Linear Lux V1-KS Rotary LED Dimmer
Vl-KS
Rotary LED Dimmer
- Single channel constant voltage LED Rotary dimmer.
- Match with RF 2.4G single zone or multiple zone dimming remote control optional.
- 0- l 00% dimming smoothly without any flash.A
- logarithmic or linear dimming curve is selectable.
- PWM frequency 500Hz, 2KHz, BKHz or l 6KHz selectable.
- Overheat / Short circuit/ Reverse protection, recover automatically.
- light on/ off fade time 3s selectable.
Technical Parameters
Mechanical Structures and Installations
Wiring Diagram
Wire Preparation:
- The wiring can be solid or stranded with a cross-sectional area of Conventional l mm2 can withstand l OA output current.
- When wiring is installed, the terminals must be tightened.
If they are not tightened, the contact point resistance will be too high 6-8mm and the terminals will easily burn due to heat when used at full load for a long time.
Note: The output power of a constant voltage power supply should be at least 1.2 times that of the output load (light strip), otherwise, the full power output of the load can easily cause automatic flickering or shaking of the light.
PWM frequency setting
We can select four PWM frequencies: 500Hz, 2kHz, SkHz, or l 6kHz. Higher PWM frequency, will cause lower output current, higher power noise, but more suitable for comero(No flickers for video).
Dimming curve setting
Match Remote Control (two match ways)
User can choose the suitable match/delete ways. Two options ore offered for selection:
Use Match key
Match:
Short press match key, immediately press on/off key (single zone remote) or zone key (multiple zone remote) on the remote.
The LED indicator fast flash a few times means match is successful.
Delete:
Press and hold the match key for 5s to delete all match.
The LED indicator flashing fast a few times means all matched remotes were deleted.
Use Power Restart
Match:
Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Switch off the power, then switch on the power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.
Light on/off fade time
When using the RF remote control to turn the lights on and off, you can set a 3s light on/ off fade.
long press match key 5s, then short press match key 3 times, the light on/off time will be set to 3s, the indicator light will blink 3 times. long press match key l Os, restore factory default parameter, the light on/off time also restore to 0.5s.
Malfunctions Analysis & Troubleshooting
Installation Precautions
- The distance between the products should be 2 20cm, so as not to affect the lifespan of the products due to poor heat dissipation.
- The product shall not be installed close to the switching power supply with an interval of 2 20cm to avoid radiation interference of the switching power supply.
- The installation height shall be 2 m from the floor to ovoid shortening the remote control distance due to too weak reception signal.
- The products ore not allowed to be close to or covered by metal objects, with an interval of 2 20cm to ovoid signal attenuation and shorten the remote distance.
- Avoid installation at the corner of the wall or the corner of the beam, with an interval of 2 20cm to ovoid signal interference.
User Manual Ver l .0.0
Documents / Resources
 |
Linear Lux V1-KS Rotary LED Dimmer [pdf] User Guide V1-KS Rotary LED Dimmer, V1-KS, Rotary LED Dimmer, LED Dimmer, Dimmer |
