LIGHTPRO Onyx 12V R1 IP67 Decking Light Installation Guide

Never place your ground spots in holes. Install them on a flat or higher surface.
Provide the hole for the ground spot with a layer of gravel of about 45 cm. This ensures that rainfall can drain away faster, and there is less risk of rising groundwater.

ATTENTION
Take the following steps when removing or replacing the filter:

Ensure that the housing is clean and dry before you turn the ring in the housing. The ring must be able to be tightened properly and sufficiently.
Put the ring straight on top of the body. Make sure at the beginning that the ring is horizontal before turning.
The packaged Onyx has the milk (white) filter built-in.
For questions about parts, service, complaints or other issues you can contact us by sending an email to info@lightpro.info

INTRODUCTION

Thank you for purchasing the Lightpro Onyx.
This document contains the required information for correct, efficient and safe use of the product. Consult the user manual of your transformer for more information about the installation and connection of your lighting plan or visit our website www.lightpro.nl
Read the information in this manual carefully before using the product. Keep this manual near the product for consultation in the future.

PRODUCT DESCRIPTION

The Lightpro Onyx is an LED spot for outdoor use. The fixture can be installed in a fixed underground.
This product may only be used as outdoor lighting in combination with the Lightpro 12-volt system. Any alterations made to the product may have consequences for the safety, guarantee, and correct functioning of the product and/or other parts of the system.

SPECIFICATIONS

Product Lightpro Onyx
Article number
- Onyx 30 RS – 240D
- Onyx 30 RA – 241D
- Onyx 60 RS – 242D
- Onyx 60 RA – 243D
- Onyx 90 RS – 244D
- Onyx 90 RA – 245D
Light source
- Onyx 30 – Led 0,5 W AC/DC 12V
- Onyx 60 – Led 1 W AC/DC 12V
- Onyx 90 – Led 1,5 W AC/DC 12V
Power (max)
- Onyx 30 – Led 0,5 W
- Onyx 60 – Led 1 W
- Onyx 90 – Led 1,5 W
Luminous flux (max)
- Onyx 30 – 4 lm
- Onyx 60 – 23 lm
- Onyx 90 – 60 lm
Light colour 2.700K

Average lifetime 25.000 hours
Dimensions (H x Ø)
- Onyx 30 – 72 x 45 mm
- Onyx 60 – 72 x 75 mm
- Onyx 90 – 78 x 105 mm
Protection class IP67

Ambient temperature -20 °C to 50 °C
Cable length 1m
Dimmable No

Light source is not replaceable
On/off 10.000

PACKAGING CONTENT

[Figure A]

Fixture Onyx 30 / Onyx 60 / Onyx 90
Lightpro connector 137a
Additional lenses

Cable
Ground tube
Check if all parts are present in the packaging. For questions about parts, service, and any complaints or other remarks, you can always contact us.
E-mail: info@lightpro.nl.

INSTALLATION

Option 1: placement in a fixed underground
[Figure B]
1. Install the products in the desired position and lay the cables so that they can be comfortably connected to the transformer or cables.
2. If products are provided with a drain hole for water, this hole must be pointing downwards.
3. Use non-corrosive fixing materials (supplied as standard) if you want to bolt the products down.
4. Connect the lights to the main cable by using the connector as shown on page 5.
5. Plug the plug of the transformer into the wall socket (230 Volt 50 Hz).

Option 2: placement in the ground
[Figure C]
1. Place the ground tube in the ground.
2. Place the fixture in the ground tube.
Proceed as follows if the lamps do not light after you have followed the above instructions:
1. Turn the power off.
2. Check whether all plugs have been connected properly.
3. Check the transformer and the fuse (if applicable, and have them circuit-tested if necessary.
4. Check whether cables have been damaged.
5. Turn the power back on.

REPLACEABLE LENS

[Figure C] Note: The rubber ring must be completely clean before replacing the glass because of the water resistance.

INSTALLATION OF THE LIGHTS

Install the products in the desired position and lay the cables so they can be comfortably connected to the transformer or main cable.

If products are provided with a drain hole for water, this hole must be pointing downwards.
Use non-corrosive fixing materials (supplied as standard) if you want to bolt the products down.
Connect the lights to the main cable by using the connector as shown in the figure on page 5.

Consult the manual of your transformer for more information.

SAFETY

Always fit this product so that it can still be accessed for servicing or maintenance. This product must not be permanently embedded or bricked in.
Turn off the system by pulling the plug of the transformer from the socket for maintenance.

Regularly clean the product with a soft, clean cloth. Avoid abrasives that can damage the surface.
Clean products with stainless steel parts with a stainless steel cleaning agent once per six months.
Do not use a high pressure washer or aggressive chemical cleaning agents when cleaning the product. This can cause irreparable damage.

Protection class III: this product may only be connected to safety extra-low voltage up to a maximum of 12 V.
This product is suitable for outside temperatures of: -20 to 50 °C.
Do not use this product in areas where combustible gases, fumes or liquids may be stored.

NOTE

This product meets the EU standards for health, safety and environmental protection.
For questions about parts, service, any complaints or other matters, you can contact us at any time.

E-mail: info@lightpro.nl
Discarded electrical equipment must not be put in the household waste. If possible, take it to a recycling company. For details of recycling, contact a municipal waste processing company or your dealer.
6 year warranty – visit our website at lightpro.nl for warranty conditions.

FAQ

What should I do if I have questions about parts, service, or complaints?
You can contact us by sending an email to info@lightpro.info for any inquiries or issues.
How should I install the ground spots?
Ground spots should be installed on a flat or raised surface with a layer of gravel about 45cm deep for proper drainage.
How do I replace the filters?
Ensure the housing is clean and dry, then tighten the ring properly and ensure it is straight before turning.

Documents / Resources

LIGHTPRO Onyx 12V R1 IP67 Decking Light [pdf] Installation Guide
30 RS 240D, 30 RA 241D, 60 RS 242D, 60 RA 243D, 90 RS 244D, 90 RA 245D, Onyx 12V R1 IP67 Decking Light, Onyx, 12V R1 IP67 Decking Light, Decking Light

References

User Manual

LIGHTPRO Onyx 12V R1 IP67 Decking Light

Product Specifications

Product Usage Instructions

Installation of ground spots