750 Series Campus Access Points
“
Specifications
- Model: HPE Aruba Networking 750 Series Campus Access
Points - Package Contents: AP-754 or AP-755, Console Adapter Cable
(AP-755 only) - Hardware Features: Front, Side A, Side B, Rear View, LEDs,
Bluetooth Low Energy, Radio Console Port, Ethernet Ports,
Kensington Lock Slot, USB Interface, Reset Button - Default States: BLE Radio, Console Port, USB Host
Interface
Product Usage Instructions
Installation
- Identifying Specific Installation Locations:
Choose suitable locations for installing the access points ensuring
optimal coverage and connectivity. - Access Point Installation: Follow the
installation guide provided to securely mount the access points in
the chosen locations. - Software: Install the necessary software to
configure and manage the access points post-installation. - Verifying Post-Installation Connectivity:
Ensure proper connectivity by testing the access points after
installation.
Safety and Compliance
- Electrical: Adhere to electrical safety
guidelines while handling the equipment. - Environmental: Ensure the access points are
used within specified environmental conditions. - Regulatory Information: Familiarize yourself
with regulatory requirements related to the equipment. - Proper Disposal: Dispose of HPE Aruba
Networking equipment responsibly following guidelines.
FAQ
Q: Where can I find the latest software user guide?
A: The latest software user guide can be found at
here.
Q: How do I contact support for the HPE Aruba Networking 750
Series Campus Access Points?
A: You can contact support through the main site at https://www.arubanetworks.com
or the support site at https://networkingsupport.hpe.com.
For telephone support, refer to the provided numbers based on your
location.
“`
HPE Aruba Networking 750 Series Campus Access Points
Installation Guide
Copyright Information © Copyright 2024 Hewlett Packard Enterprise Development LP. Open Source Code This product includes code licensed under certain open source licenses which require source compliance. The corresponding source for these components is available upon request. This offer is valid to anyone in receipt of this information and shall expire three years following the date of the final distribution of this product version by Hewlett Packard Enterprise Company. To obtain such source code, please check if the code is available in the HPE Software Center at https://myenterpriselicense.hpe.com/cwp-ui/software but, if not, send a written request for specific software version and product for which you want the open source code. Along with the request, please send a check or money order in the amount of US $10.00 to: Hewlett Packard Enterprise Company Attn: General Counsel WW Corporate Headquarters 1701 E Mossy Oaks Rd Spring, TX 77389 United States of America.
HPE Aruba Networking 750 Series Campus Access Points | 2
Contents About This Guide
Guide Overview Related Documentation Contacting Support
Hardware Overview
Package Contents Front View External Antenna Connectors Side A View Side B View Rear View LEDs Bluetooth Low Energy and IEEE 802.15.4 Radio Console Port Ethernet Ports Kensington Lock Slot USB Interface Reset Button Power BLE Radio Default State Console Port Default State USB Host Interface Default State
Installation
Identifying Specific Installation Locations Access Point Installation Software Verifying Post-Installation Connectivity
Specifications, Safety and Compliance
Electrical Environmental Medical Regulatory Information Proper Disposal of HPE Aruba Networking Equipment
HPE Aruba Networking 750 Series Campus Access Points | Installation Guide
Contents
Contents
3 4
4 4 4
5
5 5 7 8 8 9 10 12 12 12 12 12 13 13 13 13 13
15
15 16 17 17
18
18 18 18 19 25
3
Chapter 1 About This Guide
About This Guide This document describes the hardware features of the HPE Aruba Networking 750 Series Campus Access Points. It provides a detailed overview of the physical and performance characteristics of each access point model and explains how to install the access point.
Guide Overview
n Hardware Overview provides hardware detail for the 750 Series. n Access Point Installation provides installation detail for the 750 Series. n Regulatory Information provides technical specifications, safety, regulatory and compliance information for the
