BLINDER ARRAY FC
TWO-EYED AUDIENCE CUBE
USER MANUAL
Blinder Array FC
PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE
When this product leaves the factory, its performance is intact and its packaging is complete. All users should strictly abide by the warnings and operating instructions stated in this manual. Any damage caused by misuse is not covered by the company’s warranty, and the dealer is not responsible for faults and problems caused by ignoring the operating manual. .
This manual is subject to technical changes without prior notice.
SAFETY INSTRUCTIONS
When unpacking and before disposing of the carton check there is no transportation damage before using the light. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.
The projector is for indoor and outdoor use, IP65.
Do not install the fixtures onto inflammable surfaces directly.
The fixture is only intended for installation, operation and maintenance by qualified personnel.
Do not project the beam onto inflammable surfaces, minimum distance is 5meter. 5m
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle and/or modify the projector in any way.
Ensure that there are no obstructions in the light-emitting direction, to ensure that the light of the lamp beads will not be reflected back, to avoid the backlog of heat, and burn out the lamp beads and optical devices
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power requirements of the fixture.
It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.
POWER
Do not connect this device to any other types of dimmer apparatus.
The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it should be attached as shown in “installing the projector” section.
Shields and lens shall be changed if they have become visibly damaged to such an extent than their effectiveness is impaired, for example by cracks or deep scratches.
Exterior surface temperatures of the luminaire after 5 minutes operation is 45 °C, when steady state is achieved 70 °C.
There is no user serviceable parts inside the projector, do not open the housing and never operate the fixture with the covers removed.
If you have any questions, don’t hesitate to consult your dealer or manufacturer.
LAMP STRUCTURE AND INSTALLATION
DMX
In order to reduce signal errors and avoid signal weakening and interference during transmission,
You can add a 120 ohm 1/4W resistor between pins 2 and 3 of the DMX output of the last machine.
- Connect the lamp with an XLR signal cable, and connect one end to the output port of the lamp.
Connect the other end to the input port of the next light fixture. Signal lines can only be used for series connection, not parallel connection.
Because the DMX512 signal transmission speed is very fast, when the signal line is damaged, the welding joint is not strong, the contact is not good,etc.,
It will affect signal transmission and cause the system to shut down.
- When the machine power to a unit is disconnected, the DMX output and input connections are bypassed.
In order to maintain the connectivity of the DMX line.
- When the machine power to a unit is disconnected, the DMX output and input connections are bypassed.
In order to maintain the connectivity of the DMX line.
- The terminal of the DMX512 system needs to be equipped with a terminator to reduce signal transmission errors.
DMX ADDRESS CODE SETTINGS
| CH | ADDRESS | First address | Second address | Third address | 4th address |
| 1CH | 001-001 | 001 | 002 | 003 | 004 |
| 2CH | 001-002 | 001 | 003 | 005 | 007 |
| 4CH | 001-004 | 001 | 005 | 009 | 013 |
| 6CH | 001-005 | 001 | 006 | 011 | 016 |
| 9CH | 001-007 | 001 | 008 | 015 | 022 |
| 10CH | 001-010 | 001 | 011 | 021 | 031 |
| 12CH | 001-012 | 001 | 013 | 025 | 037 |
| 13CH | 001-013 | 001 | 014 | 027 | 040 |
| 14CH | 001-014 | 001 | 015 | 029 | 043 |
| 17CH | 001-017 | 001 | 018 | 035 | 052 |
| 22CH | 001-022 | 001 | 023 | 045 | 067 |
| 24CH | 001-024 | 001 | 025 | 049 | 073 |
| 28CH | 001-028 | 001 | 029 | 057 | 085 |
| 33CH | 001-033 | 001 | 034 | 067 | 100 |
(Refer to the picture above) The number of lamps added after the fourth one; the address code is based on the channel, and so on.
CABLE CONNECTION
Power in/out
Connect the power cord hand in hand
Note: Due to power reasons, a 1.5 square power cord
Can bring up to 6 units (230V)
WARNING
- Do not connect too many lamps to a single power cord or overload it.
- Do not use power cords with damaged insulation, and do not place power cords on other conductors.
- When the lamp is not in use or when cleaning, please unplug the power cord.
- Do not pull or pull the power cord vigorously.
CONTROL PANEL
A. Power input: IP65 waterproof POWER IN power cord Input voltage: 100-240V 50/60HZ
B. Power output: IP65 waterproof POWER OUT power cable output voltage 100-240V 50/60HZ
C. DMX input: IP68 3-core DMX IN waterproof signal line input
D. DMX output: IP65 3-core DMX OUT waterproof signal line output
E. IP65 USB port for firmware updates
F. Safety hook
G. The panel function operations are as follows:
DISPLAY PANEL FUNCTION DESCRIPTION
|
FUNCTION |
DESCRIPTION | Function description |
Effect |
| ESC (Function keys) | Menu selection | Enter menu selection function | Menu operation |
 (Up key) |
up | Go to previous option | Change parameters to increase |
 (down) |
down | Go to the next option | Changing parameters reduces |
| ENTER (confirm) | confirm | Confirm selected function | Save last parameter |
|
Primer nivel del menú |
Segundo nivel del menú |
Tercer nivel del menú |
|
| 1 DMX ADDRESS | 001-512 | ||
| cancel | |||
| confirm | |||
| 2 DMX Channel mode | 1 CH DWE | ||
| 2 CH DWE | |||
| 4 CH DWE | |||
| 9CH DWE+ | |||
| 6CH STROBE | |||
| 6CH RGB | |||
| 10CH BASIC RGB | |||
| 14CH BASIC RGB | |||
| 13CH STANDARD RGB | |||
| 22CH STANDARD RGB | |||
| 24CH EXTENDED RGB | |||
| 24CH EXTENDED RGB | |||
| 10CH DIRECT | |||
| 12CH DIRECT | |||
| 17CH DIRECT | |||
| 28CH DIRECT | |||
| 41CH DIRECT | |||
| 3 Manual control | Stop manual | ||
| Self-propelled mode | Stop built-in program | ||
| built-in program1 | |||
| built-in programs2 | |||
| built-in programs3 | |||
| built-in programs4 | |||
| built-in programs5 | |||
| built-in programs6 | |||
| built-in programs7 | |||
| built-in programs8 | |||
| built-in programs9 | |||
| built-in programs10 | |||
| color macro | Turn off color macros | ||
| Dimming | |||
| color macro | |||
| Light up quickly | Dimming | ||
| STROBE | |||
| RED | |||
| GREEN | |||
| BLUE | |||
| AMBER | |||
| WHITER | |||
| Color Temperature | Dimming | ||
| strobe | |||
| Color temperature | |||
| Reddish green | |||
| Custom color | Color1 | ||
| Color2 | |||
| Color3 | |||
| Color4 | |||
| Color5 | |||
| Color set up | calibration mode | ||
| solid color mode | |||
| 4 (Language) | Chinese | ||
| English | |||
| 5 slave mode | slave mode | ||
| 6 fixture settings | display setting | Display inverted | |
| Display off setting | |||
| Automatically lock screen | |||
| startup mode | DMX | ||
| Self-propelled | |||
| Light up quickly | |||
| signal hold | Keep | ||
| black field | |||
| Zenryo | |||
| dimming curve | Linear | ||
| index | |||
| logarithm | |||
| S curve | |||
| Dimming delay | LED | ||
| Medium | |||
| Halogen | |||
| DTW Consecrate | off | ||
| on | |||
| white balance | white balance | ||
| user defined | |||
| Dimming frequency | 800Hz | ||
| 1200Hz | |||
| 2000Hz | |||
| 3600Hz | |||
| 12000Hz | |||
| 25000Hz | |||
| Fan mode | auto | ||
| quiet | |||
| off | |||
| Light order | off | ||
| on | |||
| Transfer settings | Carry DMX | ||
| Not carried DMX | |||
| Power settings | low power | ||
| High power | |||
| USB | off | ||
| on | |||
| Factory settings | reset | ||
| Restore user customiza- tion | |||
| User-defined list |
DMX CHANNEL TABLE
| CH | 1CH DWE | 2CH DWE | 4CH DWE | 9CH DWE+ | 6CH STROBE |
| 1 | Dimmer | Dimmer1 | Dimmer 1 | Master Dimmer | Master Dimmer |
| 2 | Dimmer2 | Dimmer Curve | Shutter | Shutter | |
| 3 | Dimmer Response | Red | Duration | ||
| 4 | Redshift | Green | Dimmer 1 | ||
| 5 | Blue | Dimmer 2 | |||
| 6 | CTC | CTC | |||
| 7 | Dimmer Curve | ||||
| 8 | Dimmer Response | ||||
| 9 | Redshift |
|
CH |
6CH RGB | 10CH BASIC RGB | 14CH BASIC RGB | 13CH STANDARD RGB |
6CH STROBE |
| 1 | Red 1 | Master Dimmer | Master Dimmer | Master Dimmer | Master Dimmer |
| 2 | Green 1 | Shutter | Master Dimmer Fine | Shutter | Shutter |
| 3 | Blue 1 | Red | Shutter | Dimmer 1 | Duration |
| 4 | Red 2 | Green | Red | Red 1 | Dimmer 1 |
| 5 | Green 2 | Blue | Red Fine | Green 1 | Dimmer 2 |
| 6 | Blue 2 | CTC | Green | Blue 1 | CTC |
