
LED Motion Security Light
User Manua’
READ ALL WARNINGS AND INSTRUCTIONS BEFORE INSTALLING THIS
PRODUCT TO ENSURE SAFETY AND PROPER OPERATION, KEEP THIS
MANUAL GUIDE FOR FUTURE REFERENCE
WARNING
- Failure to install and wire fixture in accordance with the National Electrical Codes (NEC), all applicable Federal, State, and Local electrical codes, as well as specific U.L. safety standards for the intended working environment (location/application), may cause serious personal injury, death and/or property damage.
- Risk of fire or electric shock, installation of the device requires knowledge of the luminaries’ electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- Do not alter, relocate or remove the wiring, lamp holder, power supply or any other electrical components.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- Do not operate the device if there’s any visible damage to the device.
- Do not operate the device if there are any signs of smoke, steam, over-heating or crackling noise that can be heard from the device.
- The manufacturer will not be deemed liable or held responsible for any damage caused by faults or manufacturing defects that may be present in any of its products or the misuse or incorrect installation of the device.
- TURN OFF POWER FROM THE MAIN CIRCUIT BEFORE INSTALLING THE FIXTURE. Make sure the fixture is grounded per National Electrical Codes (NEC).
INSTALLATION
- Tools needed: Philip’s and Flathead screwdrivers, adjustable wrench, wire nuts, electrical tape, and silicone caulk.
- Exercise caution and care when handling fixtures to avoid cuts and abrasions, it is recommended to use rubber sole shoes to avoid the chance of electric shocks.
- Carefully unpack and check the contents of the box to be sure everything is included.
- Turn OFF the power at the circuit breaker box.
- Install Cross Bar (10) to the junction box using two 3/4″ screws (11).
- Electrical Connections: Make sure the supply and ground wires go through the Gasket (15). Attach the green or bare copper wire and the green ground wire of the fixture (6) to the crossbar (10) using the groundnut. (Ground wire must be properly attached or unit may not work). Connect the white supply wire to the white fixture wire (8), then cover them with a wire nut (7) or twist together and cover really well with electrical tape. Repeat this with the black supply and black fixture wires (9). Push the connected wires back into the electrical box.
- Install Bracket Screw (1) into the center hole of Fixture Back Mount base (5). Align Fixture over J-box with the Gasket (15) between it and the Canopy. Secure the unit to the Cross Bar by tightening Center Bracket Screw. Loosen the adjustment knobs (13) and aim the lamp heads (14).
- Turn on electricity at fuse or circuit breaker box and Test Unit success of the installation. (see the motion)
- Place a small streak of silicone caulk on the edge of the fixture bracket, except at the lower edge. Place the bracket of the fixture so the bracket connecting screw protrudes out of the hole in the fixture bracket. Make sure the fixture is set right side up on the mounting surface. Check that the caulking sealant is completely around the edge of the bracket where it meets the wall’s surface (there should not be caulking at the lower edge). Use the securing nut with a rubber washer (3) to tighten up the bracket to the wall. Adjust the two nuts in the bracket connecting screw if the fixture bracket is not tight against the wall. Make sure the unit is tight and secure.

MOUNTING BRACKET

WIRING THE LIGHT FIXTURE

MOUNTING THE LIGHT FIXTURE

CAULKING AROUND THE LIGHT FIXTURE

OPERATION GUIDE
3 Knobs:
By turning the 3 knobs on the right side, 3 kinds of settings can be adjusted as follows:
Lux Knob: The sensitivity of the Photosensor is changeable
, turn the first knob clockwise, the light intensity will rise and vice versa.
Time Knob: Lasting time of the lighting is changeable (5secs – 5mins), turning the second knob clockwise raises the delay time and vice versa.
Range: The max distance of the motion sensor is changeable (6.56 – 22.97yds.), turn the third knob clockwise and the detection distance will increase and vice versa.
3 Modes: 3 lighting modes are available by slipping the arrow of the 3-way switch on the left side.
ON-TIME Mode – The light would be on after you switch it on like normal light bulbs.
AUTO Mode – Turn the Lux knob counterclockwise until max. This light will stay off during the day and will turn on at night when motion is detected. After acertain amount of time set by you, the light will turn off when no motion is detected.
Please note that by turning the Lux Knob clockwise, the sensor will detect motion. earlier in the day. At the max setting, it will turn on when motion is detected, even during the day.
Dusk-to-Dawn Mode – Turn the three knobs counterclockwise until the lowest setting and then slip the switch to D2D mode, this puts the light into dusk-to-dawn mode. At night, the light will turn itself on during this mode and then off during the day.
Please note that turning the Lux knob clockwise will lower the photocell sensitivity and if it goes past max, the light will stay on no matter what time of day it is.

