QCS403YA Datasheet
USER’S MANUAL
QCS403YA44 with WCN3980 1×1 11ac/BT5.1 connectivity LGA
System-on-Module (SOM)
QCS403YA44
Memory Configuration: MCP 512MB+512MB
Version 1.7
Internet Communication Module S.B.U
LITE-ON Technology Corporation
11F, 392, Ruey Kuang Road,
Neihu, Taipei 11492, Taiwan, R.O.C.
1.2 INTRODUCTION
The QCS403YA device is an Audi/Wi-Fi SoC for use in the smart Speaker, Smart Assistant, Mesh router and Soundbar markets. It includes a 64-bit ARM Cortex-A53 dual-core application processor.
1.3 QCS403YA FEATURES
- MCP Memory Support (1×32 LPDDR2 32-bit wide memory support for up to 533MHz + SLC NAND Flash)
- 12 channel/384kHz; 32 channel/192kHz; DSD support
- Direct 8x PDM DMIC support
- Support for UART, I2C, SPI, USB2.0 interface
- Support for high fidelity CSRA6620/6640 amplifiers (optional)
1.4 QCS403YA SPECIFICATIONS
| Feature | Specification |
| Processor | QCS403-0 ARM Cortex-A53 microprocessor cores
|
| Memory |
Nanya(PVL) and ESMT(Under Qualification) are the alternates each other |
| DSP | Audio DSP (800MHz, Quad MAC) 1.5MB Compute DSP(700MHz, Dual MAC), 256K |
| Wireless | WCN3980 – 802.11a/b/g/n/ac – 1×1 MU-MIMO – 2.4/5GHz – Bluetooth 5.1; aptXSee Appendix for detail |
| Machine Learning | HVX accelerator for improved ECNS, wake-word detection and local ASR |
| Audio Decode | MP3, AAC, ALAC, FLAC, He-AAC v1/v2, WMA 9/Pro |
| Voice | 6-mic Fluence PRO w/Linear Echo Cancellation(LEC) CNN based SVA; Hexagon Vector Extension(HVX) |
| Audio Interface | 1x SLIMbus interface to WCD9335(optional) 3x I2S TDM (384kHz/32bit) 8x DMIC |
| Power Management | Power management (PMS405) |
| I/O | 1x USB2.0 interface,1x SPDIF, 2x UART, 2x SPI, 3x I2C |
| OS Support | Linux based |
| SOM Dimension | 37x37mm |
| Antenna Type | 1x I-PEX antenna connector; Wi-Fi & BT share the same antenna |
| Operating Environment | Power Input: 3.6V Operating Temperature: 0ºC to +65ºC |
1. SOM PHOTO
TOP SIDE
BOTTOM SIDE
2. ELECTRICAL SPECIFICATIONS
10.1 Absolute maximum ratings
Table 10-1 Absolute maximum ratings
| Power supply | Description | Min | Typ | Max | Units |
| VPH_PWR | Prime Power | -0.5 | – | 5.25 | V |
| VDD_CH0_3P3 | Power supply for WCN3980 from system | -0.3 | – | 3.63 | V |
| VREG_L4_1P2 | Linear regulator L4 output for QCS403 | -0.3 | – | 1.7 | V |
| VREG_L6_1P8 | Linear regulator L6 output for QCS403, WCN3980, Memory | -0.3 | – | 2.3 | V |
| VREG_L12_3P3 | Linear regulator L12 output for QCS403 | -0.3 | – | 3.8 | V |
| VREG_L11_SDC2 | Linear regulator L11 output for QCS403 | -0.3 | – | 3.4 | V |
| VREG_S4_1P8 | Linear regulator S4 output | -0.3 | – | 2.3 | V |
10.2 Operation Conditions
Table 10-2 Recommended Operation Conditions
| Symbol | Parameter | Min | Typ | Max | Units |
| VPH_PWR | Prime Power | 2.5 | 3.6 | 5.25 | V |
| VDD_CH0_3P3 | Power supply for WCN3980 from system | 2.97 | 3.3 | 3.63 | V |
| VREG_L4_1P2 | Linear regulator L4 output for QCS403 | 1.144 | 1.2 | 1.256 | V |
| VREG_L6_1P8 | Linear regulator L6 output for QCS403, WCN3980, Memory | 1.704 | 1.8 | 1.896 | V |
| VREG_L12_3P3 | Linear regulator L12 output for QCS403 | 2.97 | 3.3 | 3.63 | V |
| VREG_L11_SDC2 | Linear regulator L11 output for QCS403 | 2.7 | 2.95 | 3.05 | V |
| VREG_S4_1P8 | Linear regulator S4 output | 1.704 | 1.8 | 1.896 | V |
| TA | Ambient operating temperature | 0 | 25 | 65 | C |
| TS | Storage temperature | -20 | 25 | 80 | C |
APPENDIX – WCN3980 1X1 WIRELESS CONNECTIVITY SPECIFICATIONS
Table A-1 Bluetooth specifications
| BT Function | |