| 7 | Tint | Green Fine | Dimmer 2 | ||
| 8 | Color Macro | Blue | Red 2 | ||
| 9 | Color Macro Crossfade | Blue Fine | Green 2 | ||
| 10 | Device Settings | CTC | Blue 2 | ||
| 11 | Tint | CTC (all) | |||
| 13 | Color Marco | Tint (all) | |||
| 13 | Color Macro Crossfade | Device Settings | |||
| 14 | Device Settings |
|
CH |
22CH STANDARD RGB | 24CH EXTENDED RGB |
33CH EXTENDED RGB |
| 1 | Master Dimmer | Master Dimmer | Master Dimmer |
| 2 | Master Dimmer Fine | Shutter | Master Dimmer Fine |
| 3 | Shutter | Duration | Shutter |
| 4 | Dimmer 1 | Dimmer 1 | Duration |
| 5 | Dimmer 1 Fine | Red 1 | Dimmer 1 |
| 6 | Red 1 | Green 1 | Dimmer 1 Fine |
| 7 | Red 1 Fine | Blue 1 | Red 1 |
| 8 | Green 1 | CTC 1 | Red 1 Fine |
| 9 | Green 1 Fine | Tint 1 | Green 1 |
| 10 | Blue 1 | Color Macro 1 | Green 1 Fine |
| 11 | Blue 1 Fine | Color Macro Crossfade 1 | Blue 1 |
| 12 | Dimmer 2 | Dimmer 2 | Blue 1 Fine |
| 13 | Dimmer 2 Fine | Red 2 | CTC 1 |
| 14 | Red 2 | Green 2 | Tint 1 |
| 15 | Red 2 Fine | Blue 2 | Color Macro 1 |
| 16 | Green 2 | CTC 2 | Color Macro Crossfade 1 |
| 17 | Green 2 Fine | Tint 2 | Dimmer 2 |
| 18 | Blue 2 | Color Macro 2 | Dimmer 2 Fine |
| 19 | Blue 2 Fine | Color Macro Crossfade 2 | Red 2 |
| 20 | CTC (all) | Effect | Red 2 Fine |
| 21 | Tint (all) | Dimmer Curve | Green 2 |
| 22 | Device Settings | Dimmer Response | Green 2 Fine |
| 23 | Redshift | Blue 2 | |
| 24 | Device Settings | Blue 2 Fine | |
| 25 | CTC 2 | ||
| 26 | Tint 2 | ||
| 27 | Color Macro 2 | ||
| 28 | Color Macro Crossfade 2 | ||
| 29 | Effect | ||
| 30 | Dimmer Curve | ||
| 31 | Dimmer Response | ||
| 32 | Redshift | ||
| 33 | Device Settings |
|
CH |
10CH DIRECT | 12CH DIRECT | 17CH DIRECT | 28CH DIRECT |
41CH DIRECT |
| 1 | Red 1 | Master Dimmer | Master Dimmer | Master Dimmer | Master Dimmer |
| 2 | Green 1 | Shutter | Shutter | Shutter | Master Dimmer Fine |
| 3 | Blue 1 | Red | Dimmer 1 | Duration | Shutter |
| 4 | Amber 1 | Green | Red 1 | Dimmer 1 | Duration |
| 5 | White 1 | Blue | Green 1 | Red 1 | Dimmer 1 |
| 6 | Red 2 | Amber | Blue 1 | Green 1 | Dimmer 1 Fine |
| 7 | Green 2 | White | Amber 1 | Blue 1 | Red 1 |
| 8 | Blue 2 | CTC | White 1 | Amber 1 | Red 1 Fine |
| 9 | Amber 2 | Tint | Dimmer 2 | White 1 | Green 1 |
| 10 | White 2 | Color Macro | Red 2 | CTC 1 | Green 1 Fine |
| 11 | Color Macro Crossfade | Green 2 | Tint 1 | Blue 1 | |
| 12 | Device Settings | Blue 2 | Color Macro 1 | Blue 1 Fine | |
| 13 | Amber 2 | Color Macro Crossfade 1 | Amber 1 | ||
| 14 | White 2 | Dimmer 2 | Amber 1 Fine | ||
| 15 | CTC (all) | Red 2 | White 1 | ||
| 16 | Tint (all) | Green 2 | White 1 Fine | ||
| 17 | Device Settings | Blue 2 | CTC 1 | ||
| 18 | Amber 2 | Tint 1 | |||
| 19 | White 2 | Color Macro 1 | |||
| 20 | CTC 2 | Color Macro Crossfade 1 | |||
| 21 | Tint 2 | Dimmer 2 | |||
| 22 | Color Macro 2 | Dimmer 2 Fine | |||
| 23 | Color Macro Crossfade 2 | Red 2 | |||
| 24 | Effect | Red 2 Fine | |||
| 25 | Dimmer Curve | Green 2 | |||
| 26 | Dimmer Res- ponse | Green 2 Fine | |||
| 27 | Redshift | Blue 2 | |||
| 28 | Device Settings | Blue 2 Fine | |||
| 29 | Amber 2 | ||||
| 30 | Amber 2 Fine | ||||
| 31 | White 2 | ||||
| 32 | White 2 Fine | ||||
| 33 | CTC 2 | ||||
| 34 | Tint 2 | ||||
| 35 | Color Macro 2 | ||||
| 36 | Color Macro Crossfade 2 | ||||
| 37 | Effect | ||||
| 38 | Dimmer Curve | ||||
| 39 | Dimmer Res- ponse | ||||
| 40 | Redshift | ||||
| 41 | Device Settings |
1CH DWE
|
CH |
Function | Value | Percent/Setting |
Remark |
| 1 | Dimmer | 000-255 | 0 – 100% |
2CH DWE
|
CH |
Function | Value | Percent/Setting |
Remark |
| 1 | Dimmer1 | 000-255 | 0 – 100% | |
| 2 | Dimmer2 | 000-255 | 0 – 100% |
2CH DWE
| CH | Function | Value | Percent/Setting | Remark |
| 1 | Dimmer | 000-255 | 0 – 100% | |
| 2 | Dimmer Curve | 000-51 | No Function – Current Preset from Menu Settings | |
| 052-101 | Linear Dimmer Curve | |||
| 102-152 | Exponential Dimmer Curve | |||
| 153-203 | Logarithmic Dimmer Curve | |||
| 204-255 | S-Curve Dimmer Curve | |||
| 3 | Dimmer Response | 000-063 | No Function – Current Preset from Menu Settings | |
| 064-127 | LED / fast | |||
| 128-191 | Medium | |||
| 192-255 | Halogen / slow | |||
| 4 | Redshift | 000-084 | No Function – Current Preset from Menu Settings | |
| 085-170 | Redshift Off | |||
| 171-255 | Redshift On |
9CH DWE+
| CH | Function | Value | Setting |
| 1 | Master Dimmer | 000-255 | 0 – 100% |
| 2 | Shutter | 0-19 | Shutter close |
| 20-24 | Shutter open | ||
| 25-64 | Strobe 1 (fast → slow) | ||
| 65-69 | Shutter open | ||
| 70-84 | Strobe 2: opening pulse (fast slow) | ||
| 85-89 | Shutter open | ||
| 90-104 | Strobe 3: closing pulse (fast slow) | ||
| 105-109 | Shutter open | ||
| 110-124 | Strobe 4: random strobe (fast slow) | ||
| 125-129 | Shutter open | ||
| 130-144 | Strobe 5: random opening pulse (fast slow) | ||
| 145-149 | Shutter open | ||
| 150-164 | Strobe 6: random closing pulse (fast slow) | ||
| 165-169 | Shutter open | ||
| 170-184 | Strobe 7: burst pulse (fast slow) | ||
| 185-189 | Shutter open | ||
| 190-204 | Strobe 8: random burst pulse (fast slow) | ||
| 205-209 | Shutter open | ||
| 210-224 | Strobe 9: sine wave (fast slow) | ||
| 225-229 | Shutter open | ||
| 230-244 | Strobe 10: burst (fast slow) | ||
| 245-255 | Shutter open | ||
| 3 | Red | 000-255 | 0-100% |
| 4 | Green | 000-255 | 0-100% |
| 5 | Blue | 000-255 | 0-100% |
| 6 | CTC (affects RGB) | 000 – 004 | 2900K |
| 005-226 | 2000K-6500K linear in 20-21K steps (please see detailed CTC chart) | ||
| 182-182 | 5600K | ||
| 226-226 | 6500K | ||
| 227-255 | 6621K-10.000K linear in 120-121K steps (please see detai- led CTC chart) | ||
| 7 | Dimmer Curve | 000-051 | No Function – Current Preset from Menu Settings |
| 052-101 | Linear Dimmer Curve | ||
| 102-152 | Exponential Dimmer Curve | ||
| 153-203 | Logarithmic Dimmer Curve | ||
| 204-255 | S-Curve Dimmer Curve | ||
| 8 | Dimmer Response | 000-063 | No Function – Current Preset from Menu Settings |
| 064-127 | LED / fast | ||
| 128-191 | Medium | ||
| 192-255 | Halogen / slow | ||
| 9 | Redshift | 000-084 | No Function – Current Preset from Menu Settings |
| 085-170 | Redshift Off | ||
| 171-255 | Redshift On |
6CH STROBE MODE
|
CH |
Function | Value |
Setting |
| 1 | Master Dimmer | 000-255 | 0 – 100% |
| 2 | Shutter | 0-19 | Shutter close |
| 20-24 | Shutter open | ||
| 25-64 | Strobe 1 (fast → slow) | ||
| 65-69 | Shutter open | ||
| 70-84 | Strobe 2: opening pulse (fast slow) | ||
| 85-89 | Shutter open | ||
| 90-104 | Strobe 3: closing pulse (fast slow) | ||
| 105-109 | Shutter open | ||
| 110-124 | Strobe 4: random strobe (fast slow) | ||
| 125-129 | Shutter open | ||
| 130-144 | Strobe 5: random opening pulse (fast slow) | ||
| 145-149 | Shutter open | ||
| 150-164 | Strobe 6: random closing pulse (fast slow) | ||
| 165-169 | Shutter open | ||
| 170-184 | Strobe 7: burst pulse (fast slow) | ||
| 185-189 | Shutter open | ||
| 190-204 | Strobe 8: random burst pulse (fast slow) | ||
| 205-209 | Shutter open | ||
| 210-224 | Strobe 9: sine wave (fast slow) | ||
| 225-229 | Shutter open | ||
| 230-244 | Strobe 10: burst (fast slow) | ||
| 245-255 | Shutter open | ||
| 3 | Duration | 000-255 | only affects to channel 2 – Strobe 1 025-064 |
| 4 | Dimmer1 | 000-255 | 0-100% |
| 5 | Dimmer2 | 000-255 | 0-100% |
| 6 | CTC | 000-004 | 5600K |
| 005-182 | 2000K-6500K linear in 20-21K steps (please see detailed CTC chart) | ||
| 182-182 | 5600K | ||
| 226-226 | 6500K | ||
| 227-255 | 6621K-10.000K linear in 120-121K steps (please see detailed CTC chart) |
10CH BASIC RGB
|
CH |
Function | Value |
Setting |
| 1 | Master Dimmer | 000-255 | 0 – 100% |
| 2 | Shutter | 0-19 | Shutter close |
| 20-24 | Shutter open | ||
| 25-64 | Strobe 1 (fast → slow) | ||
| 65-69 | Shutter open | ||
| 70-84 | Strobe 2: opening pulse (fast slow) | ||
| 85-89 | Shutter open | ||
| 90-104 | Strobe 3: closing pulse (fast slow) | ||
| 105-109 | Shutter open | ||
| 110-124 | Strobe 4: random strobe (fast slow) | ||
| 125-129 | Shutter open | ||
| 130-144 | Strobe 5: random opening pulse (fast slow) | ||
| 145-149 | Shutter open | ||
| 150-164 | Strobe 6: random closing pulse (fast slow) | ||
| 165-169 | Shutter open | ||
| 170-184 | Strobe 7: burst pulse (fast slow) | ||
| 185-189 | Shutter open | ||
| 190-204 | Strobe 8: random burst pulse (fast slow) | ||
| 205-209 | Shutter open | ||
| 210-224 | Strobe 9: sine wave (fast slow) | ||
| 225-229 | Shutter open | ||
| 230-244 | Strobe 10: burst (fast slow) | ||
| 245-255 | Shutter open | ||
| 3 | Red | 000-255 | 0-100% |
