CC1312PSIP SimpleLink Sub 1GHz Wireless System
“
Product Information:
Specifications:
- Compliance: Part 15 of FCC Rules
- Frequency: 15.247 GHz
- Installation: Professional installation required
- Intended Use: Industry/Commercial
- Radiation Exposure Limits: FCC compliant
- Minimum Distance: 20cm between radiator and body
Product Usage Instructions:
Installation:
The device requires professional installation due to its
intended use for industry/commercial purposes. The connector is
located within the transmitter enclosure and is not accessible to
the user without disassembling the transmitter. Installation must
be controlled and requires special training.
Regulatory Compliance:
Ensure compliance with FCC rules regarding harmful interference
and radiation exposure limits. Maintain a minimum distance of 20cm
between the transmitter and the body during installation and
operation. Do not co-locate with other antennas or
transmitters.
Module Integration:
If using multiple simultaneously transmitting conditions or
different operational setups, consult with the module manufacturer
for proper installation methods in the end system to ensure
compliance.
FAQ:
Q: What should I do if the FCC/ISED certification number is not
visible after installation?
A: If the certification number is not visible, ensure that the
exterior of the device displays a label referencing the enclosed
module with the appropriate identification number.
Q: Can the transmitter be operated in conjunction with other
antennas or transmitters?
A: No, the transmitter must not be co-located or operated with
any other antenna or transmitter to comply with FCC
regulations.
“`
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2.2 This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C DSS) .It is applicable to the modular transmitter
2.3 This radio transmitter 2AB2Q-1312PSIP has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. The concrete contents to check are the following three points. ) Maximum antenna gains are shown in item 2.7 below. ) Should be installed so that the end user cannot modify the antenna ) Feed line should be designed in 50ohm Fine-tuning of return loss etc. can be performed using a matching network. The antenna shall not be accessible for modification or change by the end user.
2.4 The module complies with FCC Part 15.247 and apply for Single module approval.
2.5 Trace antenna designs: applicable. The trace reference design information in the operational description is confidential. grantee will share the trace design to the OEM when sale out these modules. Any deviation(s) from the defined parameters of the antenna trace, as described by the instructions, require that the host product manufacturer must notify the module grantee that they wish to change the antenna trace design. In this case, a Class II permissive change application is required to be filed by the grantee, or the host manufacturer can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application.
PAGE 1 OF 8
Version 1.0
The device must be professionally installed. The intended use is generally not for the general public. It is generally for industry/commercial use. The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not normally required. The user has no access to the connector. Installation must be controlled. Installation requires special training.
2.6 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2.7
The following antennas have been certified for use with this module. Only antennas of the same type with equal or lower gain may also be used with this module. Other types of antennas and/or higher gain antennas may require the additional authorization for operation. The installer should use unique antenna connector and Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. The manufacturer of module will inform installer to meet with the FCC part 15.203 in the warning part. Antenna Specification list below:
2.8 Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as “Contains FCC ID: 2AB2Q-1312PSIP”; any similar wording that expresses the same meaning may be used.
2.9 Testing of the host product with all the transmitters installed referred to as the composite investigation test- is recommended, to verify that the host product meets all the applicable FCC rules. The radio spectrum is to be investigated with all the transmitters in the final host product functioning to determine that no emissions exceed the highest limit permitted for any one individual transmitter as required by Section 2.947(f). The host manufacturer is responsible to ensure that when their product operates as intended it does not have any emissions present that are out of compliance that were not present when the transmitters were tested individually.
If the modular transmitter has been fully tested by the module grantee on the required number of channels, modulation types, and modes, it should not be necessary for the host installer to re-test all the available transmitter modes or settings. It is recommended that the host product manufacturer, installing the modular transmitter, perform some investigative measurements to confirm that the resulting composite system does not exceed the spurious emissions limits or band edge limits (e.g., where a different antenna may be causing additional emissions). The testing should check for emissions that may occur due to the intermixing of emissions with the other transmitters, digital circuitry, or due to physical properties of the host product (enclosure). This investigation is especially important when integrating multiple modular transmitters where the certification is based on testing each of them in a stand-alone configuration.
