“
Specifications
- Wheel Type: Neo X Formula Steering Wheel/GT
- Materials: Carbon Fiber Composite Material
- Programmable RGB Buttons: 8
- 7-way Multi-position Rotary Switch
- 12-Set Programmable LED Encoders
- Thumb Rotary Encoders: 2
- UP+ Shifter modules: 2 Seperate Purchase Required
- Button Cap Stickers included
- Dimensions (Length x Width x Height): 189.6 x 109.1 x
153.7mm - Net Weight: 1075g (With Quick Release, No Paddles)
- Quick Release Accessories: SIMAGIC QR50 Included
- Optional Accessories: Installation Kit, Connecting line, Button
Cap Stickers, Maglink, Wheel Rim, QR70 Quick Release
Product Usage Instructions
Before Setting Up
Thank you for purchasing the SIMAGIC Neo X Hub! Before setting
up the hub, carefully read all the documentation that came with the
package. The Hub is intended for indoor use only and recommended
for ages 15 and above.
Quick Guide
Steering Wheel Function Shortcuts:
- Clutch Calibration Mode: Push both 7-way
switches upward for 5 seconds to enter clutch calibration mode.
Press each clutch paddle fully once to complete calibration. Note:
The paddle module with clutch paddles must be installed. - Factory Reset: Press and hold for 5 seconds to
restore factory settings (for the steering wheel only).
Installation Instructions
Paddle Shifter Module Installation:
- Remove the two screws
- Take off the paddle cover
- Connect the wire to the terminal socket
- Position the paddle module
- Tighten the two screws
Steering Wheel Grips Installation:
- Position the grips
- Place the decorative cover
- Tighten the 6 screws
Connecting Instructions
Wheelbase Connection:
- To connect to the base, insert the steering wheel into the base
and press the pairing button to initiate connection. - Hold for more than 5 seconds to enter automatic pairing
mode. - If pairing is unresponsive, use the included USB Type-C cable
to connect the USB ports on the back of the steering wheel and the
base for manual pairing. Please disconnect the cable after pairing
is successful.
Connecting the Steering Wheel to a PC:
Use the included USB Type-C cable to connect the steering wheel
to the PC.
Frequently Asked Questions (FAQ)
Q: Can I use the Neo X Hub for outdoor activities?
A: No, the Neo X Hub is intended for indoor use only.
Q: How do I restore factory settings for the steering
wheel?
A: Press and hold for 5 seconds to restore factory settings for
the steering wheel only.
“`
USER MANUAL
Contents
1. About SIMAGIC 2. Introduction
2.1 Overview 2.2 Specifications 2.3 Package Contents 3. Instruction of Use 3.1 Quick Guide 3.2 Software__Simpro Mananger 4. Warranty Description 5. Safety 6. Contact us
Neo X
03 04 04 05 06 07 11 12 13 15 16
USER MANUAL
Thank you for choosing
Neo X
Before using your new Neo X, please review this manual for essential information about your health and safe usage of the product. KEEP RACING!
USER MANUAL 03
2. NeoX Introduction
2.1 Overview
Neo X
Neo X Hub
· High-Strength Carbon Fiber Composite with High-Tech Fragmented Surface · Personalized Driving Experience:
· 8 customizable RGB buttons · 2 thumb knob encoders · 2 seven-way switches · 2 12-Set Programmable LED Encoders · 9 soft light programmable RGB rev light · Quick-response button layout for efficient interaction · Modular Shift Paddle Options: · Multiple configurations with adjustable shapes, materials, and widths · Easy Compatibility and Customization: · UP+ upgrade modules for quick and flexible wheel swaps · Neo X compatible with 6×70 mm bolt patterns, fitting most racing wheels · New quick-release adapter compatible with 50 mm and 70 mm quick releases · Ergonomic Design with Simpro Manager Support
USER MANUAL 04
2.2 Specifications
Neo X
SpPerocdiufcitcNaatmioens
Wheel Type
Materials
Programmable RGB Buttons
7-way Multi- position Rotary Switch 12-Set Programmable LED Encoders Thumb Rotary Encoders
UP+ Shifter modules
Button Cap Stickers
Dimensions (Length x Width x Height)
DeNteat Wileeidghdt ata
Neo X Formula Steering Wheel/GT Carbon Fiber Composite Material 8 2
2
2 Seperate Purchase Required included 189.6 x109.1 x153.7mm
1075g (With Quick Release, No Paddles)
Quick Release Accessories Optional Accessories
SIMAGIC QR50 Included
Installation Kit Connecting line, Button Cap Stickers
Maglink, Seperate Purchase Required, Wheel Rim, QR70 Quick Release
* Specifications subject to change without notice
USER MANUAL 05
2.3 Package Contents
· USB Type-C x 1 · Countersunk Head Screw M5-16 x 6 · Cap Stickers x 1 · Allen Key x 22mm/3mm)
Neo X
The accessorie above are optional and not included in the package
USER MANUAL 06
3. Instruction for Use
Neo X
Thank you for purchasing the SIMAGIC Neo X Hub!