| 4 | Green | 000-255 | 0-100% |
| 5 | Blue | 000-255 | 0-100% |
| 6 | CTC (affects RGB) | 000 – 004 | 2900K |
| 005-226 | 2000K-6500K linear in 20-21K steps (please see detai- led CTC chart) | ||
| 182-182 | 5600K | ||
| 226-226 | 6500K | ||
| 227-255 | 6621K-10.000K linear in 120-121K steps (please see detailed CTC chart) | ||
| 7 | Dimmer Curve | 000-051 | No Function – Current Preset from Menu Settings |
| 052-101 | Linear Dimmer Curve | ||
| 102-152 | Exponential Dimmer Curve | ||
| 153-203 | Logarithmic Dimmer Curve | ||
| 204-255 | S-Curve Dimmer Curve | ||
| 8 | Dimmer Response | 000-063 | No Function – Current Preset from Menu Settings |
| 064-127 | LED / fast | ||
| 128-191 | Medium | ||
| 192-255 | Halogen / slow | ||
| 9 | 200-214 | Invert Mapping Off (hold 3s) | |
| 215-219 | Invert Mapping On (hold 3s) | ||
| 220-224 | No function | ||
| 10 | 225-229 | LED Mode – Illumination (hold 1,5s) | |
| 230-234 | LED Mode – Boost (hold 1,5s) | ||
| 235-239 | No function | ||
| 240-244 | Factory Reset (hold 3s) Reset only starts if Shutter channel is set to DMX 250 | ||
| 245-249 | User Reset (hold 3s) / Reset only starts if
Shutter channel is set to DMX 250 / no self test by DMX |
||
| 250-255 | No function | ||
| 055-059 | DMX Fail – Emergency Light (hold 3s) | ||
| 060-064 | No function | ||
| 065-069 | Linear Dimmer Curve (hold 1,5s) | ||
| 070-074 | Exponential Dimmer Curve (hold 1,5s) | ||
| 075-079 | Logarithmic Dimmer Curve (hold 1,5s) | ||
| 080-084 | S-Curve Dimmer Curve (hold 1,5s) | ||
| 085-089 | No function | ||
| 090-094 | LED (Fast) Dimmer Response (hold 1,5s) | ||
| 095-099 | Medium Dimmer Response (hold 1,5s) | ||
| 100-104 | Halogen (Slow) Dimmer Response (hold 1,5s) | ||
| 105-109 | No function | ||
| 110-114 | Redshift On (hold 1,5s / affects only between 2700- 3500K ) | ||
| 115-119 | Redshift Off (hold 1,5s) | ||
| 120-124 | No function | ||
| 125-129 | Full Calibration (Colors & CCT / hold 3s) | ||
| 130-134 | CCT Calibration (RAW Colors / hold 3s) | ||
| 135-139 | No function | ||
| 140-144 | LED Frequency 800Hz (hold 3s) | ||
| 145-149 | LED Frequency 1200Hz (hold 3s) | ||
| 150-154 | LED Frequency 2000Hz (hold 3s) | ||
| 155-159 | LED Frequency 3600Hz (hold 3s) | ||
| 160-164 | LED Frequency 12KHz (hold 3s) | ||
| 165-169 | LED Frequency 25KHz (hold 3s) | ||
| 170-174 | No function | ||
| 175-179 | Fan Auto (hold 3s) | ||
| 180-184 | Fan Silent (hold 3s) | ||
| 185-189 | Fan Off (hold 3s) | ||
| 190-194 | Fan High Power (hold 3s) | ||
| 195-199 | No function |
10CH BASIC RGB
| CH | Function | Value | Setting |
| 1 | Master Dimmer | 000-255 | 0 – 100% |
| 2 | Master Dimmer Fine | 000-255 | 0-100% |
| 3 | Shutter | 0-19 | Shutter close |
| 20-24 | Shutter open | ||
| 25-64 | Strobe 1 (fast → slow) | ||
| 65-69 | Shutter open | ||
| 70-84 | Strobe 2: opening pulse (fast slow) | ||
| 85-89 | Shutter open | ||
| 90-104 | Strobe 3: closing pulse (fast slow) | ||
| 105-109 | Shutter open | ||
| 110-124 | Strobe 4: random strobe (fast slow) | ||
| 125-129 | Shutter open | ||
| 130-144 | Strobe 5: random opening pulse (fast slow) | ||
| 145-149 | Shutter open | ||
| 150-164 | Strobe 6: random closing pulse (fast slow) | ||
| 165-169 | Shutter open | ||
| 170-184 | Strobe 7: burst pulse (fast slow) | ||
| 185-189 | Shutter open | ||
| 190-204 | Strobe 8: random burst pulse (fast slow) | ||
| 205-209 | Shutter open | ||
| 210-224 | Strobe 9: sine wave (fast slow) | ||
| 225-229 | Shutter open | ||
| 230-244 | Strobe 10: burst (fast slow) | ||
| 245-255 | Shutter open | ||
| 4 | Red | 000-255 | 0-100% |
| 5 | Red Fine | 000-255 | 0-100% |
| 6 | Green | 000-255 | 0-100% |
| 6 | CTC (affects RGB) | 000 – 004 | 2900K |
| 7 | Green Fine | 000-255 | 0-100% |
| 8 | Blue | 000-255 | 0-100% |
| 9 | Blue Fine | 000-255 | 0-100% |
| 10 | CTC (affects RGB) | 000-004 | 5600K |
| 005-182 | 2000K-6500K linear in 20-21K steps (please see detai- led CTC chart) | ||
| 182-182 | 5600K | ||
| 226-226 | 6500K | ||
| 227-255 | 6621K-10.000K linear in 120-121K steps (please see detailed CTC chart) | ||
| 11 | Tint (affects CTC and RGB) | 0 | no function |
| 000-127 | Magenta -> Neutral | ||
| 128-128 | Neutral | ||
| 129-255 | Neutral -> Green | ||
| 12 | Color Macro (overrideRGB/CTC) | 000-255 | Please see Pomelo color macro chart |
| 13 | Color Macro Cross fade (Transition Time between Color Macros) | 000-005 | No function |
| 006-105 | 0,1s – 10s (0,1s steps) | ||
| 106-214 | 11s – 119s (1s steps) | ||
| 215-244 | 2m – 4m50s (10s steps) | ||
| 245-255 | 5m – 15m (1m steps) | ||
| 14 | Device Settings (please see remark *1) | 000-029 | No function |
| 030-034 | Display Backlight On (hold 3s) | ||
| 035-039 | Display Backlight Off (hold 3s) | ||
| 040-044 | No function | ||
| 045-049 | DMX Fail Blackout (hold 3s) | ||
| 050-054 | DMX Fail Hold (hold 3s) | ||
| 055-059 | DMX Fail – Emergency Light (hold 3s) | ||
| 060-064 | No function | ||
| 065-069 | Linear Dimmer Curve (hold 1,5s) | ||
| 070-074 | Exponential Dimmer Curve (hold 1,5s) | ||
| 075-079 | Logarithmic Dimmer Curve (hold 1,5s) | ||
| 080-084 | S-Curve Dimmer Curve (hold 1,5s) | ||
| 085-089 | No function | ||
| 090-094 | LED (Fast) Dimmer Response (hold 1,5s) | ||
| 095-099 | Medium Dimmer Response (hold 1,5s) | ||
| 100-104 | Halogen (Slow) Dimmer Response (hold 1,5s) | ||
| 105-109 | No function | ||
| 110-114 | Redshift On (hold 1,5s / affects only between 2700-3500K ) | ||
| 115-119 | Redshift Off (hold 1,5s) | ||
| 120-124 | No function | ||
| 125-129 | Full Calibration (Colors & CCT / hold 3s) | ||
| 130-134 | CCT Calibration (RAW Colors / hold 3s) | ||
| 135-139 | No function | ||
| 140-144 | LED Frequency 800Hz (hold 3s) | ||
| 145-149 | LED Frequency 1200Hz (hold 3s) | ||
| 150-154 | LED Frequency 2000Hz (hold 3s) | ||
| 155-159 | LED Frequency 3600Hz (hold 3s) | ||
| 160-164 | LED Frequency 12KHz (hold 3s) | ||
| 165-169 | LED Frequency 25KHz (hold 3s) | ||
| 170-174 | No function | ||
| 175-179 | Fan Auto (hold 3s) | ||
| 180-184 | Fan Silent (hold 3s) | ||
| 185-189 | Fan Off (hold 3s) | ||
| 190-194 | Fan High Power (hold 3s) | ||
| 195-199 | No function | ||
| 200-214 | Invert Mapping Off (hold 3s) | ||
| 215-219 | Invert Mapping On (hold 3s) | ||
| 220-224 | No function | ||
| 225-229 | LED Mode – Illumination (hold 1,5s) | ||
| 230-234 | LED Mode – Boost (hold 1,5s) | ||
| 235-239 | No function | ||
| 240-244 | Factory Reset (hold 3s) Reset only starts if Shutter channel is set to DMX 250 | ||
| 245-249 | User Reset (hold 3s) Reset only starts if Shutter channel is set to DMX 250 / no self test by DMX | ||
| 250-255 | No function |
13CH STANDARD RGB
| CH | Function | Value | Setting |
| 1 | Master Dimmer | 000-255 | 0 – 100% |
| 2 | Shutter | 000-255 | 0 – 100% |
| 0-19 | Shutter close | ||
| 20-24 | Shutter open | ||
| 25-64 | Strobe 1 (fast → slow) | ||
| 65-69 | Shutter open | ||
| 70-84 | Strobe 2: opening pulse (fast slow) | ||
| 85-89 | Shutter open | ||
| 90-104 | Strobe 3: closing pulse (fast slow) | ||
| 105-109 | Shutter open | ||
| 110-124 | Strobe 4: random strobe (fast slow) | ||
| 125-129 | Shutter open | ||
| 130-144 | Strobe 5: random opening pulse (fast slow) | ||
| 145-149 | Shutter open | ||
| 150-164 | Strobe 6: random closing pulse (fast slow) | ||
| 165-169 | Shutter open | ||
| 170-184 | Strobe 7: burst pulse (fast slow) | ||
| 185-189 | Shutter open | ||
| 190-204 | Strobe 8: random burst pulse (fast slow) | ||
| 205-209 | Shutter open | ||
| 210-224 | Strobe 9: sine wave (fast slow) | ||
| 225-229 | Shutter open | ||
| 230-244 | Strobe 10: burst (fast slow) | ||
| 3 | Dimmer 1 | 000-255 | 0-100% |
| 4 | Red 1 | 000-255 | 0-100% |
| 5 | Green1 | 000-255 | 0-100% |
| 6 | Blue1 | 000-255 | 0-100% |
| 7 | Dimmer 2 | 000-255 | 0-100% |
| 8 | Red 2 | 000-255 | 0-100% |
| 9 | Green2 | 000-255 | 0-100% |
| 10 | Blue2 | 000-255 | 0-100% |
| 11 | CTC(affects RGB 1+2) | 000-004 | 5600K |
| 005-182 | 2000K-6500K linear in 20-21K steps (please see detai- led CTC chart) | ||
| 182-182 | 5600K | ||
| 226-226 | 6500K | ||
| 227-255 | 6621K-10.000K linear in 120-121K steps (please see detailed CTC chart) | ||
| 12 | Tint
(affects CTC and RGB) |
0 | no function |
| 000-127 | Magenta -> Neutral | ||
| 128-128 | Neutral | ||
| 129-255 | Neutral -> Green | ||
| 13 | Device Settings (please see remark *1) | 000-029 | No function |
| 030-034 | Display Backlight On (hold 3s) | ||
| 035-039 | Display Backlight Off (hold 3s) | ||
| 040-044 | No function | ||
| 045-049 | DMX Fail Blackout (hold 3s) | ||
| 050-054 | DMX Fail Hold (hold 3s) | ||
