CCD-0002160 Slide Track
“
Specifications
- Product: Slide Track
- Functionality: Allows a seat to slide from front-to-back and
lock in a fixed position - Manufacturer: OEM
Product Usage Instructions
Installation
- Turn over the seat frame so the underside is accessible.
- Insert slide track bolts into the appropriate seat frame
holes. - Ensure the upper track is placed against the frame, while the
lower track faces the installer. - Place the track with the latch on the side of the seat where
the handle will be located. - Install a 5/16 washer and flange nut on the upper track bolts
and finger-tighten the nuts. Use a washer as a spacer for each
slide track fastener to prevent binding during operation. - Install the X-frame alignment tool to keep slide tracks
parallel and square to one another. Keep the tool in place until
installation and testing are completed. - Firmly tighten the nuts on the upper track bolts.
FAQ
Q: What should I do if the slide track bolts do not fit
properly?
A: If the slide track bolts do not fit properly, contact the
manufacturer for assistance in obtaining the correct bolts for your
specific application.
Q: Is it necessary to wear safety equipment during
installation?
A: Yes, it is recommended to wear safety equipment such as eye
protection, hearing protection, gloves, and possibly a full face
shield to prevent injury during installation, service, or
maintenance.
“`
Slide Track
OEM INSTALLATION MANUAL
TABLE OF CONTENTS
Introduction
2
Safety
2
Resources Required
2
Installation
3
Introduction
This manual describes installation of seat slide tracks, a horizontally-mounted assembly that allows a seat to slide from front-to-back and then lock in a fixed position. For additional support on this product, please visit: https://support.lci1.com/seating-structures-andmechanisms
NOTE: Images used in this document are for reference only when assembling, installing and/or operating this product. Actual appearance of provided and/or purchased parts and assemblies may differ.
Safety
Read and understand all instructions before installing or operating this product. Adhere to all safety labels. This manual provides general instructions. Many variables can change the circumstances of the instructions, i.e., the degree of difficulty, operation and ability of the individual performing the instructions. This manual cannot begin to plot out instructions for every possibility, but provides the general instructions, as necessary, for effectively interfacing with the device, product or system. Failure to correctly follow the provided instructions may result in death, serious personal injury, severe product and/or property damage, including voiding of the Lippert limited warranty.
The “WARNING” symbol above is a sign that an installation procedure has a safety risk involved and may cause death, serious personal injury or severe product and/or property damage if not
performed safely within the parameters set forth in this manual.
Failure to follow the instructions provided in this manual may result in serious injury, damage or voiding of the product warranty. Always wear eye protection when performing installation, service
or maintenance. Other safety equipment to consider would be hearing protection, gloves and possibly a full face shield, depending on the nature of the service.
The “CAUTION” symbol above is a sign that a procedure has a risk involved that may cause personal injury and/or product damage if not performed safely and within the parameters set forth within this manual.
Moving parts can pinch, crush or cut. Keep clear and use caution.
Resources Required
· Cordless or electric drill or screw gun · Appropriate drive bits · Needle-nose pliers
Rev: 07.27.25
· X-frame alignment tool (See Note)
· 5/16″ washers · 5/16″ flange nuts
Page 2
CCD-0002160
NOTE: To receive the proper X-frame alignment tool, contact Lippert. Lippert can fabricate an X-frame alignment tool based on dimensions detailed by the OEM, including measurements from center-tocenter of the bolts used for the particular application. Alternatively, the OEM can create a X-frame alignment tool from instructions provided by Lippert, including recommended material to be used for the tool.
Installation
1. Turn over seat frame so the underside is accessible. 2. Insert slide track bolts into the appropriate seat frame holes (Fig. 1).
NOTE: The assembly’s upper track should be placed against the frame, while the lower track should face the installer (Fig. 2).
NOTE: Bolt length varies as to application and OEM need.
3. Place the track with the latch on the side of the seat where the handle will be located (Fig. 1).
Fig. 1
Latch
Other Seat Frame Holes
Track Bolts Installed
In Seat Frame
Rev: 07.27.25
Fig. 2
Lower Track
Lower Track
Upper Track
Upper Track Page 3
CCD-0002160
4. Install a 5/16″ washer and flange nut on the four upper track bolts (Fig. 3) and finger-tighten the nuts.
NOTE: A washer to function as a spacer is required for every slide track fastener, including those on both upper and lower tracks. The spacer prevents the slide track from binding during operation.
Fig. 3
Washer and Flange Nut
Washer and Flange Nut
5. Install the X-frame alignment tool (Fig. 4) to keep slide tracks parallel and square to one another. Place tool over the four bolts on the lower tracks (Fig. 5).
NOTE: Keep alignment tool in place until installation and testing is completed. 6. Firmly tighten the four nuts on the upper track bolts (Fig. 3).
Fig. 4
Track Bolts
Rev: 07.27.25
Fig. 5
Track Bolts
Page 4
CCD-0002160
7. Using needle-nose pliers, remove the spring from the latch (Fig. 6). NOTE: Frame removed from latch image for clarity.
Fig. 6
Spring
8. Test the operation of the slide tracks by repeatedly sliding them up and down. 9. Replace spring on the latch. 10. Remove X-frame alignment tool.
Rev: 07.27.25
Page 5
CCD-0002160
The contents of this manual are proprietary and copyright protected by Lippert. Lippert prohibits the copying or dissemination of portions of this manual unless prior written consent from an authorized Lippert representative has been provided. Any unauthorized use shall void any applicable warranty. The information contained in this manual is subject to change without notice and at the sole discretion of Lippert. Revised editions are available
for free download from lippert.com.
Please recycle all obsolete materials.
For all concerns or questions, please contact Lippert Ph: 432-LIPPERT (432-547-7378) | Web: lippert.com | Email: customerservice@lci1.com
Documents / Resources
 |
LiPPERT CCD-0002160 Slide Track [pdf] Instruction Manual CCD-0002160 Slide Track, CCD-0002160, Slide Track, Track |