SmallRig SR-RG2 Wireless Remote Controller
In the Box
- Remote Controller
- Operating Instruction
Product Details
- Battery level and Charging Indicator
- BLE Indicator
- TW: Zoom Button
- REC Button
- Custom button
- Focus/ Shutter Button
- ON/OFF Button
- USB·C Charging Port
- Focus/Shutter Button:
- Half-press for focusing. Fully press for taking a photo.
- Customizable “C” Button:
- Nikon Camera: Corresponds to the function set in Fn 1 custom settings.
- Sony Camera: Corresponds to the function set in Cl custom settings.
Specifications
- Operating Voltage 3.7V
- Operating Current SmA
- Battery Parameter 3. 7V / 200mAh / 0. 7 4Wh
- Control Range Approximately 1 Om
- Operating Temperature -4o·c
- Product Dimensions 174.8 x 46 x 39.4mm / 6.9 x 1.8 x 1.6 in
Indicator light description
If there is no button press or change in Bluetooth status wi t1in l 0 seconds. Both indicator lights will turn off. To check the current battery level or Bluetooth status during this period, press any key.
BLE Indicator Light
- Slow flashing blue light: BLE connection failure/disconnected
- Rapid flashing blue light: BLE connection in progress
- Steady blue light: BLE connection successful
Battery Indicator Light
- During Shutdown Charging:
- Slow flashing blue light: Charging in progress
- Steady blue light: Charging completed
During Power On and in Use:
- Steady blue light: Battery> 20%; Steady red light: l 0% < Battery s 20%; Red light flashing: Battery:sl 0%.
Firmware Upgrade Status:
- Battery lindicatorrLight – Steady red and BLE Indicator Light – Steady blue
Pairing Steps
| Brand | Sony |
|
InitialPairing Steps |
©Switchthe remoteee controller page, switch to [ON], and theblue indicatorr light will flash slowly. @Adjust Camera Settings: a. Select [MENU] – [BLEsettings] – [Enable] b. Select [MENU] – [BLEconnection] – [Connect to Wireless Remote] – [Adda device to connect to]. @Press and holdd the remote controller’s [Customizable ·c·Button+ Rec Button] until the BLEindicator light on the remote controller char. ges from fast flashing tosteady light thenrelease. @The camera screen indicates [Pairedwah: SR·RG2], select [OK] to complete the pairing. @The remote controller can now controll the camera. |
|
Reconnection Pairing Steps |
Once the remote controller and the camera have completed the initial pairing, reconnecting to tile cameraa is as simple as as pressing any key onn the remote controllerr:
1. Set the remote controller power switch to [ON), and the Bluetooth indicator light will flash slowly. 2. Press any key on the remote controllerr. The theBLEindicator light ontheremotecontroller will change from fast flashing to steady light, indicating a successful pairing. *Exceptions: 1. you have connected the remote controller to another camera after the initial pairing. Please follow the initial pairing steps. 2. If you havee intentionally removedthis remotecontroller from the camera after the initial connection. please follow the initial pairing steps. |
|
1. Confirming the setting on the camera: |
|
| Q&A: | select [MENU] – [Network!- !Transfer/ Remote] – [BLE Rmt Ctrl] |
| Unable to Use Property After
Successful Pairing |
andmake sure that [ONJ is selected.
2. Restart the remotecontroller and the camera’s [BLEsetti s], andstart the pairing process from Initial Pairing Steps. |
The method of setting up remote shooting may vary depending on the camera model. For detai led information, please refer to the relevant chapter on remote controllers in the camera user manual.
| Brand | Nikon |
|
Initial Pairing Steps |
© Switch theremote controller power switchto ION], and
theBLEindicator light will flashslowly. @MJUSt Camera Settings: a Selea [MENU) – [NETWORK MENU) -[Bluetooth remote cntrl options) – [Savewireless remotecontroller] ®Press and hold theremotecontrollefs [Customizable ‘C”Button+ RecBt.tton] until theBLE indicator light ontheremotecontrollercharges from fast flashingtosteady light thenrelease.@Thecanerascreenindicates [Wireless remotecontroller saved], sele<:t [OK] to complete the pain . ®Theremotecontroller cannow cortrol thecamera. |
|
Reconnection Pairing Steps |
Once theremotecontroller and the camera havecompleted tne initial pairing, reconnecting to the camerais assimple as pressing any key on the remote controller:
1. Set the remote controller power switch to [ON). and the BLE indicator light will flash slowly. 2. Press any key on the remote controller.The BLE indicator light on the remotecontrollerwillchange from fast flashingto steady light, indicating successful pairing. *Exceptions: 1. If youhaveconnected the remote controller to another camera after the initial pairi11g, please follow the initial pairi steps. 2. If youhave intentionally removed this remotecontroller from thecameraafter theinitialconnection. please follow the initial pairing steps. |
|
1. Confinningthe settingon thecamera: |
|
| Q&A:
Unable to Use Property After |
Selea [MENUJ – [NETWORK MENU) -[Bluetooth remotecntrl options]
-Select [Bluetoothremotecrirlconnectiorl -[ON]. 2. Restart theremotecontrollerandthe cameras |
| Successful Pairing | [Bluetooth remotecntrl options),and start thepairing
process fromInitial PairingSteps. |
The method of setting up remote shootin g may vary depending on the camera model. For detailed information, please refer to the relevant chapter on remote controllers in the camera user manual.
