LeTianPai AAD2C Desktop Robot
USER MANUAL
Product description
Robot Standing Position for Wireless Charging
The normal wireless charging station position of the robot. with the robot screen as the front, align the center of the robot’s right foot with the wireless charging logo •dot• on the charging board.
Connect the robot to a Wi·Fi network
1. Charging the robot with the data cable.
2. Choose Wi-Fi and enter the password on the robot’s screen to connect to the network.
3. Open the Letianpai APP, bind with the pairing code displayed on the robot.
4. For more information, please check the detailed usage guide in “Control – Manual” or https://global.letianpai.com/all/sms/robotl
Note:
1. The foot of the cobot is equipped with a 60 ° physical cacd position. Please do not manually cotate excessively, cesulting in man-made damage;
2. Do not manually quickly cotate the mbot’s legs, feet, and antenna to avoid damage to components,
3. Do not place the cobot neac the soucce of fice 01 watec;
4. Please avoid the cobot being squeezed, dcopped, and violently collided,
5. Replace the charger if the charging current is less than 5V-0.5A.
Foe detailed instcuctions and explanations, please check the electconic manual.
Warranty
Letianpai gcarantees that warranty service will be provided for this prodcct starting from the date of pcrchase. The prodcct’s warranty period depends on the specific component type. The warranty period varies and can be cp to 12 months (or longer where reqcired by local law) for different components. For more information aboct the warranty period and after-sales service policy,
Please visit https://global.letianpai.com/all/service/robot
Warranty policies may vary according to local laws and regclations.
Servlce Tel: + 86 400-053-3086
Servlce webslte: www.Let,anpa,.com
Brand owner: Shenzhen Letlanpal lnnovatlon Technology Co., Ltd
Manufacturer: Beljlng Renhejla Technology Co., Ltd
Address: Room 403, 4th Floor, Bulldlng 1, Yard 19, Belyuan East Road, Chaoyang Dlstrlct, Beljlng
| Warranty card | |
| Product infomation | |
| Product name | |
| Product model | |
| Product SN No | |
| Date of ourchase | |
| User information | |
| User name | |
| Contact number | |
| Addcess |
The pmd,ct type appm,al code CMIIT ID ls displayed o, the f,selage aameplate。
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radionv technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RF Exposure Statement
To maintain compliance with FCC’S RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm between the radiator and your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
Specifications:
- Product Name: Robot AAD2C
- Product Model Number: Q/RHJ 001-2023
- Protection standards: GB/T 26572
- Approval Code: CMIIT ID
FAQ:
Q: How do I charge the robot?
A: To charge the robot, use the provided charging cable and connect it to a power source as directed in the manual.
Q: How do I clean the robot?
A: Use a soft, dry cloth to gently wipe the exterior of the robot. Avoid using water or cleaning solutions.
Documents / Resources
 |
LeTianPai AAD2C Desktop Robot [pdf] User Manual 2BKID-AAD2C, 2BKIDAAD2C, AAD2C Desktop Robot, AAD2C, Desktop Robot, Robot |
