ICM-UFPT-2 & ICM-UFPT-5
Universal Function Programmable Timers
INSTALLATION, OPERATION & APPLICATION GUIDE
For more information on our complete range of American-made products – plus wiring diagrams, troubleshooting tips and more, visit us at www.icmcontrols.com
NEW UNIVERSAL CONTROLS VIA NFC TECHNOLOGY
PURPOSE OF CONTROL
- Universal function programmable timer using NFC technology
- Operating Control Time Switch
FEATURES
- Universal input voltage 24 -240VAC
- Reduce truck stock inventory
- Compatible with over 85 legacy ICM timers
- NFC technology allows for the user to change timer application on the fly using a smart phone to set up all functionality of the timerincluding mode and delay time.
- Installation instructions, wiring diagrams, and timing diagrams conveniently displayed on the App
- Easy installation
Uses near field communication in conjunction with a smart phone App to allow the user to select from six different timer modes - On delay
- Off delay (5-wire model only)
- Interval
- Anti-Short Cycle
- Repeat Cycle
- Single shot (5-wire model only)
SPECIFICATIONS
Electrical
- Impulse Voltage: 2500V
Input
- Voltage: 24-240 VAC
- Frequency: 50/60 Hz
Timing Modes
- Adjustable per app
Response Time
- 75 ms
NOTE: Any power lost during the first 0.5 to 3 seconds of operation will be ignored. (2-wire model only)
Action Type
- ICM-UFPT-2: Action Type 1.Q
- ICM-UFPT-5: Action Type 1.C.Q
Output
- ICM-UFPT-5:
– 1A@ 240VAC (pilot duty)
– 4FLA/4LRA@ 277VAC (AC motor)
– 5A@ 277VAC (general use)
– 8.75A@ 240VAC (resistive) - ICM-UFPT-2:
– 24-240VAC
– Maximum 0.5A
– Minimum 40mA
Dimensions
- 3” L X 2” W X 1” D
Environmental
- Pollution Degree: 2
WIRING DIAGRAMS
5-WIRE
CONSTRUCTION OF CONTROL
- Independently Mounted Control for Panel Mount
INSTALLATION AND MOUNTING
- Please use the provided wiring harness to wire the timer
- Install the control with a thread forming #10 sheet metal screw torqued to 14 in-lbs ± 2 in-lbs, through the center hole on the unit. The mounting surface is minimum 0.8 mm thick if steel, 1.2 mm thick if aluminum.
DIMENSIONS
Reading Your Device
From the Home Screen, tap on Read Device.
Read Device Program
Hold your phone near your ICM device. The checkmark shows complete.
USING THE NFC TECHNOLOGY
STEP 1 – Download the app Locate and download the “ICM Omni” app from the Google Play Store or Apple Store.
NEW UNIVERSAL CONTROLS VIA NFC TECHNOLOGY
STEP 2 –
Open the app and select Program Device
STEP 3 –
Select a Device to Program
STEP 4 –
Select a Program
Choose the option to create a new program or select asaved program.
STEPS 5 – 10
Select each Parameter and Program while following the app.
- On Delay
- Anti-Short Cycle
Delay – Optional On
Delay - Off Delay – Optional
On Delay - Repeat Cycle – Initial
State On, On Time,
Off Time, Optional
Start Delay - Interval – Duration
- Single Shot –
Duration
Examples:
Anti-Short
Cycle Delay –
2-wire
Repeat Cycle
– 5-wire
STEP 11 – Programming Your Device
Hold your phone near your ICM device.
The check mark shows complete.
7313 William Barry Blvd., North Syracuse, NY 13212
www.icmcontrols.com
800.365.5525
LIAF326
Documents / Resources
 |
ICM CONTROLS ICM-UFPT-2 Universal Function Programmable Timers [pdf] User Guide ICM-UFPT-2 Universal Function Programmable Timers, ICM-UFPT-2, Universal Function Programmable Timers, Function Programmable Timers, Programmable Timers |
 |
ICM CONTROLS ICM-UFPT-2 Universal Function Programmable Timer [pdf] User Guide ICM-UFPT-2 Universal Function Programmable Timer, ICM-UFPT-2, Universal Function Programmable Timer, Function Programmable Timer, Programmable Timer |
