Prestel KB-RS1 Intelligent PTZ Keyboard Controller

intelligent PTZ keyboard controller

Prompt
No unit or individual is allowed to produce all or part of the copy, regeneration or translateinto other machine readable form of electronic media; This manual might be not accurate technically or contains some minor typo errors. The contents in this manual about production description and program might be updated on an un-periodical.

Cautions
The LCD is fragile, no crush or long-exposed under strong light. Joystick is fragile, please make sure product is packed with original packing material when you send it back for reparation. The keyboard controller should be work in specified range of temperature and humidity. Please follow the onnecting method defined in this manual.

Keyboard Controller Parameters

List Of Items 

KEYBOARD FRONT BOARD INTRODUCTION 

1. Function Keys On Front Panel

• Joystick
• LCD screen
• Function keys
• Speed dome Setup and recall keys

Introduction

• [Esc] exit key: exit and back to previous menu;
• [Setup] setup key: press and hold for 3s to setup keyboard’s parameter.
• [Fl] adjust the control speed, it has 4 level : 1, 2, 3, 4;
• [Preset] preset special status of ptz(including direction and zoom times): this key should be used together with number key;
• [Shot] recall special status of ptz(including direction and zoom times) : this key should be used together with number key;
• [Pattern] start/stop pattern record: press for 3 seconds to start pattern record, after all operation, press this key again to stop pattern record, this key should be used together with number key
• [Run] start/stop pattern record: press for 3 seconds to start pattern record, after all operation, press this key again to stop pattern record, this key should be used together with number key
• [0] ~ [9] number key: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9
• [Auto] control ptz rotate in horizontal direction automatically or clear input number: when user input some numbers, press this key can delete the numbers, else it will control ptz rotate in horizontal direction automatically;
• [Cam] control ptz rotate in horizontal direction automatically or clear input number: when user input some numbers, press this key can delete the numbers, else it will control ptz rotate in horizontal direction automatically;
• [Tele] zoom in : zoom in the object, enlarge the object size;
• [Wide]  zoom out : zoom out the object, reduce the object size;
• [Open]  iris + : enlarge iris;
• [Close]  iris – : reduce iris;
•  [Far]  focus+ : adjust the lens focus on distant object;
• [Near] focus-: adjust the lens focus on near object;
• [Aux on]  aux on : turn on ptz’s aux. function, this key should be used together with number key; directly press this key without keying in any number, the controlled ptz ID will add 1.
• [Aux off] aux off: turn off ptz’s aux. function, this key should be used together with number key; directly press this key without keying in any number, the controlled ptz ID will take away 1.
• [press joystick] press and hold for 3s to recall number 95 preset, normally it will be opening the menu of ptz.

LCD Screen
Press each function key, LCD screen will show relevant information, press And hold the key, relevant information will show while release it will disappear. When there is no operation over 30s, it will get into power-save mode(its backllght will be turned off), it will show standby image, details as bellow:

Joystick Control

When control speed dome and mounting plate:

KEYBOARD CONTROLLER OPERATIONS

• Introduction To single-press Keys And Combined Keys
• Single-press key: When single key is pressed, the corresponding PTZ will respond. Single-press keys include: [Near], [Far], [Tele], [Wide], [Open], [Close], [Auto] , [Fll , [Run] , [Escl ,joystick.
• Combined key operations mean 2 or more keys, or key and joystick are pressed, the corresponding PTZ will respond.
• The operations Include: [Preset] , [Pattern] , [Shot] , [Cam] , [Setup] .

Detailed introduction to combined keys

• Select PTZ ID: select speed dome or decoder whose ID is 28: press [21 , [8] , [Caml in turn, LCD will display as below(corresponding protocol and baud rate will also be showed)

set and recall pattern:
Set pattern: select PTZ addr., press [pattern] key and hold for more than 3s,

LCD will display:

Operate joystick to control PTZ moving to relevant position, adjust zoom time. After setup, press [pattern] key to finish, LCD will display:

• Recall pattern : press [Run) key,PTZ will run in the certain route which recorded in relevant pattern;
• Press any single-press key will stop pattern scan and back to normal status;

Note: This keyboard supports setting one pattern at present.

set and recall preset point:

• Set preset point 1: key in [1) , press [Preset) .
• Recall preset point 2: key in [2) , press [Shot) .

Turn on/Turn off aux function

• Turn on: need to open number 1 aux. function, press [1), press [AUX on).
• Turn off: need to close number 1 aux. function, press [1), press [AUX off)

PARAMETER SETUP AND INQUIRY

Parameter Setup And Inquiry

e.g.: change the protocol of PTZ 28 to PelcoP, baud rate to 9600. in normal status, press and hold [setup] key for more than 3s, LCD will display:

key in password (default: 8888) , press joystick, LCD will display:

Press joystick, LCD will display:

Move the joystick toward left/right to select PTZ 28, LCD will display:

Move the joystick toward right, LCD will display:

Press joystick, finish protocol setup and switch to baud rate setup, LCD will display

Move the joystick toward right till LCD display:

Press joystick, finish setup and back to select PTZ ID menu, repeat above steps, you can set other PTZ parameter after finishing all setup, press [ESC] key to quit setup. Note: If you want to set all PTZ’s protocol and baud rate as same, when you select PTZ ID in setup menu, please select 0-255, details as below:

Follow above steps, all PTZ’s protocol and baud rate will be set as same.

System Parameter Setup

System parameter including : language, password, key-press volumn, key backlight, default factory setupo The following example is “default factory setup”operation steps: In normal status, press and hold [setup] key for more than 3s, LCD will Display:

Key in password (default password: 8888) , press joystick, LCD will display:

Move the joystick toward down, LCD will display:

Press joystick, LCD will display:

Move joystick till LCD display:

Move joystick toward right, LCD will display:

Press joystick, the buzzer will give out long time sound, the question mark”?” in screen will disappear, denote setup finished, press [E5C] key to quit setup.

Parameter Setup Framework:

TYPICAL CONNECTING DIAGRAM

Typical connecting diagram

FAQs

Documents / Resources

Prestel KB-RS1 Intelligent PTZ Keyboard Controller [pdf] User Manual KB-RS1, KB-RS1 Intelligent PTZ Keyboard Controller, Intelligent PTZ Keyboard Controller, PTZ Keyboard Controller, Keyboard Controller, Controller

References

• User Manual