| 055-059 | DMX Fail – Emergency Light (hold 3s) | ||
| 060-064 | No function | ||
| 065-069 | Linear Dimmer Curve (hold 1,5s) | ||
| 070-074 | Exponential Dimmer Curve (hold 1,5s) | ||
| 075-079 | Logarithmic Dimmer Curve (hold 1,5s) | ||
| 080-084 | S-Curve Dimmer Curve (hold 1,5s) | ||
| 085-089 | No function | ||
| 090-094 | LED (Fast) Dimmer Response (hold 1,5s) | ||
| 095-099 | Medium Dimmer Response (hold 1,5s) | ||
| 100-104 | Halogen (Slow) Dimmer Response (hold 1,5s) | ||
| 105-109 | No function | ||
| 110-114 | Redshift On (hold 1,5s / affects only bet | ||
| ween 2700-3500K ) | |||
| 115-119 | Redshift Off (hold 1,5s) | ||
| 120-124 | No function | ||
| 125-129 | Full Calibration (Colors & CCT / hold 3s) | ||
| 130-134 | CCT Calibration (RAW Colors / hold 3s) | ||
| 135-139 | No function | ||
| 140-144 | LED Frequency 800Hz (hold 3s) | ||
| 145-149 | LED Frequency 1200Hz (hold 3s) | ||
| 150-154 | LED Frequency 2000Hz (hold 3s) | ||
| 155-159 | LED Frequency 3600Hz (hold 3s) | ||
| 160-164 | LED Frequency 12KHz (hold 3s) | ||
| 165-169 | LED Frequency 25KHz (hold 3s) | ||
| 170-174 | No function | ||
| 175-179 | Fan Auto (hold 3s) | ||
| 180-184 | Fan Silent (hold 3s) | ||
| 185-189 | Fan Off (hold 3s) | ||
| 190-194 | Fan High Power (hold 3s) | ||
| 195-199 | No function | ||
| 200-214 | Invert Mapping Off (hold 3s) | ||
| 215-219 | Invert Mapping On (hold 3s) | ||
| 220-224 | No function | ||
| 225-229 | LED Mode – Illumination (hold 1,5s) | ||
| 230-234 | LED Mode – Boost (hold 1,5s) | ||
| 235-239 | No function | ||
| 240-244 | Factory Reset (hold 3s) | ||
| 245-249 | User Reset (hold 3s) | ||
| 250-255 | No function |
22CH STANDARD RGB
| CH | Function | Value | Setting |
| 1 | Master Dimmer | 000-255 | 0 – 100% |
| 2 | Master Dimmer Fine | 000-255 | 0-100% |
| 3 | Shutter | 0-19 | Shutter close |
| 20-24 | Shutter open | ||
| 25-64 | Strobe 1 (fast → slow) | ||
| 65-69 | Shutter open | ||
| 70-84 | Strobe 2: opening pulse (fast slow) | ||
| 85-89 | Shutter open | ||
| 90-104 | Strobe 3: closing pulse (fast slow) | ||
| 105-109 | Shutter open | ||
| 110-124 | Strobe 4: random strobe (fast slow) | ||
| 125-129 | Shutter open | ||
| 130-144 | Strobe 5: random opening pulse (fast slow) | ||
| 145-149 | Shutter open | ||
| 150-164 | Strobe 6: random closing pulse (fast slow) | ||
| 165-169 | Shutter open | ||
| 170-184 | Strobe 7: burst pulse (fast slow) | ||
| 185-189 | Shutter open | ||
| 190-204 | Strobe 8: random burst pulse (fast slow) | ||
| 205-209 | Shutter open | ||
| 210-224 | Strobe 9: sine wave (fast slow) | ||
| 225-229 | Shutter open | ||
| 230-244 | Strobe 10: burst (fast slow) | ||
| 245-255 | Shutter open | ||
| 4 | Dimmer 1 | 000-255 | 0-100% |
| 5 | Dimmer 1 Fine | 000-255 | 0-100% |
| 6 | Red 1 | 000 – 004 | 2900K |
| 7 | Red Fine1 | 000-255 | 0-100% |
| 8 | Green 1 | 000-255 | 0-100% |
| 9 | Green Fine1 | 000-255 | 0-100% |
| 10 | Blue1 | 000-255 | 0-100% |
| 11 | Blue Fine1 | 000-255 | 0-100% |
| 12 | Dimmer 2 | 000-255 | 0-100% |
| 13 | Dimmer Fine2 | 000-255 | 0-100% |
| 14 | Red 2 | 000-255 | 0-100% |
| 15 | Red Fine2 | 000-255 | 0-100% |
| 16 | Green 2 | 000-255 | 0-100% |
| 17 | Green Fine2 | 000-255 | 0-100% |
| 18 | Blue2 | 000-255 | 0-100% |
| 19 | Blue Fine2 | 000-255 | 0-100% |
| 20 | CTC (affects RGB 1+2) | 000-004 | 5600K |
| 005-182 | 2000K-6500K linear in 20-21K steps (please see detai- led CTC chart) | ||
| 182-182 | 5600K | ||
| 226-226 | 6500K | ||
| 227-255 | 6621K-10.000K linear in 120-121K steps (please see detailed CTC chart) | ||
| 21 | Tint (affects CTC and RGB 1+2) | 0 | no function |
| 000-127 | Magenta -> Neutral | ||
| 128-128 | Neutral | ||
| 129-255 | Neutral -> Green | ||
| 22 | Device S ettings (please see remark *1) | 000-029 | No function |
| 030-034 | Display Backlight On (hold 3s) | ||
| 035-039 | Display Backlight Off (hold 3s) | ||
| 040-044 | No function | ||
| 045-049 | DMX Fail Blackout (hold 3s) | ||
| 050-054 | DMX Fail Hold (hold 3s) | ||
| 055-059 | DMX Fail – Emergency Light (hold 3s) | ||
| 060-064 | No function | ||
| 065-069 | Linear Dimmer Curve (hold 1,5s) | ||
| 070-074 | Exponential Dimmer Curve (hold 1,5s) | ||
| 075-079 | Logarithmic Dimmer Curve (hold 1,5s) | ||
| 080-084 | S-Curve Dimmer Curve (hold 1,5s) | ||
| 085-089 | No function | ||
| 090-094 | LED (Fast) Dimmer Response (hold 1,5s) | ||
| 095-099 | Medium Dimmer Response (hold 1,5s) | ||
| 100-104 | Halogen (Slow) Dimmer Response (hold 1,5s) | ||
| 105-109 | No function | ||
| 110-114 | Redshift On (hold 1,5s / affects only between 2700- 3500K ) | ||
| 115-119 | Redshift Off (hold 1,5s) | ||
| 120-124 | No function | ||
| 125-129 | Full Calibration (Colors & CCT / hold 3s) | ||
| 130-134 | CCT Calibration (RAW Colors / hold 3s) | ||
| 135-139 | No function | ||
| 140-144 | LED Frequency 800Hz (hold 3s) | ||
| 145-149 | LED Frequency 1200Hz (hold 3s) | ||
| 150-154 | LED Frequency 2000Hz (hold 3s) | ||
| 155-159 | LED Frequency 3600Hz (hold 3s) | ||
| 160-164 | LED Frequency 12KHz (hold 3s) | ||
| 165-169 | LED Frequency 25KHz (hold 3s) | ||
| 170-174 | No function | ||
| 175-179 | Fan Auto (hold 3s) | ||
| 180-184 | Fan Silent (hold 3s) | ||
| 185-189 | Fan Off (hold 3s) | ||
| 190-194 | Fan High Power (hold 3s) | ||
| 195-199 | No function | ||
| 200-214 | Invert Mapping Off (hold 3s) | ||
| 215-219 | Invert Mapping On (hold 3s) | ||
| 220-224 | No function | ||
| 225-229 | LED Mode – Illumination (hold 1,5s) | ||
| 230-234 | LED Mode – Boost (hold 1,5s) | ||
| 235-239 | No function | ||
| 240-244 | Factory Reset (hold 3s) | ||
| 245-249 | User Reset (hold 3s) | ||
| 250-255 | No function |
24CH STANDARD RGB
|
CH |
Function | Value |
Setting |
| 1 | Master Dimmer | 000-255 | 0 – 100% |
| 2 | Shutter | 0-19 | Shutter close |
| 20-24 | Shutter open | ||
| 25-64 | Strobe 1 (fast → slow) | ||
| 65-69 | Shutter open | ||
| 70-84 | Strobe 2: opening pulse (fast slow) | ||
| 85-89 | Shutter open | ||
| 90-104 | Strobe 3: closing pulse (fast slow) | ||
| 105-109 | Shutter open | ||
| 110-124 | Strobe 4: random strobe (fast slow) | ||
| 125-129 | Shutter open | ||
| 130-144 | Strobe 5: random opening pulse (fast slow) | ||
| 145-149 | Shutter open | ||
| 150-164 | Strobe 6: random closing pulse (fast slow) | ||
| 165-169 | Shutter open | ||
| 170-184 | Strobe 7: burst pulse (fast slow) | ||
| 185-189 | Shutter open | ||
| 190-204 | Strobe 8: random burst pulse (fast slow) | ||
| 205-209 | Shutter open | ||
| 210-224 | Strobe 9: sine wave (fast slow) | ||
| 225-229 | Shutter open | ||
| 230-244 | Strobe 10: burst (fast slow) | ||
| 245-255 | Shutter open | ||
| 3 | Duration | 000-255 | 0 – 100% (0ms – 510ms) |
| 4 | Dimmer 1 | 000-255 | 0 – 100% |
| 5 | Red 1 | 000-255 | 0 – 100% |
| 6 | Green 1 | 000-255 | 0 – 100% |
| 7 | Blue 1 | 000-255 | 0 – 100% |
| 8 | CTC (affects RGB 1) | 000-004 | 5600K |
| 005-182 | 2000K-6500K linear in 20-21K steps (please see detailed CTC chart) | ||
| 182-182 | 5600K | ||
| 226-226 | 6500K | ||
| 227-255 | 6621K-10.000K linear in 120-121K steps (please see detailed CTC chart) | ||
| 9 | Tint (affects CTC and RGB 1) | 0 | no function |
| 000-127 | Magenta -> Neutral | ||
| 128-128 | Neutral | ||
| 129-255 | Neutral -> Green | ||
| 10 | Color Macro 1(overri- de RGB 1/ CTC 1) | Please see Pomelo color macro chart | |
| 11 | Color Macro Cross fade (Transition Time between Color Macros) | 000-005 | No function |
| 006-105 | 0,1s – 10s (0,1s steps) | ||
| 106-214 | 11s – 119s (1s steps) | ||
| 215-244 | 2m – 4m50s (10s steps) | ||
| 245-255 | 5m – 15m (1m steps) | ||
| 12 | Dimmer 2 | 000-255 | 0 – 100% |
| 13 | Red 2 | 000-255 | 0 – 100% |
| 14 | Green 2 | 000-255 | 0 – 100% |
| 15 | Blue 2 | 000-255 | 0 – 100% |
| 16 | CTC
(affects RGB 2) |
005-182 | 2000K-6500K linear in 20-21K steps (please see detailed CTC chart) |
| 182-182 | 5600K | ||
| 226-226 | 6500K | ||
| 227-255 | 6621K-10.000K linear in 120-121K steps (please see detailed CTC chart) | ||
| 17 | Tint (affects CTC and RGB 2) | 0 | no function |
| 000-127 | Magenta -> Neutral | ||
| 128-128 | Neutral | ||
| 129-255 | Neutral -> Green | ||
| 18 | Color Macro 1(ove- rride RGB 2/ CTC 2) | Please see Pomelo color macro chart | |
| 19 | Color Macro Cross fade (Transition Time between Color Macros) | 000-005 | No function |
| 006-105 | 0,1s – 10s (0,1s steps) | ||
| 106-214 | 11s – 119s (1s steps) | ||
| 215-244 | 2m – 4m50s (10s steps) | ||
| 245-255 | 5m – 15m (1m steps) | ||
| 20 | Effect override RGB 1+2 / CTC 1+2, Color Macro 1+2 | ||
| 000-015 | No Function | ||
| 016-039 | Effect 1 (slow to fast) | ||