750 Series.
Related Documentation
For complete management of an HPE Aruba Networking access point, the following documents are required:
n Latest Software User Guide: https://www.arubanetworks.com/techdocs/ArubaDocPortal/content/cons-aoshome.htm
n Command Line Interface (CLI) Bank: https://www.arubanetworks.com/techdocs/CLI-Bank/Content/Home.htm
Contacting Support
Table 1: Contact Information
Main Site
https://www.arubanetworks.com
Support Site
https://networkingsupport.hpe.com
Airheads Social Forums and Knowledge https://community.arubanetworks.com Base
North American Telephone
1-800-943-4526 (Toll Free) 1-408-754-1200
International Telephone
https://arubanetworks.com/support-services/contactsupport
Software Licensing Site
https://hpe.com/networking/support
End-of-life Information
https://www.arubanetworks.com/support-services/end-of-life
Security Incident Response Team
https://www.arubanetworks.com/support-services/securitybulletins
Email: sirt@arubanetworks.com
HPE Aruba Networking 750 Series Campus Access Points | Installation
4
Guide
Chapter 2 Hardware Overview
Hardware Overview
HPE Aruba Networking 750 Series Campus Access Points are high-performance, multi-radio wireless devices that can be deployed in either controller-based or controllerless network environments. These access points support the 802.11be standard in the 2.4 GHz, 5 GHz, and 6 GHz bands with a 4×4 MIMO tri-radio Wi-Fi 7 platform. Additionally, the 750 Series provides dual wired 10 Gbps Smart Rate Ethernet network interfaces that enhance performance and client capacity, enable (hitless) failover or capacity aggregation, and allow a combination of PoE power from two sources to deliver an increased power budget.
Package Contents
One of the following configurations:
Quantity 1
5
Item
HPE Aruba Networking 750 Series Campus Access Point (AP-754 or AP-755)
HPE Aruba Networking 750 Series Campus Access Point (AP755) and (1) Console Adapter Cable
n The AP mount bracket attaches to a variety of mounting kits (sold separately). n Inform your supplier if there are any incorrect, missing or damaged parts. If possible, retain the
carton, including the original packing materials which can be used to repack and return the unit to the supplier if needed.
Front View
HPE Aruba Networking 750 Series Campus Access Points | Installation
5
Guide
Figure 1 AP-755 Access Point Front View
Callout 1 2 3 4
Component System LED Radio LED (2.4GHz) Radio LED (5GHz) Radio LED (6GHz)
Figure 2 AP-754 Access Point Front View
HPE Aruba Networking 750 Series Campus Access Points | 6
Callout 1 2 3 4 5 6 7 8 9 10 11 12
Component External Antenna Connector A0 (2.4GHz and 5GHz, diplexed) External Antenna Connector A1 (2.4GHz and 5GHz, diplexed) External Antenna Connector A2 (2.4GHz and 5GHz, diplexed) External Antenna Connector A3 (2.4GHz and 5GHz, diplexed) External Antenna Connector B0 (6GHz) External Antenna Connector B1 (6GHz) External Antenna Connector B2 (6GHz) External Antenna Connector B3 (6GHz) System LED Radio LED (2.4GHz) Radio LED (5GHz) Radio LED (6GHz)
For more information on LED behavior, see LEDs.
External Antenna Connectors
AP-754 has two sets of four RP-SMA female connectors for external antennas: n First set (labeled as A0 through A3): 2.4 GHz and 5 GHz, combined (diplexed) n Second set (labeled as B0 through B3): 6 GHz
External antennas for this device must be installed by a professional installer, using manufacturerapproved antennas only. The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the regulatory limit set by the host country/domain. Installers are required to record the antenna gain for this device in the system management software. A list of approved antennas can be found in the ordering guide at https://www.hpe.com/psnow/doc/a00140934enw
Les antennes externes pour cet appareil doivent être installées par un professionnel agréé, en utilisant uniquement des antennes approuvées par le fabricant. Les niveaux équivalents de puissance à rayonnement isotrope (EIRP) pour tous les périphériques d’antenne externe ne doivent pas dépasser la limite réglementaire définie par le pays hôte / domaine. Les installateurs doivent enregistrer le gain d’antenne pour cet appareil dans le logiciel de gestion du système. Une liste d’antennes approuvées peut être trouvée à https://www.hpe.com/psnow/doc/a00140934enw
For the 6 GHz band, AP-754 is approved in the US (5925-6425 MHz and 6525-6875 MHz) and Canada (5925-6875 MHz) for Standard Power operations (in conjunction with an Automated Frequency Coordination [AFC] system).
HPE Aruba Networking 750 Series Campus Access Points | Installation Guide
7
Side A View
Figure 3 AP-755 Access Point Side A View
Callout 1 2
Component USB Host Port
Figure 4 AP-754 Access Point Side A View
Callout 1 2
Component USB Host Port
Side B View
Figure 5 AP-755 Access Point Side B View
HPE Aruba Networking 750 Series Campus Access Points | 8
Callout 1 2 3
Component E0 Ethernet Port E1 Ethernet Port
Figure 6 AP-754 Access Point Side B View
Callout 1 2 3
Component E0 Ethernet Port E1 Ethernet Port
Rear View
Figure 7 AP-755 Access Point Rear View
HPE Aruba Networking 750 Series Campus Access Points | Installation Guide
9
Callout 1 2 3 4
Component Console Port Reset Button DC Power Interface
Figure 8 AP-754 Access Point Rear View
Callout 1 2 3 4
Component Console Port Reset Button DC Power Interface
LEDs
The LED indicators located on the front cover of the access point indicate the system status of the access point.