| Standard | Bluetooth V5.1LE |
| Data Rate | 1 Mbps, 2Mbps and Up to 3Mbps |
| Modulation Scheme | GFSK, π/4-DQPSK and 8-DPSK |
| Frequency Range | 2.402~2.480 GHz |
| Transmit Output Power | +4 ≤ Output Power ≤ +10dBm; Class I Device |
| Receiver Sensitivity | < 0.1% BER at -94dBm |
Table A-2 Wi-Fi specifications
| Wi-Fi Function | |
| Standard | IEEE802.11a; IEEE802.11b; IEEE 802.11g; IEEE 802.11n; IEEE802.11ac |
| Data Rate | 802.11a: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11b: 11, 5.5, 2, 1 Mbps 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: MCS 0 to 7 for HT20MHz MCS 0 to 7 for HT40MHz 802.11ac: MCS 0 to 8 for HT20MHz MCS 0 to 9 for HT40MHz MCS 0 to 9 for HT80MHz |
| Media Access Control | CSMA/CA with ACK |
| Modulation Technique | 802.11a: 64QAM, 16QAM, QPSK, BPSK 802.11b: CCK, DQPSK, DBPSK 802.11g: 64QAM, 16QAM, QPSK, BPSK 802.11n: 64QAM, 16QAM, QPSK, BPSK 802.11ac: 256QAM, 64QAM, 16QAM, QPSK, BPSK |
| Network Architecture | Infrastructure mode |
| Operation Channel | 2.4GHz 11: (Ch. 1-11) – United States 13: (Ch. 1-13) – Europe 14: (Ch. 1-14) – Japan 5GHz 21: USA 19: EU 8: Japan |
| Frequency Range | 802.11bg 2.400 ~ 2.4835 GHz 802.11a 5.15 ~ 5.85 GHz |
| Security | WPS, WPA, WPA2, WEP 64bit & 128bit, IEEE 802.1X, IEEE 802.11i |
Table A-3 Transmit Output Power specifications
2.4GHz
Transmit Output Power Tolerance: ±1.5dBm
| 802.11b | 1Mbps | 2Mbps | 5.5Mbps | 11Mbps |
| Tgtpwr (dBm) |
16 | 16 | 16 | 16 |
| 802.11g | 6~24Mbps | 36Mbps | 48Mbps | 54Mbps |
| Tgtpwr (dBm) |
16.5 | 16 | 15 | 13.5 |
| 802.11n
HT20 |
MCS0 | MCS1 | MCS2 | MCS3 | MCS4 |
| Tgtpwr (dBm) |
16.5 | 16.5 | 16.5 | 16 | 16 |
| MCS5 | MCS6 | MCS7 | |||
| 15 | 14 | 13.5 |
| 802.11n
HT40 |
MCS0 | MCS1 | MCS2 | MCS3 | MCS4 |
| Tgtpwr (dBm) |
15.5 | 15.5 | 15.5 | 15 | 15 |
| MCS5 | MCS6 | MCS7 | |||
| 14 | 13 | 12.5 |
5GHz
Transmit Output Power Tolerance: ±2dBm
| 802.11a | 6~24Mbps | 36Mbps | 48Mbps | 54Mbps |
| Tgtpwr (dBm) |
15.5 | 14 | 13 | 12 |
| 802.11n HT20 |
MCS0 | MCS1 | MCS2 | MCS3 | MCS4 |
| Tgtpwr (dBm) |
15.5 | 15.5 | 15.5 | 15 | 15 |
| MCS5 | MCS6 | MCS7 | |||
| 14 | 13 | 12 |
| 802.11n HT40 |
MCS0 | MCS1 | MCS2 | MCS3 | MCS4 |
| Tgtpwr (dBm) |
14.5 | 14.5 | 14.5 | 14 | 14 |
| MCS5 | MCS6 | MCS7 | |||
| 13 | 12 | 11 |
| 802.11ac VHT80 | MCS0 | MCS1 | MCS2 | MCS3 | MCS4 |
| Tgtpwr (dBm) |
13.5 | 13.5 | 13.5 | 13 | 13 |
| MCS5 | MCS6 | MCS7 | MCS8 | MCS9 | |
| 12 | 11 | 10 | 9 | 8 |
Table A-4 Receiver Sensitivity specifications
| Frequency Band | Rate | Condition | 1×1(1SS) (dBm) |
|
2.4G |
11b-1M | PER < 8% | -95 |
| 11b-11M | PER < 8% | -87 | |
| 11g-6M | PER < 10% | -90 | |
| 11g-54M | PER < 10% | -72 | |
| 11ac-VHT20MCS0 | PER < 10% | -89 | |
| 11ac-VHT20MCS7 | PER < 10% | -70 | |
| 11ac-VHT20MCS8 | PER < 10% | -68 | |
| 11ac-VHT40MCS0 | PER < 10% | -87 | |
| 11ac-VHT40MCS7 | PER < 10% | -67 | |
| 11ac-VHT40MCS8 | PER < 10% | -65 | |
| 11ac-VHT40MCS9 | PER < 10% | -63 | |
|
5G |
11a-6M | PER < 10% | -87 |
| 11a-54M | PER < 10% | -71 | |
| 11ac-VHT20MCS0 | PER < 10% | -87 | |
| 11ac-VHT20MCS7 | PER < 10% | -70 | |
| 11ac-VHT20MCS8 | PER < 10% | -66 | |
| 11ac-VHT40MCS0 | PER < 10% | -84 | |
| 11ac-VHT40MCS7 | PER < 10% | -67 | |
| 11ac-VHT40MCS9 | PER < 10% | -61 | |
| 11ac-VHT80MCS0 | PER < 10% | -81 | |
| 11ac-VHT80MCS7 | PER < 10% | -65 | |
| 11ac-VHT80MCS9 | PER < 10% | -57 |
WARNINGS
FCC Statement:
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
This device and its antenna(s) must not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures.
Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without C2P.
This device is restricted for indoor use.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.
IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated.
Additional testing and certification may be necessary when multiple modules are used.
20 cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to
also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
This device is restricted to indoor use.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following ” Contains FCC ID: PPQ-QCS403YA”. If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
This module is certified pursuant to Part 15 rules section 15.247, 15.407 and RSS-247.
This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated.
| Antenna | Frequency Band | Antenna Type | Brand | Model Number | Gain(dBi) |
| 1 | 2400-2483.5MHz;BT | PIFA | INPAQ | RFPCA370808IMLB302 | 2.55 |
| 5150-5850MHz | 4.87 | ||||
| 2 | 2400-2483.5MHz;BT | PIFA | INPAQ | RFPCA370811IMLB301 | 2.4 |
| 5150-5850MHz | 4.56 | ||||
| 3 | 2400-2483.5MHz; BT | PIFA | INPAQ | RFPCA370838IMLB302 | 2.02 |
| 5150-5850MHz | 5.46 | ||||
| 4 | 2400-2483.5MHz; BT | PIFA | INPAQ | RFPCA320808IMAB301 | 2.5 |
| 5 | 2400-2483.5MHz; BT | PIFA | INPAQ | RFPCA320806IMAB302 | 2.5 |
Information on test modes and additional testing requirements
This module has been approved under stand-alone configuration.
OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band.
The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093/RSS-102 and different antenna configurations
The information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, versus with multiple, simultaneously transmitting modules or other transmitters in a host can be found at KDB Publication 996369 D04.
OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC/ISED authorization is no longer considered valid and the FCC/IC No. cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC/ISED authorization.
Additional testing, Part 15 Subpart B and ICES-003 disclaimer
Appropriate measurements (e.g. Part 15 Subpart B compliance) and if applicable additional equipment authorizations (e.g. SDoC) of the host product to be addressed by the integrator/manufacturer.
This module is only FCC/ISED authorized for the specific rule parts 15.247, 15.407/RSS-247 listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC/ISED rules that apply to the host product as being Part 15 Subpart B/ICES-003 compliant.
IC Statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
This device and its antenna(s) must not be co-located with any other transmitters except in accordance with IC multi-transmitter product procedures.
Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without reassessment permissive change.
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate.
Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 5650-5725 MHz.
The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit.
Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
For indoor use only.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.
This radio transmitter (IC: 4491A-QCS403YA) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
The transmitter module may not be co-located with any other transmitter or antenna.
This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module.
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to
also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The transmitter module may not be co-located with any other transmitter or antenna.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following ” Contains IC : 4491A-QCS403YA”.
The user manual of the end product should include:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
1.This device may not cause interference.
2.This device must accept any interference, including interference that may cause undesired operation of the device.
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
ISED Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
Table for Filed Antenna
|
Antenna |
Frequency Band | Antenna Type | Brand | Model Number |
Gain(dBi) |
|
1 |
2400-2483.5MHz;BT | PIFA | INPAQ | RFPCA370808IMLB302 | 2.55 |
| 5150-5850MHz |
4.87 |
||||
|
2 |
2400-2483.5MHz;BT | PIFA | INPAQ | RFPCA370811IMLB301 | 2.4 |
| 5150-5850MHz |
4.56 |
||||
|
3 |
2400-2483.5MHz; BT | PIFA | INPAQ | RFPCA370838IMLB302 | 2.02 |
| 5150-5850MHz |
5.46 |
||||
|
4 |
2400-2483.5MHz; BT | PIFA | INPAQ | RFPCA320808IMAB301 | 2.5 |
| 5 | 2400-2483.5MHz; BT | PIFA | INPAQ | RFPCA320806IMAB302 |
2.5 |
CE Statement:
This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.
Japan Statement:
5GHz product for indoor use only.
Documents / Resources
 |
LITE ON QCS403YA Internet Communication Module [pdf] User Manual QCS403YA, PPQ-QCS403YA, PPQQCS403YA, Wireless Module, Internet Communication Module, QCS403YA Internet Communication Module |