| 040-063 | Effect 2 (slow to fast) | ||
| 064-087 | Effect 3 (slow to fast) | ||
| 088-111 | Effect 4 (slow to fast) | ||
| 112-135 | Effect 5 (slow to fast) | ||
| 136-159 | Effect 6 (slow to fast) | ||
| 160-183 | Effect 7 (slow to fast) | ||
| 184-207 | Effect 8 (slow to fast) | ||
| 208-231 | Effect 9 (slow to fast) ) | ||
| 232-55 | Effect 10 (slow to fast) | ||
| 21 | Dimmer Curve | 000-051 | No Function – Current Preset from Menu |
| Settings | |||
| 052-101 | Linear Dimmer Curve | ||
| 102-152 | Exponential Dimmer Curve | ||
| 153-203 | Logarithmic Dimmer Curve | ||
| 204-255 | S-Curve Dimmer Curve | ||
| 22 | Dimmer Response | 000-063 | No Function – Current Preset from Menu Settings |
| 064-127 | LED / fast | ||
| 128-191 | Medium | ||
| 192-255 | Halogen / slow | ||
| 23 | Redshift | 000-084 | No Function – Current Preset from Menu Settings |
| 085-170 | Redshift Off | ||
| 171-255 | Redshift On | ||
| 24 | Device Settings (please see remark *1) | 000-029 | No function |
| 030-034 | Display Backlight On (hold 3s) | ||
| 035-039 | Display Backlight Off (hold 3s) | ||
| 040-044 | No function | ||
| 045-049 | DMX Fail Blackout (hold 3s) | ||
| 050-054 | DMX Fail Hold (hold 3s) | ||
| 055-059 | DMX Fail – Emergency Light (hold 3s) | ||
| 060-064 | No function | ||
| 065-069 | Linear Dimmer Curve (hold 1,5s) | ||
| 070-074 | Exponential Dimmer Curve (hold 1,5s) | ||
| 075-079 | Logarithmic Dimmer Curve (hold 1,5s) | ||
| 080-084 | S-Curve Dimmer Curve (hold 1,5s) | ||
| 085-089 | No function | ||
| 090-094 | LED (Fast) Dimmer Response (hold 1,5s) | ||
| 095-099 | Medium Dimmer Response (hold 1,5s) | ||
| 100-104 | Halogen (Slow) Dimmer Response (hold 1,5s) | ||
| 105-109 | No function | ||
| 110-114 | Redshift On (hold 1,5s / affects only bet | ||
| ween 2700-3500K ) | |||
| 115-119 | Redshift Off (hold 1,5s) | ||
| 120-124 | No function | ||
| 125-129 | Full Calibration (Colors & CCT / hold 3s) | ||
| 130-134 | CCT Calibration (RAW Colors / hold 3s) | ||
| 135-139 | No function | ||
| 140-144 | LED Frequency 800Hz (hold 3s) | ||
| 145-149 | LED Frequency 1200Hz (hold 3s) | ||
| 150-154 | LED Frequency 2000Hz (hold 3s) | ||
| 155-159 | LED Frequency 3600Hz (hold 3s) | ||
| 160-164 | LED Frequency 12KHz (hold 3s) | ||
| 165-169 | LED Frequency 25KHz (hold 3s) | ||
| 170-174 | No function | ||
| 175-179 | Fan Auto (hold 3s) | ||
| 180-184 | Fan Silent (hold 3s) | ||
| 185-189 | Fan Off (hold 3s) | ||
| 190-194 | Fan High Power (hold 3s) | ||
| 195-199 | No function | ||
| 200-214 | Invert Mapping Off (hold 3s) | ||
| 215-219 | Invert Mapping On (hold 3s) | ||
| 220-224 | No function | ||
| 225-229 | LED Mode – Illumination (hold 1,5s) | ||
| 230-234 | LED Mode – Boost (hold 1,5s) | ||
| 235-239 | No function | ||
| 240-244 | Factory Reset (hold 3s) | ||
| 245-249 | User Reset (hold 3s) | ||
| 250-255 | No function | ||
33CH STANDARD RGB
| CH | Function | Value | Setting |
| 1 | Master Dimmer | 000-255 | 0 – 100% |
| 2 | MasterDimmerFine | 000-255 | 0 – 100% |
| 3 | Shutter | 0-19 | Shutter close |
| 20-24 | Shutter open | ||
| 25-64 | Strobe 1 (fast → slow) | ||
| 65-69 | Shutter open | ||
| 70-84 | Strobe 2: opening pulse (fast slow) | ||
| 85-89 | Shutter open | ||
| 90-104 | Strobe 3: closing pulse (fast slow) | ||
| 105-109 | Shutter open | ||
| 110-124 | Strobe 4: random strobe (fast slow) | ||
| 125-129 | Shutter open | ||
| 130-144 | Strobe 5: random opening pulse (fast slow) | ||
| 145-149 | Shutter open | ||
| 150-164 | Strobe 6: random closing pulse (fast slow) | ||
| 165-169 | Shutter open | ||
| 170-184 | Strobe 7: burst pulse (fast slow) | ||
| 185-189 | Shutter open | ||
| 190-204 | Strobe 8: random burst pulse (fast slow) | ||
| 205-209 | Shutter open | ||
| 210-224 | Strobe 9: sine wave (fast slow) | ||
| 225-229 | Shutter open | ||
| 230-244 | Strobe 10: burst (fast slow) | ||
| 245-255 | Shutter open | ||
| 4 | Duration | 000-255 | 0 – 100% (0ms – 510ms) |
| 5 | Dimmer 1 | 000-255 | 0-100% |
| 6 | Dimmer 1 Fine | 000-255 | 0-100% |
| 7 | Red 1 | 000-255 | 0-100% |
| 8 | Red Fine1 | 000-255 | 0-100% |
| 9 | Green 1 | 000-255 | 0-100% |
| 10 | Green Fine1 | 000-255 | 0-100% |
| 11 | Blue1 | 000-255 | 0-100% |
| 12 | Blue Fine1 | 000-255 | 0-100% |
| 13 | CTC 1 (affects RGB 1) | 000-004 | 5600K |
| 005-182 | 2000K-6500K linear in 20-21K steps (please see detailed CTC chart) | ||
| 182-182 | 5600K | ||
| 226-226 | 6500K | ||
| 227-255 | 6621K-10.000K linear in 120-121K steps (please see detailed CTC chart) | ||
| 14 | Tint1 (affects CTC and RGB 1) | 0 | no function |
| 000-127 | Magenta -> Neutral | ||
| 128-128 | Neutral | ||
| 129-255 | Neutral -> Green | ||
| 15 | Color Macro 1 (ove- rride RGB 1/ CTC 1) | Please see Pomelo color macro chart | |
| 16 | Color Macro Cross fade (Transition Time between Color Macros) | 000-005 | No function |
| 006-105 | 0,1s – 10s (0,1s steps) | ||
| 106-214 | 11s – 119s (1s steps) | ||
| 215-244 | 2m – 4m50s (10s steps) | ||
| 245-255 | 5m – 15m (1m steps) | ||
| 17 | Dimmer 2 | 000-255 | 0-100% |
| 18 | Dimmer 2 Fine | 000-255 | 0-100% |
| 19 | Red 2 | 000-255 | 0-100% |
| 20 | Red Fine2 | 000-255 | 0-100% |
| 21 | Green 2 | 000-255 | 0-100% |
| 22 | Green Fine2 | 000-255 | 0-100% |
| 23 | Blue2 | 000-255 | 0-100% |
| 24 | Blue Fine2 | 000-255 | 0-100% |
| 25 | CTC 2 (affects RGB 2) | 000-004 | 5600K |
| 005-182 | 2000K-6500K linear in 20-21K steps (please see detailed CTC chart) | ||
| 182-182 | 5600K | ||
| 226-226 | 6500K | ||
| 227-255 | 6621K-10.000K linear in 120-121K steps (please see detailed CTC chart) | ||
| 26 | Tint2 (affects CT- Cand RGB 2) | 0 | no function |
| 000-127 | Magenta -> Neutral | ||
| 128-128 | Neutral | ||
| 129-255 | Neutral -> Green | ||
| 27 | Color Macro 2 (override RGB 2/ CTC 1) | Please see Pomelo color macro chart | |
| 28 | Color Macro Cross fade (Transition Time between Color Macros) | 000-005 | No function |
| 006-105 | 0,1s – 10s (0,1s steps) | ||
| 106-214 | 11s – 119s (1s steps) | ||
| 215-244 | 2m – 4m50s (10s steps) | ||
| 245-255 | 5m – 15m (1m steps) | ||
| 29 | Effect override RGB 1+2 / CTC 1+2, Color Macro 1+2 | 000-015 | No Function |
| 016-039 | Effect 1 (slow to fast) | ||
| 040-063 | Effect 2 (slow to fast) | ||
| 064-087 | Effect 3 (slow to fast) | ||
| 088-111 | Effect 4 (slow to fast) | ||
| 112-135 | Effect 5 (slow to fast) | ||
| 136-159 | Effect 6 (slow to fast) | ||
| 160-183 | Effect 7 (slow to fast) | ||
| 184-207 | Effect 8 (slow to fast) | ||
| 208-231 | Effect 9 (slow to fast) ) | ||
| 232-55 | Effect 10 (slow to fast) | ||
| 30 | Dimmer Curve | 000-051 | No Function – Current Preset from Menu Settings |
| 052-101 | Linear Dimmer Curve | ||
| 102-152 | Exponential Dimmer Curve | ||
| 153-203 | Logarithmic Dimmer Curve | ||
| 204-255 | S-Curve Dimmer Curve | ||
| 31 | Dimmer Response | 000-063 | No Function – Current Preset from Menu Settings |
| 064-127 | LED / fast | ||
| 128-191 | Medium | ||
| 192-255 | Halogen / slow | ||
| 32 | Redshift | 000-084 | No Function – Current Preset from Menu Settings Redshift affects only between CCT 2700- 3500K. |
| 085-170 | Redshift Off | ||
| 171-255 | Redshift On | ||
| 33 | Device Settings | 000-029 | No function |
| 030-034 | Display Backlight On (hold 3s) | ||
| 035-039 | Display Backlight Off (hold 3s) | ||
| 040-044 | No function | ||
| 045-049 | DMX Fail Blackout (hold 3s) | ||
| 050-054 | DMX Fail Hold (hold 3s) | ||
| 055-059 | DMX Fail – Emergency Light (hold 3s) | ||
| 060-064 | No function | ||
| 065-069 | Linear Dimmer Curve (hold 1,5s) | ||
| 070-074 | Exponential Dimmer Curve (hold 1,5s) | ||
| 075-079 | Logarithmic Dimmer Curve (hold 1,5s) | ||
| 080-084 | S-Curve Dimmer Curve (hold 1,5s) | ||
| 085-089 | No function | ||
| 090-094 | LED (Fast) Dimmer Response (hold 1,5s) | ||
| 095-099 | Medium Dimmer Response (hold 1,5s) | ||
| 100-104 | Halogen (Slow) Dimmer Response (hold 1,5s) | ||
| 105-109 | No function | ||
| 110-114 | Redshift On (hold 1,5s / affects only bet ween 2700- 3500K ) | ||
| 115-119 | Redshift Off (hold 1,5s) | ||
| 120-124 | No function | ||
| 125-129 | Full Calibration (Colors & CCT / hold 3s) | ||
| 130-134 | CCT Calibration (RAW Colors / hold 3s) | ||
| 135-139 | No function | ||
| 140-144 | LED Frequency 800Hz (hold 3s) | ||
| 145-149 | LED Frequency 1200Hz (hold 3s) | ||
| 150-154 | LED Frequency 2000Hz (hold 3s) | ||
| 155-159 | LED Frequency 3600Hz (hold 3s) | ||
| 160-164 | LED Frequency 12KHz (hold 3s) | ||
| 165-169 | LED Frequency 25KHz (hold 3s) | ||
| 170-174 | No function | ||