WARRANTY
LeonLite warrants that this product is free from defects in materials and workmanship for a period of 5 years from the day of purchase. This warranty does not apply if the product has been damaged through misuse, abuse, accident, modifications, alterations, neglect or mishandling.
Documents / Resources
![]() | LED Motion Security Light |
References
- User Manualmanual.tools

I have the 3 light 300 warm leonlite lights around my home. With one of the lights there seems to be a bulb malfunction. It is coming on but instead of going completely off as the other 2, there is a very small amount of white light still emitting from the one bulb and will not go out when the others are at rest (off).
Why is one of my LeonLite LED motion security lights emitting a faint glow instead of turning off completely?
The issue you are describing, where an LED remains faintly lit even when the switch is 'off', is often referred to as 'ghosting.' This is typically caused by a small amount of residual current leaking through the circuit, which is enough to power high-efficiency LEDs but not traditional bulbs.
Based on the LeonLite manual and common LED troubleshooting, please check the following:
If the wiring is confirmed correct by a professional and the issue persists, LeonLite offers a 5-year warranty as noted in the manual. You may need to contact their support for a replacement unit if the internal circuitry is defective.
Read the full Q&A page
I have already just sent the first email! I wanted to include my date of purchase info. Curtis Cuevas, Amazon ORDER # 112-6202453-6637041. Bought 4 on 02/23/2019. Bronze, 3-head, motion. 5 year warranty. I can return the defective one if you need! In the first email from me you can get all the description of the issue I am having. One of the 3 bulbs is not going all the way out along with the others. A small white light remains when sensor time goes off. This may help collate the two emails together. Thanks!
One of the three LED heads remains partially lit with a small white light after the sensor timer expires. How can I resolve this, and do I need to return the defective unit under the 5-year warranty?
Based on the LeonLite LED Motion Security Light manual, here is the information regarding your issue and warranty:
We recommend following up on your email to LeonLite customer support with the specific Amazon order details you provided here.
Read the full Q&A page
I’ve purchased 2 LeonLite 20 w dual he’d motion activated floodlights.
Neither shut off at night when no motiondetected. It is set to Auto. Lux turned all the way counterclockwise.
Neither shut off at night when no motiondetected. It is set to Auto. Lux turned all the way counterclockwise.
Why do my LeonLite LED motion security lights stay on at night even when no motion is detected?
If your LeonLite LED Motion Security Light is staying on at night without motion, please check the following settings based on the manual's operation guide:
Read the full Q&A page
I have a 20W Dual Head Motion Activated Floodlight. It is under two years old and the motion sensor is malfunctioning. Sometimes the lite comes on if you stand under it and wave, and most of the time it will not lite at all. I live in Arizona and wander if the sun has damaged or blurred the lens till it won’t respond?Can I get a new sensor for the lite under warrantee?
How can I troubleshoot a malfunctioning motion sensor on my LeonLite 20W Dual Head Floodlight, and is it covered under warranty?
Based on the LeonLite LED Motion Security Light manual, here are the steps to address your sensor issues and warranty inquiry:
LeonLite typically does not provide individual replacement sensors; instead, they usually replace the entire unit. You should contact LeonLite customer support with your proof of purchase to initiate a warranty claim.
Read the full Q&A page
I just had the leonlite installed 9n my back deck. Light comes on with the light switch. 20 seconds later the light starts flashing. Help
Why is my LeonLite LED Motion Security Light flashing 20 seconds after being turned on?
Flashing or flickering in motion security lights often indicates a conflict between the sensor settings and the ambient light levels, or a wiring issue. Based on the LeonLite manual, please check the following:
If the flashing persists regardless of knob adjustments, there may be a defect in the sensor or a compatibility issue with the power source (such as being connected to a dimmer switch, which is not supported).
Read the full Q&A page
I bought a four pack of LeonLite 12v LED low voltage lighting. Amazon order 112-3193941-9401848. Three of the four lights no longer work.
It states a five year warranty. When can I expect to receive replacements?
It states a five year warranty. When can I expect to receive replacements?
How can I claim the 5-year warranty for my LeonLite 12v LED low voltage lights that have stopped working?
According to the LeonLite manual, the product is covered by a 5-year warranty from the day of purchase against defects in materials and workmanship. This warranty does not cover damage resulting from misuse, abuse, accident, modifications, alterations, neglect, or mishandling.
To initiate a warranty claim and receive replacements, you should contact LeonLite customer support directly. While the manual confirms the warranty period, it does not list a specific phone number or email. You can typically reach LeonLite through the following channels:
When contacting them, be sure to provide your Amazon Order ID (112-3193941-9401848) and a description of the failure to expedite the replacement process.
Read the full Q&A page
How do you put in light bulbs in 20w dual sensor motion activated floodlight?
How do you install light bulbs in the LeonLite 20W dual sensor motion activated floodlight?
Based on the LeonLite LED Motion Security Light User Manual, this fixture features integrated LED technology. This means the light source is built directly into the lamp heads and does not use traditional replaceable light bulbs.
If the light is not functioning, please check the following:
If the integrated LEDs have failed, the entire fixture typically needs to be replaced, as the manual does not provide instructions for bulb replacement. LeonLite offers a 5-year warranty for defects in materials and workmanship; you may wish to contact their support if the unit is within the warranty period.
Read the full Q&A page