ແນະນຳ
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Ikea KALLROR 503.570.02 Stainless Steel Cabinet Handles. Please read these instructions carefully before proceeding with installation to ensure proper and safe use.
ສິນຄ້າເກີນview
The Ikea KALLROR 503.570.02 handles are designed to offer a modern aesthetic and functional grip for your kitchen cabinets or drawers. This set includes two handles and all necessary screws for a complete installation.
This image displays two sleek, cylindrical stainless steel cabinet handles, along with four silver screws. The handles have a brushed finish, and each handle is shown with two mounting posts. The screws are designed to secure the handles to cabinet doors or drawers.
ຂໍ້ມູນຈໍາເພາະ
| ໝາຍເລກຕົວແບບ | 503.570.02 |
| ຍີ່ຫໍ້ | Ikea |
| ຈຳນວນຕໍ່ຊຸດ | ມືຈັບ 2 ອັນ |
| ຄວາມຍາວຂອງມື | 213 ມມ |
| ຈັບຄວາມເລິກ | 38 ມມ |
| Hole Spacing (center-to-center) | 160 ມມ |
| Drilled Hole Diameter | 5 ມມ |
| ຄວາມຫນາຂອງປະຕູທີ່ເຫມາະສົມ | 16 ມມ ຫາ 21 ມມ |
| Handle/End Cap Material | ສະແຕນເລດ |
| Plastic Parts Material | ພາດສະຕິກ Polyethylene |
| ອົງປະກອບລວມ | ອຸປະກອນຕິດຕັ້ງ (ສະກູ) |
| ນ້ຳໜັກ | 170 ກຣາມ |
ການຕິດຕັ້ງແລະການຕິດຕັ້ງ
Installing your Ikea KALLROR cabinet handles is a straightforward process. Follow these steps carefully for a secure attachment.
ເຄື່ອງມືທີ່ຈໍາເປັນ
- ເຈາະ
- Drill bit (5 mm diameter)
- ເທບວັດແທກຫຼືໄມ້ບັນທັດ
- ສໍ
- Screwdriver (ຫົວ Phillips ແນະນໍາ)
ຂັ້ນຕອນການຕິດຕັ້ງ
- ການວັດແທກແລະເຄື່ອງຫມາຍ: Carefully measure and mark the desired position for the handle on your cabinet door or drawer front. Ensure the marks for the two screw holes are precisely 160 mm apart (center-to-center).
- ຮູເຈາະ: Using a 5 mm drill bit, carefully drill through the cabinet door or drawer front at the marked positions. Ensure the holes are straight and clean.
- ຄັດຕິດ Handle: Align the handle with the drilled holes. Insert the provided screws from the inside of the cabinet door or drawer through the drilled holes and into the handle posts.
- ມືຈັບທີ່ປອດໄພ: Tighten the screws firmly with a screwdriver until the handle is securely attached. ບໍ່ overtighten, as this may damage the cabinet material.
- ເຮັດຊ້ຳ: Repeat the process for the second handle if installing a set.
Important: These handles are suitable for door thicknesses between 16 mm and 21 mm. Verify your cabinet door thickness before drilling.
ການດໍາເນີນງານ
The Ikea KALLROR cabinet handles are designed for simple and reliable operation. Grasp the handle firmly to open or close cabinet doors and drawers as needed.
ບໍາລຸງຮັກສາ
To ensure the longevity and appearance of your stainless steel handles, follow these maintenance guidelines:
- ທໍາຄວາມສະອາດ: Wipe regularly with a soft, damp cloth. For stubborn marks, use a mild detergent solution. Avoid abrasive cleaners, scouring pads, or chemical solvents, as these can damage the stainless steel finish.
- ການອົບແຫ້ງ: Always dry the handles thoroughly after cleaning to prevent water spots and maintain their luster.
- ການກວດກາ: Periodically check the screws for tightness. If a handle feels loose, gently tighten the screws with a screwdriver.
ການແກ້ໄຂບັນຫາ
Handle is Loose
If the handle feels loose, gently tighten the screws from the inside of the cabinet door or drawer. Ensure not to overtighten.
ຄວາມຫຍຸ້ງຍາກໃນການຕິດຕັ້ງ
Ensure the drilled holes are precisely 160 mm apart (center-to-center) and that the drill bit used was 5 mm in diameter. Verify your cabinet door thickness is within the specified 16-21 mm range.
ສະຫນັບສະຫນູນ
For further assistance or inquiries regarding your Ikea KALLROR cabinet handles, please refer to the official Ikea webຫຼື ຕິດຕໍ່ບໍລິການລູກຄ້າ Ikea ໂດຍກົງ.