| 175-179 | Fan Auto (hold 3s) | ||
| 180-184 | Fan Silent (hold 3s) | ||
| 185-189 | Fan Off (hold 3s) | ||
| 190-194 | Fan High Power (hold 3s) | ||
| 195-199 | No function | ||
| 200-214 | Invert Mapping Off (hold 3s) | ||
| 215-219 | Invert Mapping On (hold 3s) | ||
| 220-224 | No function | ||
| 225-229 | LED Mode – Illumination (hold 1,5s) | ||
| 230-234 | LED Mode – Boost (hold 1,5s) | ||
| 235-239 | No function | ||
| 240-244 | Factory Reset (hold 3s) Reset only starts if Shutter channel is set to DMX 250 | ||
| 245-249 | User Reset (hold 3s) Reset only starts if Shutter channel is set to DMX 250 / no self test by DMX | ||
| 250-255 | No function |
10CH DIRECT
| CH | Function | Value | Setting |
| 1 | Master Dimmer | 000-255 | 0 – 100% |
| 2 | Shutter | 0-19 | Shutter close |
| 20-24 | Shutter open | ||
| 25-64 | Strobe 1 (fast → slow) | ||
| 65-69 | Shutter open | ||
| 70-84 | Strobe 2: opening pulse (fast slow) | ||
| 85-89 | Shutter open | ||
| 90-104 | Strobe 3: closing pulse (fast slow) | ||
| 105-109 | Shutter open | ||
| 110-124 | Strobe 4: random strobe (fast slow) | ||
| 125-129 | Shutter open | ||
| 130-144 | Strobe 5: random opening pulse (fast slow) | ||
| 145-149 | Shutter open | ||
| 150-164 | Strobe 6: random closing pulse (fast slow) | ||
| 165-169 | Shutter open | ||
| 170-184 | Strobe 7: burst pulse (fast slow) | ||
| 185-189 | Shutter open | ||
| 190-204 | Strobe 8: random burst pulse (fast slow) | ||
| 205-209 | Shutter open | ||
| 210-224 | Strobe 9: sine wave (fast slow) | ||
| 225-229 | Shutter open | ||
| 230-244 | Strobe 10: burst (fast slow) | ||
| 245-255 | Shutter open | ||
| 3 | Red 1 | 000-255 | 0-100% |
| 4 | Green 1 | 000-255 | 0-100% |
| 5 | Blue1 | 000-255 | 0-100% |
| 6 | Amber 1 | 000-255 | 0-100% |
| 7 | White 1 | 000-255 | 0-100% |
| 8 | CTC (affects RGBAW) | 000-004 | 5600K |
| 005-182 | 2000K-6500K linear in 20-21K steps (plea- se see detailed CTC chart) | ||
| 182-182 | 5600K | ||
| 226-226 | 6500K | ||
| 227-255 | 6621K-10.000K linear in 120-121K steps (please see detailed CTC chart) | ||
| 9 | Tint (affects CTC and RGBAW ) | 0 | no function |
| 000-127 | Magenta -> Neutral | ||
| 128-128 | Neutral | ||
| 129-255 | Neutral -> Green | ||
| 10 | Color Macro (override RGB /CTC | Please see Pomelo color macro chart | |
| 11 | Color Macro Cross fade (Transition Time between- Color Macros) | 000-005 | No function |
| 006-105 | 0,1s – 10s (0,1s steps) | ||
| 106-214 | 11s – 119s (1s steps) | ||
| 215-244 | 2m – 4m50s (10s steps) | ||
| 245-255 | 5m – 15m (1m steps) | ||
| 12 | Device Settings (please see remark *1) | 000-029 | No function |
| 030-034 | Display Backlight On (hold 3s) | ||
| 035-039 | Display Backlight Off (hold 3s) | ||
| 040-044 | No function | ||
| 045-049 | DMX Fail Blackout (hold 3s) | ||
| 050-054 | DMX Fail Hold (hold 3s) | ||
| 055-059 | DMX Fail – Emergency Light (hold 3s) | ||
| 060-064 | No function | ||
| 065-069 | Linear Dimmer Curve (hold 1,5s) | ||
| 070-074 | Exponential Dimmer Curve (hold 1,5s) | ||
| 075-079 | Logarithmic Dimmer Curve (hold 1,5s) | ||
| 080-084 | S-Curve Dimmer Curve (hold 1,5s) | ||
| 085-089 | No function | ||
| 090-094 | LED (Fast) Dimmer Response (hold 1,5s) | ||
| 095-099 | Medium Dimmer Response (hold 1,5s) | ||
| 100-104 | Halogen (Slow) Dimmer Response (hold 1,5s) | ||
| 105-109 | No function | ||
| 110-114 | Redshift On (hold 1,5s / affects only bet | ||
| ween 2700-3500K ) | |||
| 115-119 | Redshift Off (hold 1,5s) | ||
| 120-124 | No function | ||
| 125-129 | Full Calibration (Colors & CCT / hold 3s) | ||
| 130-134 | CCT Calibration (RAW Colors / hold 3s) | ||
| 135-139 | No function | ||
| 140-144 | LED Frequency 800Hz (hold 3s) | ||
| 145-149 | LED Frequency 1200Hz (hold 3s) | ||
| 150-154 | LED Frequency 2000Hz (hold 3s) | ||
| 155-159 | LED Frequency 3600Hz (hold 3s) | ||
| 160-164 | LED Frequency 12KHz (hold 3s) | ||
| 165-169 | LED Frequency 25KHz (hold 3s) | ||
| 170-174 | No function | ||
| 175-179 | Fan Auto (hold 3s) | ||
| 180-184 | Fan Silent (hold 3s) | ||
| 185-189 | Fan Off (hold 3s) | ||
| 190-194 | Fan High Power (hold 3s) | ||
| 195-199 | No function | ||
| 200-214 | Invert Mapping Off (hold 3s) | ||
| 215-219 | Invert Mapping On (hold 3s) | ||
| 220-224 | No function | ||
| 225-229 | LED Mode – Illumination (hold 1,5s) | ||
| 230-234 | LED Mode – Boost (hold 1,5s) | ||
| 235-239 | No function | ||
| 240-244 | Factory Reset (hold 3s) Reset only starts if Shutter channel is set
to DMX 250 |
||
| 245-249 | User Reset (hold 3s) Reset only starts if Shutter channel is set to DMX 250 / no self test by DMX | ||
| 250-255 | No function |
17CH DIRECT
17Device Settings (please see remark *1)160-164
| CH | Function | Value | Setting |
| 1 | Master Dimmer | 000-255 | 0 – 100% |
| 2 | Shutter | 0-19 | Shutter close |
| 20-24 | Shutter open | ||
| 25-64 | Strobe 1 (fast → slow) | ||
| 65-69 | Shutter open | ||
| 70-84 | Strobe 2: opening pulse (fast slow) | ||
| 85-89 | Shutter open | ||
| 90-104 | Strobe 3: closing pulse (fast slow) | ||
| 105-109 | Shutter open | ||
| 110-124 | Strobe 4: random strobe (fast slow) | ||
| 125-129 | Shutter open | ||
| 130-144 | Strobe 5: random opening pulse (fast slow) | ||
| 145-149 | Shutter open | ||
| 150-164 | Strobe 6: random closing pulse (fast slow) | ||
| 165-169 | Shutter open | ||
| 170-184 | Strobe 7: burst pulse (fast slow) | ||
| 185-189 | Shutter open | ||
| 190-204 | Strobe 8: random burst pulse (fast slow) | ||
| 205-209 | Shutter open | ||
| 210-224 | Strobe 9: sine wave (fast slow) | ||
| 225-229 | Shutter open | ||
| 230-244 | Strobe 10: burst (fast slow) | ||
| 245-255 | Shutter open | ||
| 3 | Dimmer1 | 000-255 | 0 – 100% |
| 4 | Red 1 | 000-255 | 0-100% |
| 5 | Green 1 | 000-255 | 0-100% |
| 6 | Blue1 | 000-255 | 0-100% |
| 7 | Amber 1 | 000-255 | 0-100% |
| 8 | White 1 | 000-255 | 0-100% |
| 9 | Dimmer2 | 000-255 | 0-100% |
| 10 | Red 2 | 000-255 | 0-100% |
| 11 | Green 2 | 000-255 | 0-100% |
| 12 | Blue2 | 000-255 | 0-100% |
| 13 | Amber 2 | 000-255 | 0-100% |
| 14 | White 2 | 000-255 | 0-100% |
| 15 | CTC (affects RGBAW 1+2) | 000-004 | 5600K |
| 005-182 | 2000K-6500K linear in 20-21K steps (please see detai- led CTC chart) | ||
| 182-182 | 5600K | ||
| 226-226 | 6500K | ||
| 227-255 | 6621K-10.000K linear in 120-121K steps (please see detailed CTC chart) | ||
| 16 | Tint (affects CTC and RG- BAW1+2 ) | 0 | no function |
| 000-127 | Magenta -> Neutral | ||
| 128-128 | Neutral | ||
| 129-255 | Neutral -> Green | ||
| 17 | Device Settings (please see remark *1) | 000-029 | No function |
| 030-034 | Display Backlight On (hold 3s) | ||
| 035-039 | Display Backlight Off (hold 3s) | ||
| 040-044 | No function | ||
| 045-049 | DMX Fail Blackout (hold 3s) | ||
| 050-054 | DMX Fail Hold (hold 3s) | ||
| 055-059 | DMX Fail – Emergency Light (hold 3s) | ||
| 060-064 | No function | ||
| 065-069 | Linear Dimmer Curve (hold 1,5s) | ||
| 070-074 | Exponential Dimmer Curve (hold 1,5s) | ||
| 075-079 | Logarithmic Dimmer Curve (hold 1,5s) | ||
| 080-084 | S-Curve Dimmer Curve (hold 1,5s) | ||
| 085-089 | No function | ||
| 090-094 | LED (Fast) Dimmer Response (hold 1,5s) | ||
| 095-099 | Medium Dimmer Response (hold 1,5s) | ||
| 100-104 | Halogen (Slow) Dimmer Response (hold 1,5s) | ||
| 105-109 | No function | ||
| 110-114 | Redshift On (hold 1,5s / affects only between 2700- 3500K ) | ||
| 115-119 | Redshift Off (hold 1,5s) | ||
| 120-124 | No function | ||
| 125-129 | Full Calibration (Colors & CCT / hold 3s) | ||
| 130-134 | CCT Calibration (RAW Colors / hold 3s) | ||
| 135-139 | No function | ||
| 140-144 | LED Frequency 800Hz (hold 3s) | ||
| 145-149 | LED Frequency 1200Hz (hold 3s) | ||
| 150-154 | LED Frequency 2000Hz (hold 3s) | ||
| 155-159 | LED Frequency 3600Hz (hold 3s) | ||
| LED Frequency 12KHz (hold 3s) | |||
| 165-169 | LED Frequency 25KHz (hold 3s) | ||
| 170-174 | No function | ||
| 175-179 | Fan Auto (hold 3s) | ||
| 180-184 | Fan Silent (hold 3s) | ||
| 185-189 | Fan Off (hold 3s) | ||
| 190-194 | Fan High Power (hold 3s) | ||
| 195-199 | No function | ||
| 200-214 | Invert Mapping Off (hold 3s) | ||
| 215-219 | Invert Mapping On (hold 3s) | ||
| 220-224 | No function | ||
| 225-229 | LED Mode – Illumination (hold 1,5s) | ||
| 230-234 | LED Mode – Boost (hold 1,5s) | ||
| 235-239 | No function | ||
| 240-244 | Factory Reset (hold 3s) Reset only starts if Shutter channel is set to DMX 250 | ||
| 245-249 | User Reset (hold 3s) Reset only starts if Shutter channel is set to DMX 250 / no self test by DMX | ||
| 250-255 | No function |
28CH DIRECT
