legrand Y4652M2 Basic Control BUS 2 Modules
Description
Two-module flush mounted control, capable of handling functions up to: 4 ON/ OFF lights and dimmer, 2 shutter up/down and advanced features such as 4 scenario activations and VDE floor call functions, staircase light switch-on and lock activation.
To be completed with 1 or 2-module covers.
In case of management of groups of lights, this device support the return state (please check the production date starting from 26W17).
Front view
Technical data
| Power supply from SCS BUS: | 18 – 27 Vdc |
| Absorption: | 6 mA (stand-by) 7 mA (max) |
| Operating temperature: | 0 – 40 °C |
Front view without protective shell
Dimensional data
| A | B | C | D |
| 45 mm | 45 mm | 16.7 mm | 6.9 mm |
Legend
- Protective shell
- Status notification LED
Y4652M2:
Blue steady = load ON
White steady = load OFF
Blue flashing = object not configured
MX5222/MX5222C:
Purple steady = load ON
Blue steady = load OFF
Purple flashing = object not configured - Control pushbutton
- LED pushbutton (*)
Rear view
Legend
- BUS clamp
- Safety and sealing clear cap
Caution: do not delete - Configurator socket:
A1 = area 1
PL1 = light point 1
M1 = mode 1
A2 = area 2
PL2 = light point 2
M2 = mode 2
List of functions
The device create the following functions:
- Light control
- Automation control
- Plus programmed scenario activation
- Video door entry controls
- Commands only available with virtual configuration
Configuration
For device configuration and installation and for any other information, refer to the App or documentation that can be downloaded from the on-line catalogue of the device.
|
Download App |
|
|
Home + Control |
Home + Project |
The apps can be downloaded from their respective stores.
It is recommended to update the smartphone or tablet operating systems to the latest available version.
In addition, PHYSICAL CONFIGURATION will continue to be guaranteed by inserting the configurators in the appropriate housings (*).
The configuration using Home + Project has the advantage of offering many more options when compared with the physical configuration.
For the list of modes and the corresponding meanings refer to the indications of this technical sheet and the Home + Project app.
(*) Physical configuration
Light control
Addressing
| Address type | Configurators | |
| Point-to-point | Room | A1, A2=1-9 |
| Light point | PL1, PL2=1-9 | |
| Room | A1, A2=AMB, PL1, PL2=1-9 | |
| Group | A1, A2=GR, PL1, PL2=1-9 | |
| General | A1, A2=GEN, PL1, PL2=0 | |
Mode
ON/OFF control
Here is the data extracted from the image:
| Function | Parameter / setting | Configurators | |||
| Cyclical | M1, M2=0 | ||||
| ON | M1, M2=ON | ||||
| OFF | M1, M2=OFF | ||||
| Pushbutton | M1, M2=PUL | ||||
| Timed ON* | 0,5 sec | M=8 | |||
| 30 sec | M=7 | ||||
| 1 min | M=1 | ||||
| 2 min | M=2 | ||||
ON/OFF control and ADJUSTMENT (Point-to-Point only):
| Function | Configurators |
|
Cyclical ON/OFF and ADJUSTMENT. |
M1, M2=0 |
| ON with upper button, OFF with lower button and DIMMER when held down | M1, M2=0/I |
Automation control
Addressing
| Address type | Configurators | |
| Point-to-point | Room | A1, A2=1-9 |
| Light point | PL1, PL2=1-9 | |
| Room | A1, A2=AMB, PL1, PL2=1-9 | |
| Group | A1, A2=GR, PL1, PL2=1-9 | |
| General | A1, A2=GEN, PL1, PL2=0 | |
Mode
| Function | Configurators |
| Bistable control | M1, M2=↑↓ |
| Monostable control | M1, M2= ↑↓ M |
| Monostable when pressing briefly and bistable when holding down | M1, M2=6 |
Video door entry functions
Door lock release control
Addressing
| Addressing type | Configurators |
| Entrance panel address | A=1-9 PL=1-9 1) |
Note 1): Set the P address (two digits) of the entrance panel from which to control the door lock using the bottom left module.
The bottom right module controls the door lock of entrance panel P+1 se A2=PL2=M2=0.
Type of function
| Function | Configurators |
| Door lock release control | M1, M2=3 |
Floor call control
Addressing
Define the address (two digits) of the internal unit to be called using the control device.
| Addressing type | Configurators |
| Internal unit address | A=1-9 PL=1-9 |
| General | A=GEN A/PL=0 |
Type of function:
| Function | Configurators |
| Floor call control | M=4 |
Staircase lights control
Addressing
The device takes on the function of push button for switching on the lights of the internal unit identified by its own address (two digits).
| Addressing type | Configurators |
| Internal unit address | A=1-9 PL=1-9 |
Type of function:
| Function | Configurators |
| Staircase lights control | M=5 |
Customer Support
Documents / Resources
 | Y4652M2 Basic Control BUS 2 Modules |
References
- legrand.comwww.bticino.comwww.legrand.comwww.bticino.com
- User Manualmanual.tools