System Status LED
Table 2: System Status LED Color/State
Off
Device Powered off
Meaning
HPE Aruba Networking 750 Series Campus Access Points | 10
Color/State Green- solid 1 Green- blinking 1 Green- flashing off 2 Green- flashing on 3 Amber- solid Amber- flashing off 2 Red
Meaning
Device ready, fully functional, no network restrictions
Device booting, not ready
Device ready, fully functional, either uplink negotiated in sub-optimal speed (< 1 Gbps)
Device in deep-sleep mode
Device ready, restricted power mode (limited PoE power available, or IPM restrictions applied), no network restrictions
Device ready, restricted power mode (limited PoE power available, or IPM restrictions applied), uplink negotiated in sub-optimal speed (< 1 Gbps)
System error condition (insufficient PoE power source [802.3af] in use) – Immediate attention required
1. Blinking: one second on, one second off, 2 seconds cycle. 2. Flashing off: mostly on, fraction of a second off, 2 seconds cycle. 3. Flashing on: mostly off, fraction of a second on, 2 seconds cycle.
Radio Status LEDs
The Radio Status LED table below is applicable to 2GHz, 5GHz, and 6GHz indicators, for each corresponding radio.
Table 3: Radio Status LED Color/State
Meaning
Off
Device powered off, or radio disabled
Green- solid
Radio enabled in access (AP) mode
Green- flashing off 1
Radio enabled in uplink or mesh mode
Amber- solid
Radio enabled in monitor or spectrum analysis mode
1. Flashing off: mostly on, fraction of a second off, 2 seconds cycle.
LED Display Settings
The LEDs have three operating modes that can be selected in the system management software: n Default mode: refer to Table 2 and Table 3. n Off mode: all LEDs are off n Blink mode: all LEDs blink green (synchronized) To force the LEDs into off mode or back to software defined mode, press the reset button for a short duration (less than 10 seconds).
HPE Aruba Networking 750 Series Campus Access Points | Installation Guide
11
Pressing the reset button for longer than 10 seconds may cause the AP to reset and return to factory default state.
Bluetooth Low Energy and IEEE 802.15.4 Radio
750 Series access points are equipped with an integrated BLE 5.0 and IEEE 802.15.4 (Zigbee) radio that provide the following capabilities: n location and asset-tracking applications n wireless console access n IoT gateway applications
Console Port
The console port is a Micro-B connector is located on the back of this device. Use the proprietary AP-CBL-SERU cable or AP-MOD-SERU module (sold separately) for direct management of this device when connected to a serial terminal or laptop. For pin-out details, refer to Figure 9. Figure 9 Micro-B Port Pin-out
1: NC 2: RXD 3: TXD 4: GND 5: GND
Ethernet Ports
The 750 Series access points are equipped with two active Ethernet ports (E0 and E1). Both ports are 100/1000/2500/5000 Base-T, auto-sensing MDI/MDIX, which supports uplink connectivity when linked by an Ethernet cable. Refer to Figure 10 for a detailed port pin-out. Figure 10 100/1000/2500/5000 Base-T
Kensington Lock Slot
750 Series access points are equipped with a Kensington lock slot for additional physical security.
USB Interface
HPE Aruba Networking 750 Series Campus Access Points | 12
The USB 2.0 interface located on the side of a 750 Series AP (see Side A View) is compatible with select cellular modems and other peripherals. When active, this port can supply up to 5W/1A to a connected device.
Reset Button
The reset button located on the bottom of the device can be used to reset the access point to factory default settings or turn off/on the LED display. Use one of the following methods to reset the access point to factory default settings: To reset during normal operation:
1. Hold the reset button for more than 10 seconds while the access point is running. 2. Release the reset button.
To reset during power up, hold the reset button while the access point is powering up.
The system status LED will flash again within 15 seconds indicating that the reset is completed. The access point will now continue to boot with the factory default settings. To toggle the LED display between Off and Blinking, during the normal operation of the access point, shortly press and release the reset button using a small, narrow object, such as a paperclip.
Power
Both Ethernet ports support PoE-in, allowing the AP to draw power from an 802.3at/802.3bt PoE power source. When the AP is powered by both E0 and E1 ports simultaneously, the AP can be configured by management software to source PoE power from either port. To combine power from both ports an 802.3af source can be used.
PoE input rating is 57V max | 3.0A is per pair of wires in Ethernet cable. Ethernet cable has 4 pair of wires in total.