28Device Settings (please see remark *1)130-134
| CH | Function | Value | Setting |
| 1 | Master Dimmer | 000-255 | 0 – 100% |
| 2 | Shutter | 0-19 | Shutter close |
| 20-24 | Shutter open | ||
| 25-64 | Strobe 1 (fast → slow) | ||
| 65-69 | Shutter open | ||
| 70-84 | Strobe 2: opening pulse (fast slow) | ||
| 85-89 | Shutter open | ||
| 90-104 | Strobe 3: closing pulse (fast slow) | ||
| 105-109 | Shutter open | ||
| 110-124 | Strobe 4: random strobe (fast slow) | ||
| 125-129 | Shutter open | ||
| 130-144 | Strobe 5: random opening pulse (fast slow) | ||
| 145-149 | Shutter open | ||
| 150-164 | Strobe 6: random closing pulse (fast slow) | ||
| 165-169 | Shutter open | ||
| 170-184 | Strobe 7: burst pulse (fast slow) | ||
| 185-189 | Shutter open | ||
| 190-204 | Strobe 8: random burst pulse (fast slow) | ||
| 205-209 | Shutter open | ||
| 210-224 | Strobe 9: sine wave (fast slow) | ||
| 225-229 | Shutter open | ||
| 230-244 | Strobe 10: burst (fast slow) | ||
| 245-255 | Shutter open | ||
| 3 | Duration | 000-255 | 0 – 100% (0ms – 510ms) |
| 4 | Dimmer1 | 000-255 | 0 – 100% |
| 5 | Red 1 | 000-255 | 0-100% |
| 6 | Green 1 | 000-255 | 0-100% |
| 7 | Blue1 | 000-255 | 0-100% |
| 8 | Amber 1 | 000-255 | 0-100% |
| 9 | White 1 | 000-255 | 0-100% |
| 10 | CTC 1 (affects RGBAW 1) | 000-255 | 0-100% |
| 000-004 | 5600K | ||
| 005-182 | 2000K-6500K linear in 20-21K steps (please see detai- led CTC chart) | ||
| 182-182 | 5600K | ||
| 226-226 | 6500K | ||
| 227-255 | 6621K-10.000K linear in 120-121K steps (please see detailed CTC chart) | ||
| 11 | Tint 1(affects CTC1and RGBAW1 ) | 0 | no function |
| 000-127 | Magenta -> Neutral | ||
| 128-128 | Neutral | ||
| 129-255 | Neutral -> Green | ||
| 12 | Color Macro 1 (overrideR- GBAW1/CTC 1 ) | Please see Pomelo color macro chart | |
| 13 | Color Macro Cross Fade 1 (Transition Time between- Color Macros 1) | 000-005 | No function |
| 006-105 | 0,1s – 10s (0,1s steps) | ||
| 106-214 | 11s – 119s (1s steps) | ||
| 215-244 | 2m – 4m50s (10s steps) | ||
| 245-255 | 5m – 15m (1m steps) | ||
| 14 | Dimmer2 | 000-255 | 0 – 100% |
| 15 | Red 2 | 000-255 | 0-100% |
| 16 | Green 2 | 000-255 | 0-100% |
| 17 | Blue2 | 000-255 | 0-100% |
| 18 | Amber 2 | 000-255 | 0-100% |
| 19 | White 2 | 000-255 | 0-100% |
| 20 | CTC 2 (affects RGBAW 2) | 000-004 | 5600K |
| 005-182 | 2000K-6500K linear in 20-21K steps (please see detai- led CTC chart) | ||
| 182-182 | 5600K | ||
| 226-226 | 6500K | ||
| 227-255 | 6621K-10.000K linear in 120-121K steps (please see detailed CTC chart) | ||
| 21 | Tint 2(affects CTC2and RGBAW2 ) | 0 | no function |
| 000-127 | Magenta -> Neutral | ||
| 128-128 | Neutral | ||
| 129-255 | Neutral -> Green | ||
| 22 | Color Macro 2 (overrideR- GBAW2/ CTC 2 ) | Please see Pomelo color macro chart | |
| 23 | Color Macro Cross Fade 2 (Transition Time between- Color Macros 2) | 000-005 | No function |
| 006-105 | 0,1s – 10s (0,1s steps) | ||
| 106-214 | 11s – 119s (1s steps) | ||
| 215-244 | 2m – 4m50s (10s steps) | ||
| 245-255 | 5m – 15m (1m steps) | ||
| 25 | Dimmer Curve Settings | 000-051 | No Function – Current Preset from Menu |
| 052-101 | Linear Dimmer Curve | ||
| 102-152 | Exponential Dimmer Curve | ||
| 153-203 | Logarithmic Dimmer Curve | ||
| 204-255 | S-Curve Dimmer Curve | ||
| 26 | Dimmer Response Set- tings | 000-063 | No Function – Current Preset from Menu |
| 064-127 | LED / fast | ||
| 128-191 | Medium | ||
| 192-255 | Halogen / slow | ||
| 27 | Redshift Settings | 000-084 | No Function – Current Preset from Menu |
| 085-170 | Redshift Off | ||
| 171-255 | Redshift On | ||
| 28 | Device Settings (please see remark *1) | 000-029 | No function |
| 030-034 | Display Backlight On (hold 3s) | ||
| 035-039 | Display Backlight Off (hold 3s) | ||
| 040-044 | No function | ||
| 045-049 | DMX Fail Blackout (hold 3s) | ||
| 050-054 | DMX Fail Hold (hold 3s) | ||
| 055-059 | DMX Fail – Emergency Light (hold 3s) | ||
| 060-064 | No function | ||
| 065-069 | Linear Dimmer Curve (hold 1,5s) | ||
| 070-074 | Exponential Dimmer Curve (hold 1,5s) | ||
| 075-079 | Logarithmic Dimmer Curve (hold 1,5s) | ||
| 080-084 | S-Curve Dimmer Curve (hold 1,5s) | ||
| 085-089 | No function | ||
| 090-094 | LED (Fast) Dimmer Response (hold 1,5s) | ||
| 095-099 | Medium Dimmer Response (hold 1,5s) | ||
| 100-104 | Halogen (Slow) Dimmer Response (hold 1,5s) | ||
| 105-109 | No function | ||
| 110-114 | Redshift On (hold 1,5s / affects only bet | ||
| ween 2700-3500K
) |
|||
| 115-119 | Redshift Off (hold 1,5s) | ||
| 120-124 | No function | ||
| 125-129 | Full Calibration (Colors & CCT / hold 3s) | ||
| CCT Calibration (RAW Colors / hold 3s) | |||
| 135-139 | No function | ||
| 140-144 | LED Frequency 800Hz (hold 3s) | ||
| 145-149 | LED Frequency 1200Hz (hold 3s) | ||
| 150-154 | LED Frequency 2000Hz (hold 3s) | ||
| 155-159 | LED Frequency 3600Hz (hold 3s) | ||
| 160-164 | LED Frequency 12KHz (hold 3s) | ||
| 165-169 | LED Frequency 25KHz (hold 3s) | ||
| 170-174 | No function | ||
| 175-179 | Fan Auto (hold 3s) | ||
| 180-184 | Fan Silent (hold 3s) | ||
| 185-189 | Fan Off (hold 3s) | ||
| 190-194 | Fan High Power (hold 3s) | ||
| 195-199 | No function | ||
| 200-214 | Invert Mapping Off (hold 3s) | ||
| 215-219 | Invert Mapping On (hold 3s) | ||
| 220-224 | No function | ||
| 225-229 | LED Mode – Illumination (hold 1,5s) | ||
| 230-234 | LED Mode – Boost (hold 1,5s) | ||
| 235-239 | No function | ||
| 240-244 | Factory Reset (hold 3s) Reset only starts if Shutter channel is set to DMX 250 | ||
| 245-249 | User Reset (hold 3s) Reset only starts if Shutter channel is set to DMX 250 / no self test by DMX | ||
| 250-255 | No function |
41CH DIRECT
| CH | Function | Value | Setting |
| 1 | Master Dimmer | 000-255 | 0 – 100% |
| 2 | MasterDimmerFine | 000-255 | 0 – 100% |
| 3 | Duration | 0-19 | Shutter close |
| 20-24 | Shutter open | ||
| 25-64 | Strobe 1 (fast → slow) | ||
| 65-69 | Shutter open | ||
| 70-84 | Strobe 2: opening pulse (fast slow) | ||
| 85-89 | Shutter open | ||
| 90-104 | Strobe 3: closing pulse (fast slow) | ||
| 105-109 | Shutter open | ||
| 110-124 | Strobe 4: random strobe (fast slow) | ||
| 125-129 | Shutter open | ||
| 130-144 | Strobe 5: random opening pulse (fast slow) | ||
| 145-149 | Shutter open | ||
| 150-164 | Strobe 6: random closing pulse (fast slow) | ||
| 165-169 | Shutter open | ||
| 170-184 | Strobe 7: burst pulse (fast slow) | ||
| 185-189 | Shutter open | ||
| 190-204 | Strobe 8: random burst pulse (fast slow) | ||
| 205-209 | Shutter open | ||
| 210-224 | Strobe 9: sine wave (fast slow) | ||
| 225-229 | Shutter open | ||
| 230-244 | Strobe 10: burst (fast slow) | ||
| 245-255 | Shutter open | ||
| 4 | Duration | 000-255 | 0 – 100% (0ms – 510ms) |
| 5 | Dimmer 1 | 000-255 | 0-100% |
| 6 | Dimmer 1 Fine | 000-255 | 0-100% |
| 7 | Red 1 | 000-255 | 0-100% |
| 8 | Red Fine1 | 000-255 | 0-100% |
| 9 | Green 1 | 000-255 | 0-100% |
| 10 | Green Fine1 | 000-255 | 0-100% |
| 11 | Blue1 | 000-255 | 0-100% |
| 12 | Blue Fine1 | 000-255 | 0-100% |
| 13 | Amber 1 | 000-255 | 0-100% |
| 14 | Amber Fine 1 | 000-255 | 0-100% |
| 15 | White 1 | 000-255 | 0-100% |
| 16 | White Fine 1 | 000-255 | 0-100% |
| 17 | CTC 1 (affects RGBAW 1) (please see detailed CTC chart) | 000-004 | 5600K |
| 005-182 | 2000K-6500K linear in 20-21K steps | ||
| 182-182 | 5600K | ||
| 226-226 | 6500K | ||
| 227-255 | 6621K-10.000K linear in 120-121K steps (please see detailed CTC chart) | ||
| 18 | Tint 1(affects CTC1and RGBAW1 ) | 0 | no function |
| 000-127 | Magenta -> Neutral | ||
| 128-128 | Neutral | ||
| 129-255 | Neutral -> Green | ||
| 19 | Color Macro 1 (overrideR- GBAW1/ CTC 1 ) | Please see Pomelo color macro chart | |
| 20 | Color Macro Cross Fade 1 (Transition Time between- Color Macros 1) | 000-005 | No function |
| 006-105 | 0,1s – 10s (0,1s steps) | ||
| 106-214 | 11s – 119s (1s steps) | ||
| 215-244 | 2m – 4m50s (10s steps) | ||
| 245-255 | 5m – 15m (1m steps) | ||
| 21 | Dimmer 2 | 000-255 | 0-100% |
| 22 | Dimmer 2 Fine | 000-255 | 0-100% |
| 23 | Red 2 | 000-255 | 0-100% |
| 24 | Red Fine 2 | 000-255 | 0-100% |
| 25 | Green 2 | 000-255 | 0-100% |
| 26 | Green Fine 2 | 000-255 | 0-100% |
| 27 | Blue 2 | 000-255 | 0-100% |
| 28 | Blue Fine 2 | 000-255 | 0-100% |
| 29 | Amber 2 | 000-255 | 0-100% |
| 30 | Amber Fine 2 | 000-255 | 0-100% |
| 31 | White 2 | 000-255 | 0-100% |
| 32 | White Fine 2 | 000-255 | 0-100% |
| 33 | CTC 2 (affects RGBAW 2) | 000-004 | 5600K |
| 005-182 | 2000K-6500K linear in 20-21K steps (please see detai- led CTC chart) | ||
| 182-182 | 5600K | ||
| 226-226 | 6500K | ||