PAGE 2 OF 8
Version 1.0
2.10 Any company of the host device which install this modular should perform the test of radiated & conducted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 & 15.207,15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and 15.209 & 15.207,15B class B requirement. Then the host can be sold legally. The host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
2.11 The host manufacture is recommended to use FCC KDB 996369 D04 Module Integration Guide recommending as “best practice” RF design engineering testing and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties.
2.12
This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.
Canada Statement
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 10256A-1312PSIP” any similar wording that expresses the same meaning may be used.
l’appareil hôte doit porter une étiquette donnant le numéro de certification du module d’Industrie Canada, précédé des mots « Contient un module d’émission », du mot « IC: 10256A-1312PSIP » ou d’une formulation similaire exprimant le même sens, comme suit
PAGE 3 OF 8
Version 1.0
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l’exemption des limites courantes d’évaluation dans la section 2.5 de RSS 102 etla conformité à l’exposition de RSS-102 RF, utilisateurs peut obtenir l’information canadienne surl’exposition et la conformité de rf.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu’aucune autre antenne ouémetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.
PAGE 4 OF 8
Version 1.0
This radio transmitter [IC: 10256A-1312PSIP] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. The concrete contents to check are the following three points. ) Maximum antenna gains are shown in following table. ) Should be installed so that the end user cannot modify the antenna; ) Feed line should be designed in 50ohm
Fine-tuning of return loss etc. can be performed using a matching network. Le présent émetteur radio [IC: 10256A-1312PSIP] a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d’antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l’exploitation de l’émetteur. Le contenu concret à vérifier sont les trois points suivants. ) Les gains maximaux d’antenne sont montrés dans le tableau suivant. ) doivent être installés de façon que l’utilisateur final ne peut pas modifier l’antenne ) La ligne d’alimentation doit être conçue en 50ohm
Le réglage précis de la perte de rendement, etc. peut être effectué en utilisant un réseau correspondant..
Antenna type and antenna gain:
PAGE 5 OF 8
Version 1.0
Notice to OEM integrator
Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual(FCC/Canada statement).
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host.
The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual.
Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID: 2AB2Q-1312PSIP or IC: 10256A-1312PSIP Both FCC ID and IC ID are not to be placed on the host at the same time and only hosts going into the US can use the FCC ID and only hosts going into Canada can use the IC ID.
l’hôte doit utiliser l’instrument uniquement dans des dispositifs qui répondent à la fcc / (catégorie d’exposition rf mobile, ce qui signifie le dispositif est installé et utilisé à une distance d’au moins 20 cm de personnes. le manuel de l’utilisateur final doit inclure la partie 15 / (fac rss gen déclarations de conformité relatives à l’émetteur que de montrer dans ce manuel. le fabricant est responsable de la conformité de l’hôte, le système d’accueil avec le module installé avec toutes les autres exigences applicables du système comme la partie 15 b, ices – 003. accueillir le fabricant est fortement recommandé de confirmer la conformité avec les exigences de la fcc / (émetteur lorsque le module est installé dans l’hôte. le dispositif d’accueil doivent avoir une étiquette indiquant contient FCC ID: 2AB2Q-1312PSIPIC: 10256A1312PSIP
Doit avoir sur l’appareil hôte une étiquette indiquant Contient l’ID FCC 2AB2Q-1312PSIP ou IC : 10256A1312PSIP L’ID FCC et l’ID IC ne doivent pas être placés sur l’hôte en même temps et seuls les hôtes se rendant aux États-Unis peuvent utiliser l’ID FCC et seuls les hôtes se rendant au Canada peuvent utiliser l’ID IC.
PAGE 6 OF 8
Version 1.0
Label:
PAGE 7 OF 8
Version 1.0
PAGE 8 OF 8
Version 1.0
Documents / Resources
 |
LEEDARSON CC1312PSIP SimpleLink Sub 1GHz Wireless System [pdf] Owner's Manual 1312PSIP, CC1312PSIP SimpleLink Sub 1GHz Wireless System, CC1312PSIP, SimpleLink Sub 1GHz Wireless System, Sub 1GHz Wireless System, Wireless System, System |