DL-CH12 Version 1 Harness
“
Product Specifications
- Make: DL-CH12 Jeep Cherokee PTS
- Model Year: 2019-2022
- Install Type: 6
- CAN BCM Lights: Park / Auto
- Type: B2
- IGN: PINK
Product Usage Instructions
Module Programming Procedure – PTS
NOTE: The hood must be closed before starting
the programming procedure.
- Close the driver door and then re-open it to wake up the data
bus. - Press UNLOCK on the OEM remote. If there is no OEM remote,
press on the module programming button. - Wait for the LED to flash BLUE once. If it flashes GREEN,
repeat step 2. - Set ignition to OFF position.
- Disconnect the module from the vehicle by following the
specified steps. - Connect the module to a computer for extended programming.
- Repeat steps 4 to 6 eight times.
- Set ignition to ON position.
- Wait for the LED to flash BLUE rapidly, indicating completion
of the Module Programming Procedure.
Take Over Procedure – PTS – To The Vehicle Owner
NOTE: All vehicle doors must be closed and
locked before initiating the remote start sequence.
- All vehicle doors must be closed and locked before starting the
remote start sequence. - Within 45 seconds from the previous step, open the vehicle
door, enter the vehicle, and close the vehicle door.
Frequently Asked Questions (FAQ)
Q: What should I do if the LED does not flash GREEN during the
Module Programming Procedure?
A: If the LED does not flash GREEN, repeat step 2 by pressing
UNLOCK on the OEM remote or the module programming button.
Q: Can I skip any steps in the Module Programming
Procedure?
A: No, it is important to follow each step of the Module
Programming Procedure as outlined in the user manual to ensure
successful programming.
“`
FTI-CDP1: Notas de preparación y cobertura del vehículo
Make
Model
DL-CH12 Jeep Cherokee PTS
Year 2019-22
Install Type 6
CAN BCM
Lights
Park / Auto
Type B2
IGN PINK
RAP I/O Changes
Green White/Blue
NO N/A
FIRMWARE: Esta instalación requiere el firmware BLADE-AL (DL) -CH12, el módulo flash y la actualización del firmware del controlador antes de la instalación.
INSTALACIÓN: Las conexiones CAN Tipo 6 utilizan el cable de extensión CAN opcional para obtener datos del BCM del vehículo, conector C4 (CANL, pin # 37, amarillo, CANH, pin # 38, marrón)
ENCENDIDO: El encendido tipo 6 se encuentra en el conector C4 del BCM (conector de 60 clavijas, clavija n. ° 3, marrón). Precaución, la identificación adecuada de los circuitos es crucial, hay dos (2) cables marrones en el mismo conector utilizado para esta instalación.
FTI-CDP1 – Notas de instalación y configuración
A CONEXIÓN REQUERIDA (cable de extensión CAN) B NO REQUERIDO (OBD-CAN) C SIN CONEXIÓN D CONEXIÓN REQUERIDA (IGN) E PRECAUCIÓN: CONFIRME LA POSICIÓN DEL CIRCUITO (2 cables marrones) CM7000/7200 Cut loop for A/T
CM7X00
IIIIIIIIIIIIIIIIIIIIIIEIIIRIIIIIIIIIIIIIIIIIIIIIIIIIIIII
D LAN
2001
O
O
Z
K E R E D
st. E
IIIIIIIII
S
ID
D
KO O
rG
fo AD E
R R
E ‘T T AN NC
CE AND
WHO
O H W
WANNA
LEARN
TO
IIIIIIIII
COBFEERATTUURRAE DCEOVFEURNACGIOENES
CM-900S/900AS
CM900AS/900S Jumper
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII D
O OTHER STUFF GOOD TOO
IMMOBILIZER DATA ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK TRUNK/HATCH RELEASE POWER LIFTGATE POWER SLIDING DOOR (L) POWER SLIDING DOOR (R) SECURE TAKEOVER DOOR STATUS TRUNK STATUS HOOD STATUS E-BRAKE STATUS TACH OUTPUT BRAKE STATUS GLOW PLUG STATUS PARKING LIGHTS HAZARD LIGHTS A/M CONTROL
CM -900
FTI-CDP1 – DL-CH12 – Type 6 2019-22 Jeep Cherokee PTS
BLADE
PWR
pink/black
C
green pink
A
B
B
3
2
4
1
OBD-II connector 1
1
16
PTS Button 2
ENGINE START STOP
Headlight switch
3
AUTO
*Not required
BCM 4
RAP SHUTDOWN
(FRONT VIEW)
C4 – BLACK
46 31
16 1
3
*tan/pink
brown* 37
yellow
38
brown
E
D
60 45
30 15
Códigos de error de programación de LED
El LED del módulo parpadea en ROJO durante la programación
1x – Error de CAN 2x – Código clave no aprendido 3x – Sin ENCENDIDO 4x – Sin inmovilizador, comprobar CAN / llave 5x – Error de VIN, verifique el cableado CAN 6x – Ver error 4x 7x – Error de KLON 8x – Sin ENCENDIDO, verifique la conexión
INSTALL GUIDE
ALL IN ONE
CHRYSLER/FIAT/JEEP
Patent No. US 8,856,780 CA 2759622
Page 40 of 43
COM-BLADE-AL(DL)-CH12-EN
Doc. No.: ##72849## 20201120
MODULE PROGRAMMING PROCEDURE – PTS
NOTE
I IMPORTANT: The hood must be closed.
