W712 Digital Intercom Gateway
User Manual

Package Contents

Physical specification

Device size 126*209*26.3mm
1) Panel

 Interface description
The interface on the back of the device can be used for power supply, network, TF card, U disk, etc. The connection is shown as follows:

Installation

Step 1: Installation preparation
A. Power Supply check
Check whether the voltage of dc power supply or external power supply in the range of the working voltage of the product(12V/2A).
B. Product Check
After the device is powered on and started, check whether the device is running properly by observing the status of all indicators on the front panel. For details, see “Basic Function Operations”.
C. Installation of accessories
If the device is not enabled, you need to install the narrowband antenna, power adapter, and LAN cable.
D. Installing the Antenna (Figure 1)
Insert the threaded end of the antenna into the narrow band connector and tighten it.E. Install network cables (Figure 2)
Connect the network cable to WAN network port (Ethernet) for POE power supply (802.3at).F. Install the power adapter (Figure 3)
Plug the cable connector of the power adapter into the 12V power connector of the device.④ Device IP address
Device IP address query method:
Open the iDoorPhone Network Scanner. Press the Refresh button to search the device and find the IP address.
(Download address: http://download.fanvil.com/tool/iDoorPhoneNetworkScanner.exeGateway setting
Step 1: Log in to the device web page
Input IP address (e.g. http://192.168.1.128) into address bar of PC’s web browser.
The default user name and password are both admin.,Step 2: Add the SIP account.
Set SIP server address, port, user name, password and SIP user with assigned SIP account parameters.
Select “Activate”, and then click Apply to save this setting.Step 3: Set up the intercom channel
Set the parameters related to the channel related to the intercom, as shown below. Click “Submit”, and intercom communication requires the same frequency and unique parameters
Type: analog channel or digital channel
Transmit frequency/Receive frequency: The intercom frequency of the call
Power: length of transmitting distance
Recv Sub / Send Sub Tone: analog channel specific parameters
Channel Spacing: analog channel specific parameters
Time Slot: Digital channel specific parameters
Colour Code: Digital channel specific parametersNote: The default transmitting power is low. You are advised to change it to high in normal use.
Step 4: Set intercom parameters
To set the multicast address of the gateway:Set an intercom call number. The intercom transfers the call to the corresponding phone when PTT is pressed. Other parameters are as follows:Step 5: Use of intercom functions:
General mode call:
The IP phone dials the registered sip number of the gateway, and the gateway sets the same channel parameters as the intercom. When the IP phone speaks, the IP phone automatically forwards the call to the intercom. When the IP phone does not speak, the intercom presses the PTT key to automatically forwards the call to the IP phone
Call in PTT mode:
Set the PTT key on the phone to the sip number or multicast address registered on the gateway, set the channel parameters on the gateway to be the same as those on the intercom, set the intercom transfer number on the gateway, press the PTT key to automatically forward the call to the intercom, release the PTT key to end the intercom, and press the PTT key on the intercom to automatically call the number specified in the intercom transfer number. Then release
the PTT key to end the intercom.
Step 6: Application scenario

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Warning Statements:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 24.3cm between the radiator & body.

Responsible Party:
Company name: Oasis Compliance, Inc.
Address:3313 Verdi Dr, San Jose, CA 95111, United States
Tel:2026028330
E-mail:info@oasis-compliance.com
Fanvil Link Technology Co.,LTD
Website: www.fanvil.com
EMail: sales@fanvil.com
support@fanvil.com
Tel: +86-755-2640-2199
Fax: +86-755-2640-2618
Add: 13th Floor, Building 2, Runzhi R&D Center, Xin’an Street, Bao’an District, Shenzhen, Guangdong, China

Documents / Resources

LINKVIL W712 Digital Intercom Gateway [pdf] User Manual 2BCUQ-W712, 2BCUQW712, W712 Digital Intercom Gateway, W712, Digital Intercom Gateway, Intercom Gateway, Gateway

References

• User Manual