Before setting up the hub,carefully read all the documentation that came with the package.
· For information about firmware upgrades, please check www.simagic.com/download. * The related files are game adaptation files developed by SIMAGIC for SIMAGIC-compatible devices. To safeguard users’ legal rights and interests, please download all files through SIMAGIC’s designated channels.
· Please visit Simagic official YouTube channel (https://www.youtube.com/@simagicofficial6890) for tutorial videos showcasing different setup options and usage techniques.
· Please visit www.simagic.com/telemetry-support to access the list of games supported by this product. Note that using this product in nonsupported games may result in certain functions not working as intended.
The Hub is intended for indoor use only 15+ Recommended ages 15 and above
USER MANUAL 07
Neo X
3.1 Quick Guide
Steering Wheel Function Shortcuts
Clutch Calibration Mode
Factory Reset
Push both 7-way switches upward for 5 seconds to enter clutch calibration mode. Press each clutch paddle fully once to complete calibration. Note: The paddle module with clutch paddles must be installed.
Press and hold for 5 seconds to restore factory settings (for the steering wheel only).
Steering Wheel Adjustment
Paddle Shifter Module Installation
Remove the two screws Take off the paddle cover
Connect the wire to the terminal socket Position the paddle module Tighten the two screws
USER MANUAL 08
Steering Wheel Adjustment
Steering Wheel Grips Installation
Neo X
Position the grips Place the decorative cover Tighten the 6 screws
Connecting the Steering Wheel to the Base
The quick-release structure of the steering wheel has six steel balls on the top and four on the bottom.
6 steel balls
4 steel balls
Line up with the wheelbase.
USER MANUAL 09
Wheelbase Connection
Neo X
To connect to the base, insert the steering wheel into the base and press the pairing button to initiate connection.
Hold for more than 5 seconds to enter automatic pairing mode.
If pairing is unresponsive, use the included USB Type-C cable to connect the USB ports on the back of the steering wheel and the base for manual pairing. Please disconnect the cable after pairing is successful.
USER MANUAL 10
Connecting the Steering Wheel to a PC
Neo X
Use the included USB Type-C cable to connect the steering wheel to the PC.
USER MANUAL 11
Neo X
4. Software
Simpro Manager will automatically notify you if there are available updates for the software. If you want to double-check, please go to www.simagic.com/download and download the newest version. Simpro Manager has a built-in feature that allows you to update the firmware on your devices automatically.
Scan QR Code
USER MANUAL 12
Neo X
5. Warranty Description
Warranty Terms
The warranty period is12 months from the date of purchase. During the warranty period, if there are issues with the machine’s components, materials, or craftsmanship under normal use and maintenance, and the problem is confirmed after inspection, the company will provide free repairs and replacement parts.
SIMAGIC product’s Serial Number (S/N) will serve as the primary identifier for after-sales support. You can locate the S/N on the product packaging and the product itself, attached via a sticker on the product surface. Simply provide the 10 or 14-digit S/N to our customer service team or SIMAGIC distributor when applying for after-sales service, and they will assist you promptly.
For users who have products with serial numbers, there’s no need for warranty cards. However, if your product does not have a serial number, you will need to retain your warranty card for after-sales support.
S/N
Your product’s serial number can be found on the label sticker of wrapping
* Consumer Law. This Limited Warranty gives you specific legal rights, and you may have other
rights that vary by your country, province or state, as applicable. Other than as permitted by law, Simagic does not exclude, limit or suspend other rights you may have. For a full understanding of your rights, you should consult the laws of your country, province or state, as applicable.
USER MANUAL 13
Neo X
5. Warranty Description
Warranty Terms
SIMAGIC establishes dealer terms and consumer product warranty terms, requiring official partners such as dealers and agents to provide consumers with standardized SIMAGIC warranty services to safeguard consumers’ legal rights. For information on authorized dealers, please visit www.simagic.com/experience. SIMAGIC adheres to a service spirit that is responsible for users and ensures user confidence, striving to create the ultimate user experience. Regarding these warranty terms, if adjustments are necessary, we regret that specific notifications may not be provided.
