Leuze electronic DCR 200i-G Camera Based Code Reader
Product Information
Specifications:
- Model: DCR 200i
- Accessories: Housing hoods, diffusor foil
- Screen Options:
- Plastic screen
- Glass screen
- Glass screen with polarization filter
- Tightening Torque: < 25Ncm
Product Usage Instructions
Replacing the Housing Hood:
- Loosen the four fastening screws of the housing hood.
- Tip the housing hood downward and away from the housing.
- Lift the housing hood upward.
Make sure to clean the new hood with a soft cloth before installing. Ensure that the sealing surface in the housing base is clean before installation. Tighten the fastening screws with a torque less than 25Ncm.
Attaching the Diffusor Foil:
- Ensure the surface is free of dust and grease before attaching the diffusor foil.
- Make sure the diffusor foil is correctly oriented (small opening at top, large opening at bottom).
- Attach the foil to the housing screen from bottom to top, preventing bubbles from forming under the film.
Order Guide:
| Designation | Part No. |
|---|---|
| Housing hood with Plastic screen | Cover DCR 200i – 50131462 |
| Housing hood with Glass screen | Cover DCR 200i-G – 50131461 |
| Housing hood with Glass screen and Polarization filter | Cover DCR 200i-P – 50131460 |
| Diffusor foil for the screen of the Diffusor DCR 200i | 50131459 |
Contact Information:
- In der Braike 1 D-73277 Owen
- Tel. +49 (0) 7021 573-0
FAQ (Frequently Asked Questions):
- Q: Can I use the diffusor foil with the polarization filter?
A: The diffusor foil (50131459) is not suitable for use in combination with the polarization filter.
- Housing hoods to be used as a replacement in the event of changed operating conditions or as a replacement for defective or scratched original hood.
- Housing hoods with either plastic or glass screen (optionally with polarization filter)
- Diffusor foil for increased scatter of the integrated LED illumination of the code reader.
Remarks
Operate in accordance with intended use!
The product may only be put into operation by competent persons.
Only use the product in accordance with the intended use.
Order Guide
| Housing hood with | Designation | Part no. |
| Plastic screen | Cover DCR 200i | 50131462 |
| Glass screen | Cover DCR 200i-G | 50131461 |
| Glass screen and polarization filter | Cover DCR 200i-P | 50131460 |
| Diffusor foil For the screen of the housing hood |
Diffusor DCR 200i | 50131459 |
Accessories – housing hoods, diffusor foil
Replacing the housing hood
Cover DCR 200i…
Only replace the housing hood while there is no voltage in the system!- Clean the new hood with a soft cloth before installing.
- Make certain that the sealing surface in the housing base is clean before installing!
- Tightening torque of the fastening screws < 25Ncm!
- Loosen the four fastening screws of the housing hood.
- First, tip the housing hood downward and away from the housing. Next, lift the housing hood upward.
- Then mount the new housing hood in the reverse order (3 2, 1).
Attaching the diffusor foil
Diffusor DCR 200i…
- The diffusor foil (50131459) is not suitable for use in combination with the polarization filter!
- Before attaching the foil, make certain that the surface is free of dust and grease!
- When attaching the diffusor foil, take care to prevent bubbles from forming under the film!
- Make certain that the diffusor foil is correctly oriented (small opening at top, large opening at bottom).
- Attach the foil to the housing screen from bottom to top.
- Leuze electronic GmbH + Co. KG
- Email: info@leuze.com
- Website: www.leuze.com
- In der Braike 1 D-73277 Owen
- Tel. +49 (0) 7021 573-0
Documents / Resources
 |
Leuze electronic DCR 200i-G Camera Based Code Reader [pdf] Owner's Manual 50131461, 50131462, 50131460, 50131459, DCR 200i-G Camera Based Code Reader, DCR 200i-G, Camera Based Code Reader, Based Code Reader, Code Reader, Reader |