1
Close driver door. Re-open driver door to wake up
data bus.
2
Press UNLOCK on OEM remote.
(If the vehicle is not equipped
with an OEM remote, press
on the module programming
button.)
3
Wait, LED will flash BLUE once [1x]. If LED does not flash
GREEN, repeat step 2.
10 OFF ACC ON START
ENGINE START STOP
Set ignition to OFF position.
11
WARNING: Disconnect power last. Disconnect module from vehicle.
12
Connect module to computer and proceed with extended programming.
4
OFF ACC ON START
Set ignition to ON position.
ENGINE START STOP
13
WARNING: Do not press module programming button. Connect power first. Connect module to vehicle.
5
6
OFF ACC ON START
Wait, if LED turns solid RED proceed to step 6. If LED flashes BLUE rapidly, proceed to step 10.
Set ignition to OFF position.
ENGINE START STOP
14 OFF ACC ON START
Set ignition to ON position.
ENGINE START STOP
15
Wait, LED will turn solid BLUE for 2 seconds.
7
Repeat steps 4 to 6, eight times [8x].
8
OFF ACC ON START
Set ignition to ON position.
ENGINE START STOP
16 OFF ACC ON START
ENGINE START STOP
Set ignition to OFF position.
17
Module Programming Procedure completed.
9
Wait, LED will flash BLUE rapidly.
WWW.IDATALINK.COM
Automotive Data Solutions Inc. © 2020
INSTALL GUIDE
ALL IN ONE
CHRYSLER/FIAT/JEEP
Page 43 of 43
Patent No. US 8,856,780 CA 2759622
COM-BLADE-AL(DL)-CH12-EN
Doc. No.: ##72849## 20201120
WARNING: READ BEFORE RNEOMTOICTEE STARTING THE VEHICLE
IMPORTANT
I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction.
TAKE OVER PROCEDURE – PTS – TO THE VEHICLE OWNER
NOTE
2
I All vehicle doors must be closed and locked prior to remote start sequence.
TIME RESTRICTI N COMING UP !
TIME RESTRICTI N
Within 45 SECONDSfrom previous step:
Open vehicle door. Enter vehicle. Close vehicle door.
Press and release BRAKE pedal.
1
Unlock vehicle door using OEM or after-market remote, or door
request switch.
3
Take over procedure completed.
!
Failure to follow procedure will result in vehicle engine shutdown.
WWW.IDATALINK.COM
Automotive Data Solutions Inc. © 2020
Documents / Resources
 |
myFirstech DL-CH12 Version 1 Harness [pdf] Instruction Manual DL-CH12, CM7X00, CM-900, CM-900AS-900S, DL-CH12 Version 1 Harness, DL-CH12, Version 1 Harness, 1 Harness, Harness |
 |
myFirstech DL-CH12 Version 1 Harness [pdf] Instruction Manual CH12, DL-CH12, DL-CH12 Version 1 Harness, DL-CH12, Version 1 Harness, 1 Harness, Harness |
