turn Ignition ON (Ignition must be on for proper operation). Leave vehicle in Park. 3. To activate Z-WAGZ: o Press and HOLD the high beam lever (5 sec) OR o Press and HOLD the provided push button (3 sec) OR o Send a latched 12v (+) signal to the blue wire (designed to be extended for OE up-fitter switches) NOTE: if using this method to activate, then the only way to deactivate is removing power from the input (or shutting truck down fully)
ຮູບແບບທີ 1 ຈະເລີ່ມກະພິບ. ເມື່ອຮູບແບບທີ 1 ເລີ່ມຕົ້ນ, ອັນຕະລາຍໃນກຸ່ມເຄື່ອງວັດແທກຈະກະພິບ 1 ເທື່ອ, ສະແດງໃຫ້ເຫັນວ່າຮູບແບບ 1 ໄດ້ຖືກເລືອກແລ້ວ ແລະ ໄຟ LED ໃນເຄື່ອງຈະກະພິບເປັນສີຟ້າ. ເບິ່ງຕາຕະລາງສໍາລັບການຊີ້ບອກສີຮູບແບບທີ່ຍັງເຫຼືອ.
4. ເພື່ອສະຫຼັບໄປໃຊ້ຮູບແບບທີ 2: (ຮູບແບບທີ 1 ຈະຕ້ອງເປີດຢູ່ໃນຂະນະນີ້) o ເຊື່ອມຕໍ່ໄຟລ້ຽວ, ຈາກນັ້ນກົດ ແລະ ກົດປຸ່ມເບົ້າໄຟສູງຄ້າງໄວ້ອີກຄັ້ງ (5 ວິນາທີ). ຫຼື o ກົດ & ປ່ອຍປຸ່ມກົດທີ່ສະຫນອງໃຫ້
ອັນຕະລາຍຈະກະພິບສອງເທື່ອສະແດງວ່າຮູບແບບ 2 ໄດ້ຖືກເລືອກແລ້ວ. ເຮັດຊ້ໍາຂະບວນການນີ້ເພື່ອສະຫຼັບກັບຮູບແບບຕໍ່ໄປ.
5. ເພື່ອປິດການນຳໃຊ້ Z-WAGZ: o ກົດປຸ່ມສາຍໄຟສູງຄ້າງໄວ້ ຫຼື o ກົດຄ້າງໄວ້ທີ່ປຸ່ມກົດທີ່ໃຫ້ໄວ້ ຫຼື o ປ່ອຍສັນຍານ 12v (+) ໄປຫາສາຍສີຟ້າ (ຖ້າເຊື່ອມຕໍ່ດ້ວຍວິທີນີ້)
PLOW MODE ຈະເຮັດໃຫ້ຮູບແບບທີ່ເລືອກໃນປັດຈຸບັນຊ້າລົງ, ແລະປິດການເປີດສາຍສູງ ແລະຕ່ຳບໍ່ໃຫ້ກະພິບ. ເມື່ອ INPUT 2 (violet) ໄດ້ຮັບ 12v (+) ກ່ອນທີ່ຈະເປີດໃຊ້ flasher, PLOW MODE ຖືກເປີດໃຊ້.

· Vehicles equipped with LED lights should use LED patterns. Vehicles equipped with standard bulbs should use bulb patterns.
· Not all lights on the vehicle are necessarily used, some lights are not controllable via BCM CAN data. · Z-WAGZ will retain the last used pattern, even after being disconnected from the BCM (if ever). · When flashing is active: turn signals, headlights & reverse lights will override pattern flashing, until turned off
again. · When on some patterns, in some vehicles, the reverse camera image may show up/flash on the OE screen (if
equipped). This is a factory limitation and is normal. If you want to avoid this, keep DIP (3) OFF. · For GM trucks, OE fog lights are typically wired together (and therefore only flash together) · If vehicle is equipped with physical actuators that activate for high beams/low beams, ZZ2 highly suggests disabling
that beam from flashing (otherwise mechanical failure may occur quickly) · `Plow Mode’, when active (INPUT 2), disables High & Low beam flashing and slows the pattern down so that the
relay box (plow module) can keep up with the flashing (prevents overheating).

1080 Holland Drive, Boca Raton, FL 33487 | 929-220-1212

2|ໜ້າ

1. Locate the BCM unit. The chart below indicates the BCM location in various vehicles.
2. With the vehicle OFF, driver door open (5 mins): disconnect the (4) highlighted plugs shown. Connect the male side of each T-Harness to the BCM and the (removed) plugs into the female side of the Z-WAGZ BCM harnessing. These connectors can only fit in one place and connect in one way and are color matched to the OE plugs.
3. Connect the ZW-GM module LAST to the 22-pin connector, tie-wrap the unit to another harness if desired.
4. ກັບຄືນໄປຫາຫນ້າ (2) ສໍາລັບຄໍາແນະນໍາການດໍາເນີນງານ.