| 227-255 | 6621K-10.000K linear in 120-121K steps (please see detailed CTC chart) | ||
| 34 | Tint 2(affects CTC2 and RGBAW2 ) | 0 | no function |
| 000-127 | Magenta -> Neutral | ||
| 128-128 | Neutral | ||
| 129-255 | Neutral -> Green | ||
| 35 | Color Macro 2(overrideRG- BAW2/ CTC 2 ) | Please see Pomelo color macro chart | |
| 36 | Color Macro Cross Fade 2 (Transition Time between- Color Macros 2) | 000-005 | No function |
| 006-105 | 0,1s – 10s (0,1s steps) | ||
| 106-214 | 11s – 119s (1s steps) | ||
| 215-244 | 2m – 4m50s (10s steps) | ||
| 245-255 | 5m – 15m (1m steps) | ||
| 37 | Effect override RGB 1+2 / CTC 1+2, Color Macro 1+2 | 000-015 | No Function |
| 016-039 | Effect 1 (slow to fast) | ||
| 040-063 | Effect 2 (slow to fast) | ||
| 064-087 | Effect 3 (slow to fast) | ||
| 088-111 | Effect 4 (slow to fast) | ||
| 112-135 | Effect 5 (slow to fast) | ||
| 136-159 | Effect 6 (slow to fast) | ||
| 160-183 | Effect 7 (slow to fast) | ||
| 184-207 | Effect 8 (slow to fast) | ||
| 208-231 | Effect 9 (slow to fast) ) | ||
| 232-55 | Effect 10 (slow to fast) | ||
| 38 | Dimmer Curve | 000-051 | No Function – Current Preset from Menu Settings |
| 052-101 | Linear Dimmer Curve | ||
| 102-152 | Exponential Dimmer Curve | ||
| 153-203 | Logarithmic Dimmer Curve | ||
| 204-255 | S-Curve Dimmer Curve | ||
| 39 | Dimmer Response | 000-063 | No Function – Current Preset from Menu Settings |
| 064-127 | LED / fast | ||
| 128-191 | Medium | ||
| 192-255 | Halogen / slow | ||
| 40 | Redshift | 000-084 | No Function – Current Preset from Menu Settings |
| 085-170 | Redshift Off | ||
| 171-255 | Redshift On | ||
| 41 | Device Settings (please see remark *1) | 000-029 | No function |
| 030-034 | Display Backlight On (hold 3s) | ||
| 035-039 | Display Backlight Off (hold 3s) | ||
| 040-044 | No function | ||
| 045-049 | DMX Fail Blackout (hold 3s) | ||
| 050-054 | DMX Fail Hold (hold 3s) | ||
| 055-059 | DMX Fail – Emergency Light (hold 3s) | ||
| 060-064 | No function | ||
| 065-069 | Linear Dimmer Curve (hold 1,5s) | ||
| 070-074 | Exponential Dimmer Curve (hold 1,5s) | ||
| 075-079 | Logarithmic Dimmer Curve (hold 1,5s) | ||
| 080-084 | S-Curve Dimmer Curve (hold 1,5s) | ||
| 085-089 | No function | ||
| 090-094 | LED (Fast) Dimmer Response (hold 1,5s) | ||
| 095-099 | Medium Dimmer Response (hold 1,5s) | ||
| 100-104 | Halogen (Slow) Dimmer Response (hold 1,5s) | ||
| 105-109 | No function | ||
| 110-114 | Redshift On (hold 1,5s / affects only bet | ||
| ween 2700-3500K | |||
| 115-119 | Redshift Off (hold 1,5s) | ||
| 120-124 | No function | ||
| 125-129 | Full Calibration (Colors & CCT / hold 3s) | ||
| 130-134 | CCT Calibration (RAW Colors / hold 3s) | ||
| 135-139 | No function | ||
| 140-144 | LED Frequency 800Hz (hold 3s) | ||
| 145-149 | LED Frequency 1200Hz (hold 3s) | ||
| 150-154 | LED Frequency 2000Hz (hold 3s) | ||
| 155-159 | LED Frequency 3600Hz (hold 3s) | ||
| 160-164 | LED Frequency 12KHz (hold 3s) | ||
| 165-169 | LED Frequency 25KHz (hold 3s) | ||
| 170-174 | No function | ||
| 175-179 | Fan Auto (hold 3s) | ||
| 180-184 | Fan Silent (hold 3s) | ||
| 185-189 | Fan Off (hold 3s) | ||
| 190-194 | Fan High Power (hold 3s) | ||
| 195-199 | No function | ||
| 200-214 | Invert Mapping Off (hold 3s) | ||
| 215-219 | Invert Mapping On (hold 3s) | ||
| 220-224 | No function | ||
| 225-229 | LED Mode – Illumination (hold 1,5s) | ||
| 230-234 | LED Mode – Boost (hold 1,5s) | ||
| 235-239 | No function | ||
| 240-244 | Factory Reset (hold 3s) | ||
| 245-249 | User Reset (hold 3s) | ||
| 250-255 | No function |
Channel priority: Dimming>Built-in program call>User program call>ARGBW dimming>HSV dimming>Macro command>Color temperature
MAINTENANCE
In order to extend the service life of lamps, lamp maintenance is very necessary. The outdoor use environment is relatively harsh, or the lamps have been left for a long time.
The lens cover, lamp housing and other parts accumulate moisture and dust. At this time, the lamp needs to be cleaned to optimize the light output and to prevent dust and acid.
Gas causes corrosion to the casing.
The frequency of cleaning depends on the frequency of operation of the lamp and the surrounding environment. When cleaning, wipe carefully with a soft cloth and general glass cleaning products. It is recommended
Clean at least every 20 days.
Do not use organic solvents such as alcohol to wipe the lamp shell to avoid damage
GENERAL TROUBLESHOOTING
| Fault phenomenon | cause of issue | Approach |
| No menu displayed | 1. No AC power input 2. The switching power supply is dama- ged 3. Display board failure |
1.Check the power supply line 2.Check whether the switching power supply has voltage output 3.Replace the display board |
| Can’t receive DMX signal | 1. DMX signal line failure 2. The signal line wiring sequence is wrong. 3.The signal input terminal receiving signal IC is damaged. 4. DMX address code setting and conso- le The corresponding controls do not match 5. Other parameter settings are incorrect 6. Did not press the confirm key after entering the menu Or press the Esc key to exit to the main menu |
1.Check or replace signal cable 2.Check the wiring sequence of signal lines 3.Check the display board signal receiving IC and are the two resistors in series on the signal line open circuit. 4.Check or reset the address codeOr rest ore to factory settings and try again 5.Press Esc to exit to the main menu |
| The surface temperature of the lamp body exceeds 75° Temperature control protec- tion is not possible | 1. Thermistor failure on the LED lamp bead board 2. The temperature control circuit on the display board is faulty |
1.Replace the thermistor 2.Check the temperature control circuit on the motherboard |
| Uneven light mixing Uneven spots | 1. LED welding is incorrect 2. The lens or bracket is not installed properly |
1.Check the welding condition of LED lamp beads 2.Check the lens assembly process, Adjust the bracket assembly direction |
| The lamp does not light up or flickers a little | The LED is damaged or the driver board has no current output. | 1. Replace LED lamp beads 2.Replace damaged LEDs Or check the driver board circuit 3. Replace the corresponding driver IC |
| Parameters are not saved | The IC used to store parameters is da- maged | Replace storage IC |
| The whole lamp does not work when powered on | When the temperature is too high, the temperature control protection causes Switching power supply over-temperature protection does not work | Wait for the lamp body to cool down before tur- ning it on |
LAMP PARAMETERS
| Optical parameters | |
| light source | 2x 300W Red, Green, Blue, Amber, Warm-White |
| illumination | ALL: 26000Lux@1M ALL: 3400Lux@3M ALL: 1500Lux@5M |
| color temperature | WW2000K-10000K (±100K) |
| Optical system | Reflector with compound eye lens |
| color rendering index | Ra≥86 |
| dominant wavelength | R630nM/G529nM/B461nM/A115nM |
| Light source life | 50000 |
| Beam angle (50%) | 50° |
| Maximum field angle (10%) | 87° |
| pixel matrix | Point control/overall control |
| Strobe | 0/20Hz |
| Power parameters | |
| Input voltage and frequency | 100/240VAC , 50-60Hz |
| Power connection | Waterproof power cord input/output, maximum number of connections 6 units @230V |
| Signal connection | Three-core waterproof signal adapter cable input/output, maximum number of connections 32 units |
| constant power | 220W |
| Maximum power | 610W |
| Power Factor | 0.95/230V |
| working environment | -20-45 °C |
| Structural parameters | |
| SIZE | SIZE: 400*200*192.5mm |
| WEIGHT | NET WEIGHT: 8.9 kg |
| Protection level | IP65 |
| cooling system | Fan cooling |
| shell | Die-cast aluminum, black (customizable color) |
| Installation method | Flat ground, vertical hanging, side hanging |
| CONTROL | |
| control method | DMX512 / RDM |
| DMX CHANNEL | 1CH DWE, 2CH DWE, 4CH DWE, 9CH DWE+, 6CH STROBE, 6CH RGB, 10CH BASIC RGB, 14CH BASIC RGB, 13CH STAN- DARD RGB, 22CH STANDARD RGB, 24CH EXTENDED RGB, 33CH EXTENDED RGB, |
| 10CH DIRECT, 12CH DIRECT, 17CH DIRECT, 28CH DIRECT, 41CH DIRECT | |
| DISPLAY | OLED display with 4 touch buttons |
| Refresh frequency | 800Hz/1200Hz/2000Hz/3600Hz/12000Hz/25000Hz |
| Dimming delay | LED/Medium/Halogen |
| Dimming curve selection | Linear /Exponential/Logarithmic/S-Curve |
| Accessories | |
| Standard configuration | European standard waterproof power cord 1PCS; instruc- tion manual 1PCS |
DIMENSIONAL DRAWING
Documents / Resources
 |
Macaio Blinder Array FC [pdf] User Manual Blinder Array FC, Blinder, Array FC, FC |