Please refer to the latest content released through official channels such as the official website. Please avoid causing damage to the machine intentionally. Do not deviate from the guidance of official or officially authorized personnel when performing non-normal hardware or system operations on the machine. For detailed usage instructions, please visit www.simagic.com/pro-tutorial .
Disclaimer
The Limited Warranty does not apply to any:
a) Damage to the machine caused by incorrect installation or operation.
b) Repairs, modifications, alterations, or self-replacement of any internal components by non-technical personnel of the company.
c) Alteration of the machine serial number or inconsistencies with this certificate.
d) Damage caused by negligence, water, or infiltration of other substances into the machine. Malfunctions or damage caused by accidents or natural disasters.
e) Users are prohibited from personally opening the machine’s casing, as doing so may void the warranty and other guarantees.
USER MANUAL 14
Neo X
6. Safety Information
In order to achieve maximum safty while using your Neo X , We suggest that you adopt the following guidelines:
· Should you have trouble using the product properly and troubleshootingdoes not work, unplug the power and go to your local distributor for support. Do not attempt to service or fix the product yourself at any time.
· To prevent fire or shock hazard, never expose the wheel to rain or moisture.
· Only use the power and/or accessories included in the package, and/or purchase accessories made and/or approved by the manufacturer.
· Only use AC power provided by a standard wall outlet to avoid damage to the product.
· When terminating use, please turn off the buttons and power equipment to prevent accidents.
· Unplug the unit during a lightning storm or if it will not be used for a long period of time.
· Do not take apart the phone (doing so will void your warranty), component replacements must be carried out or authorized by SIMAGIC’s official repair center.
· Children under 6 years old are prohibited from using this device.
When using the simulator, please pay attention to the following:
· The device has significant force feedback and contains small components. Children under 15 years old are prohibited from operating or using it independently. When in use, parents must adjust the force feedback parameters in child mode and supervise.
· For first-time users, adjust the force feedback gradually to an appropriate level.
· First-time users or those experiencing the device should be guided by the device owner.
· Loose clothing items such as hair, cables, skirts, etc., should be kept away from the simulator.
USER MANUAL 15
Neo X
· If you have a history of epilepsy or seizures, consult a doctor before use. Certain patterns may trigger seizures with no prior history. If you experience any symptoms, please stop using the product immediately and consult a doctor.
· When using a high-torque base, the peak force feedback may cause hand injuries. If the feedback is too strong, release your hands immediately and adjust the feedback intensity parameters promptly to prevent potential accidents.
· The equipment contains moving parts, pinch points, and sharp edges that may cause personal injury. Operate with caution to prevent pinching, bruising, kicking, smashing, or other bodily injuries.
· It is recommended to limit the force feedback gaming time from 20 to 40 mins to avoid health risks from excessive use.
· Users should refrain from driving a real car for at least 1 hour after finishing the game.
· If any abnormalities are detected, stop using the device immediately and seek assistance from SIMAGIC’s official or authorized service center.
· Please follow SIMAGIC’s official website and public platforms for the latest product information.
USER MANUAL 16
6. Contact us
Discord
Neo X
USER MANUAL 17
Neo X
FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Discord NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ·Reorient or relocate the receiving antenna. ·Increase the separation between the equipment and receiver. ·Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ·Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
ICnopsytriaghgtr©a2m024 SIMAGIC Tech Co.Ltd. All Rights Reserved.
The products and corporate names mentioned in this manual may or may not be registered trademarks or copyrights of their respective companies. They are used solely for the purposes of identification or explanation, and to the benefit of the owners, without any intention of infringement. The specifications and information provided in this manual are intended for informational purposes only and are subject to change at any time without notice. They should not be interpreted as a commitment by SIMAGIC. SIMAGIC assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual, including those related to the products and software described within it. SIMAGIC shall not be liable for any lost profits, loss of information or data, special, incidental, indirect, punitive, or consequential damages arising in any way out of the distribution, sale, resale, use, or inability to use the Product. In no event shall Simagic’s liability exceed the retail purchase price of the Product.
USER MANUAL 18
Documents / Resources
 |
SIMAGIC Neo X Compact High End Button Hub [pdf] User Manual 2AWJ8-NEOX, 2AWJ8NEOX, Neo X Compact High End Button Hub, Neo X, Compact High End Button Hub, High End Button Hub, Button Hub |