MODEL Silverado/Sierra/Colorado

LOCATION Underneath steering
wheel / dash area

ເຮັດ
GM

MODEL Silverado / Sierra Colorado / Canyon
Silverado Sierra 2500/3500 HD
ທາໂຮ/ຊານເມືອງ

YEAR 2014- 2022.5 2018-2022.5
2014-2022.5
2018-2020

*`Plow Mode’, when active (INPUT 2), disables High & Low beam flashing and slows the pattern down so that the relay box (plow
module) can keep up with the flashing (prevents overheating). This should be enabled whenever a plow is connected.

ໂມດູນຄວບຄຸມຮ່າງກາຍ OE GM

1080 Holland Drive, Boca Raton, FL 33487 | 929-220-1212

3|ໜ້າ

ຕັ້ງຢູ່ດ້ານຫລັງຂອງຫນ່ວຍບໍລິການແມ່ນທະນາຄານຂອງ (6) ຫຼັບ dip ທ່ານຈະຈໍາເປັນຕ້ອງໄດ້ເລືອກເອົາເຄື່ອງມືເພື່ອປັບ.

ທຸກໆປຸ່ມ dip ແມ່ນ LIVE, ຢ່າຖອດໂມດູນເພື່ອປັບ.

DIP 1

ປິດການໃຊ້ງານ

ເປີດໃຊ້ Reverse Light

For HALOGEN Disable STROBE Mode Heated seat

ON High Low (May cause reverse camera to equipped (Removes strobe every issue only:

Beam Beam ສະແດງໃຫ້ເຫັນໃນຫນ້າຈໍໃນຂະນະທີ່ການເຄື່ອນໄຫວ) (ຊ້າລົງ)

3 ວິນາທີ)

ເປີດ*

ເປີດໃຊ້ Enable OFF High Low
ບີມ ບີມ

ປິດການໃຊ້ງານ Reverse Light

ສໍາລັບອຸປະກອນ LED (ໄວກວ່າ)

ເປີດໃຊ້ໂໝດ STROBE

ໂດຍປົກກະຕິໃຫ້ປິດການເລີ່ມຕົ້ນ

Software v1.6 NOTES:
– When turn off ACC the unit will deactivate (stop flashing) – If reverse camera flashes/displays on radio screen when flashing is active, keep DIP 3 off (reverse will no longer flash) – If starting the vehicle via remote start and then flasher unit is activated (before true ignition), the vehicle will shut down. – High Beam Lever / External Button / INPUT 1 +12V trigger:
Some vehicles require the engine to be running to activate flashing (seen in a 2022 vehicle), others only require IGN ON to activate – Brake priority not supported on all vehicles
– *If heated seats do not function (while unit is active), try turning ON DIP 6. NOTE: in some vehicles, this will prevent normal function of
the unit, if that’s the case, leave DIP 6 OFF (this vehicle has a limitation for filtering certain commands at the BCM and making lights flash).
– Strobe mode is disabled automatically if the vehicle has limitations with turn signal commands – When using wire trigger to turn ON unit flashing, the unit cannot be deactivated by any other method, use wire trigger to turn off as well

1080 Holland Drive, Boca Raton, FL 33487 | 929-220-1212

4|ໜ້າ

ຕົວຊີ້ວັດການເລີ່ມຕົ້ນ

Description Initial Wake Up Unit recognizes CAN bus (car side ONLY) Unit recognizes CAN bus (module side ONLY) Unit recognizes CAN bus (properly)
Unit detects ACC info Unit detects GEAR info Unit detects HIGH BEAM pull OR External button press
(for activation) Unit receives negative response for light commands Unit not receiving confirmation for light commands
When unit goes to sleep CAN bus communication problem

LED Status Blinks BLUE (1 time) Blinks BLUE (3 times) Blinks GREEN (3 times) Binks BLUE,GREEN
(x3) Blinks GREEN (1 time) Blinks VIOLET (1 time)
ສີຂຽວແຂງ
Blinks VILOET (x3) Blinks RED (x1)
ກະພິບສີຂາວ (x1) ກະພິບສີແດງ + ສີຂຽວ

ຕົວຊີ້ບອກຮູບແບບ

ຂໍ້ມູນເພີ່ມເຕີມກ່ຽວກັບການເຊື່ອມຕໍ່ພະລັງງານເບື້ອງຕົ້ນ
Upon CAN data wake Upon CAN data wake Upon CAN data wake
ເມື່ອເປີດເຄື່ອງຕິດໄຟ ເມື່ອປ່ຽນເກຍ
ເມື່ອກົດປຸ່ມ High Beam lever ຫຼືປຸ່ມກົດທີ່ສະຫນອງໃຫ້
–Contact ZZ2—Contact ZZ2–
-While Z-WAGZ is activated