| Brand | Canon |
|
Initial Pairing Steps |
(j) Switch the remotecontroller power switch to [ON], and the BLEindicator light will flash slowly.
@Adjust Camera Settings: a. Select [MENU] – [BLE settings] – [Enable] b. Select [MENU] – [Connect to Wireless Remote] – [Adda deviceto connect to] c. Thecamera screen indicates [Pairinginprogress. Start pairing on the WirelessRemote] ® Press andholdtheremotecontroller’s [Customizable·c·Button+ Rec Button[ until theBLEindicator lighton the remote controller changes from fast flashingto steady light, thenrelease. @The camera screen indicates [Pairedwith: SR·RG2], select [OK] to complete thepairing. ® Still Mode: Select [MENU] – [Drivemode] – [Self·timer:10 sec], [Sel timer: 2 sec], (Single Shooting], andetc.- [SET:OK], then controller can control the camera. @Video Mode: Adjust the camera dial to (Video Mode], and the remote controller can control the camera. |
|
Reconnection Pairing Steps |
Once theremotecontrollerand thecamera have oompletedthe initial pairing re-connectingto thecamerais as simple aspressingooy key
ontheremotecontroller: 1. Set theremotecontroller power swochto[ON], llldtheBLE indicator light will flash slowly. 2. Press any keyon theremotecortroller. TheBLE indicatorligtt on theremotecontroller will change from fast flashing to steady light, indicating s1.ttessfupairing. “Exceptions: If theremotecontrollerhas been pairedwithanother camera after the initial pairing,please [Delete connectioninformation: OeleteSR G2J first, llldthenfollowtheinoial painrg stepsagain. Ifyouhaveintentionallyremoved thisremote oontrollerfrom the camera after theinitialconnection.pleaserepeat theinitial pairingsteps. |
|
Q&A: Unable to Use Properly After Successful Pairing |
1. Confinningthe setting on the camera:
Check[MENU] – [Network settings] – [BLEsettings] llld makesurethat [Enable]isselected. 2. Still Mode:Please makesure[MENU] – [Drive mode] – [Selftimer.10 sec], [Sel timer.2 sec], [Single Shooting – [SET: OK] is selected. 3. Restan theremotecontrollerandthe camera’s [BLE settings], and start thepairingprocess from Initial PairiogSteps. |
*The method of setting up remote snooting may vary depending on the,camera model.For deta iled information, please refer to the relevant chapter on remote controllers in the camera user manual.
SmallRig Up APP
APP Download Instructions:
You can download the “SmallRig Up’ app from the application store or Apple Store.
APP Purpose:
The latest firmware for the remote controller can be downloaded and updated through the SmallRig Up app.
Note:
- Please ensure that the remote contro ller’s battery indicator light is blue and that your phone has sufficient battery before proceeding with the update.
- During the update process, do not press any buttons or switches on the remote controller.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- To assure continued compliance, any changes or modifications not expressly approved by the party.
Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
RF warning statement:
- The device has been evaluated to meet general RF exposure requirement.
- The device can be used in portable exposure condition without restriction.
- Rooms 101, 701, 901, Building 4, Gonglianfuji Innovation Park, No. 58, Ping’an Road, Dafu Community, Guanlan Street, Longhua District, Shenzhen
Documents / Resources
 |
SmallRig SR-RG2 Wireless Remote Controller [pdf] Instruction Manual 2BC2U-SRRG2, 2BC2USRRG2, srrg2, SR-RG2 Wireless Remote Controller, SR-RG2, Wireless Remote Controller, Remote Controller, Controller |