Description Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6

LED Status Blinks BLUE Blinks GREEN Blinks RED Blinks LIGHT BLUE Blinks VIOLET Blinks YELLOW

ຂໍ້ມູນເພີ່ມເຕີມຮູບແບບພື້ນຖານ
WATERFALL PATTERN DOUBLE BLINK PATTERN (double back & forth) SINGLE BLINK PATTERN (single back & forth) SINGLE BLINK PATTERN (NO RED FLASH ON REAR) SINGLE BLINK PATTERN (NO CARGO LIGHT FLASH)

ການບໍລິໂພກພະລັງງານ / ລາຍລະອຽດເພີ່ມເຕີມ

ລາຍລະອຽດໃນປັດຈຸບັນ Draw Active:
Current Draw idle: INPUT 1 Trigger wire act:
Output 1: 12v (+) OUTPUT 2 (ຂວາ): 12v (+) OUTPUT 3 (ຊ້າຍ): 12v (+)
Trigger wire idle: ຂີດຈຳກັດປັດຈຸບັນ:

ຂໍ້ມູນຈໍາເພາະ 100mA ສູງສຸດ
7mA max 12V (+) 100mA max 100mA max 100mA max
3.3V 10mA

ຂໍ້ມູນເພີ່ມເຕີມ
Hardwire activation trigger Outputs 12v (+) whenever unit is active
Mimics RIGHT turn signal pattern Mimics LEFT turn signal pattern

1080 Holland Drive, Boca Raton, FL 33487 | 929-220-1212

5|ໜ້າ

ແສງສະຫນັບສະຫນຸນ beams ຕ່ໍາ
Front Turn Signals High Beams Fog Lights
Driver Running Lights (DRL) Mirror Turn Signal Lights Mirror Task Lights Cab Lights (read notes)
ແສງສະຫນັບສະຫນຸນ 3rd Brake Lights Brake Lights Rear DRLs
ສັນຍານການລ້ຽວດ້ານຫຼັງ ໄຟປີ້ນ
Bed Lights (cargo) License Plate Lights Left/Right Trailer Turn signals
ໄຟນໍ້າຖ້ວມ

ໄຟໜ້າ

DIP PARAMETER

ໝາຍເຫດ

Dip ປັບໄດ້

—

ບໍ່ມີ

—

Dip ປັບໄດ້

—

ບໍ່ມີ

—

ບໍ່ມີ

—

ບໍ່ມີ

—

ບໍ່ມີ

ຂຶ້ນກັບຕົວແບບ

ບໍ່ມີ

Not supported the signal for these is not driven by

the BCM/LCM, it’s directly powered from the switch.

ໄຟຫຼັງ

DIP PARAMETER

ໝາຍເຫດ

ບໍ່ມີ

ຕິດຕັ້ງສູງກາງ

ບໍ່ມີ

—

ບໍ່ມີ

—

ບໍ່ມີ

—

Dip ປັບໄດ້

—

ບໍ່ມີ

ແຂງ ON ເມື່ອຮູບແບບ 6 ຖືກໃຊ້

ບໍ່ມີ

—

ບໍ່ມີ

ບໍ່ຮອງຮັບໃນທຸກລຸ້ນ

ບໍ່ມີ

*NOTE: As new variants of vehicles are released over time, some lights may not flash due to manufacturer design changes (software or the wiring to the housings
themselves). The chart above is accurate for vehicles the ZW-GM was tested on.

1080 Holland Drive, Boca Raton, FL 33487 | 929-220-1212

6|ໜ້າ

ເອກະສານ / ຊັບພະຍາກອນ

Z WAGZ ZW-GM Advanced Plug andPlay Module Integration Designed [pdf] ຄູ່ມືການສອນ
ZZ-2, ZW-GM Advanced Plug andPlay Module Integration Designed, ZW-GM, Advanced Plug andPlay Module Integration Designed, andPlay Module Integration, Module Integration, Integration

ເອກະສານອ້າງອີງ

ຄູ່ມືຜູ້ໃຊ້

Z WAGZ ZW-GM Advanced Plug andPlay Module Integration ຄູ່ມືການສອນທີ່ອອກແບບມາ

ZW-GM Advanced Plug andPlay Module ປະສົມປະສານອອກແບບ

ຂໍ້ມູນຈໍາເພາະຂອງຜະລິດຕະພັນ:

ຄໍາແນະນໍາການນໍາໃຊ້ຜະລິດຕະພັນ:

ການຕິດຕັ້ງ:

ການດໍາເນີນງານ:

ຄຳຖາມທີ່ຖາມເລື້ອຍໆ (FAQ):

Q: What vehicles are compatible with the ZW-GM module?

Q: How can I enable ‘Plow Mode’?

ເອກະສານ / ຊັບພະຍາກອນ

ເອກະສານອ້າງອີງ

ອອກຄໍາເຫັນ

ຍົກເລີກການຕອບ