If PoE is not available, a proprietary 12V DC power adapter (sold separately) can be used to power the access point. When both PoE and DC power sources are available, the DC power source takes precedence. In that case, the access point simultaneously draws a minimal current from the PoE source. In the event that the DC source fails, the access point switches to the PoE source.
BLE Radio Default State
The integrated BLE radio is enabled by default when Access Points with a non TAA/FIPS product SKU are in the factory default state. TAA/FIPS compliant Access Points in the factory default state will have the integrated BLE radio disabled. Once the AP has established a connection with its management platform, the BLE radio state is updated to match what’s configured there. This state is maintained if the AP is power-cycled or rebooted.
Console Port Default State
When the Access Point is in factory default state the console interface (both physical port and BLE) is enabled with default credentials (username is “admin” and password is the serial number of the unit). The console port state (enabled/disabled) and access credentials are updated to match what is configured in the management platform after the AP has established a connection and synchronized with the management platform. State and credentials are maintained if the AP is power-cycled or rebooted.
USB Host Interface Default State
When the Access Point is in factory default state the USB host interface is powered and enabled, assuming the AP is not in a restricted power mode. On some AP models the USB port may be disabled when a PoE source with
HPE Aruba Networking 750 Series Campus Access Points | Installation Guide
13
insufficient power budget is used. The USB host interface state is updated to match what is configured in the management platform after the AP has established a connection and synchronized with the management platform. This state is maintained if the AP is power-cycled or rebooted.
HPE Aruba Networking 750 Series Campus Access Points | 14
Chapter 3 Installation
Installation Refer to the sections below before beginning the installation process.
FCC Statement: Improper termination of access points installed in the United States configured to non-US model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).
Pre-Installation Checklist
Before installing your 750 Series access point, ensure that you have the following:
For Mounts, Antennas, Power and other Accessories, see the AP Accessories Guide.
n A mount kit compatible with the AP and mount surface n One or two Cat5E or better UTP cables with network access n Compatible antenna(s) and optional mount kit(s) when installing AP-754 n Optional items:
o A compatible power adapter with cord o A compatible PoE midspan injector with power cord o An AP-CBL-SERU console cable o An AP-MOD-SERU console module n Also, make sure at least one of the following network services is supported: o HPE Aruba Networking Discovery Protocol (ADP) o DNS server with an “A” record o DHCP Server with vendor specific options
n HPE Aruba Networking in compliance with governmental requirements, has designed the HPE Aruba Networking 750 Series access points so that only authorized network administrators can change configuration settings. For more information about AP configuration, refer to the AP Software Quick Start Guide.
n If a power adapter other than an approved adapter is used in the US or Canada, it should be NRTL listed, with an output rated 12V DC, minimum 4A, marked “LPS” and “Class 2,” and suitable for plugging into a standard power receptacle in the US and Canada
Identifying Specific Installation Locations
Use the access point placement map generated by HPE Aruba Networking 750 Series RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF
HPE Aruba Networking 750 Series Campus Access Points | Installation
15
Guide
absorbers/reflectors/interference sources will impact RF propagation and should be accounted for during the planning phase and adjusted for in RF plan.
Identifying Known RF Absorbers/Reflectors/Interference Sources
Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach an access point to its fixed location. RF absorbers include: n Cement/concrete–Old concrete has high levels of water dissipation, which dries out the concrete, allowing for
potential RF propagation. New concrete has high levels of water concentration in the concrete, blocking RF signals. n Natural Items–Fish tanks, water fountains, ponds, and trees n Brick RF reflectors include: n Metal Objects–Metal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh windows, blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets. n Do not place an access point between two air conditioning/heating ducts. Make sure that access points are placed below ducts to avoid RF disturbances. n RF interference sources include: n Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones) n Cordless headset such as those used in call centers or lunch rooms
Portable RF communications equipment should be used no closer than 30 cm (12 inches) to any part of the access point. Otherwise, degradation of the performance of this equipment could result.
Access Point Installation
For indoor use only. The access point, AC adapter, and all connected cables are not to be installed outdoors. This stationary device is intended for stationary use in partly temperature controlled weather-protected environments (class 3.2 per ETSI 300 019).
n All access points should be professionally installed by a Certified Mobility Professional (ACMP). The installer is responsible for ensuring that grounding is available and meets applicable national and electrical codes. Failure to properly install this product may result in physical injury and/or damage to property.
n Tous les points d’accès doivent impérativement être installés par un professionnel agréé. Ce dernier doit s’assurer que l’appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques nationaux en vigueur. Le fait de ne pas installer correctement ce produit peut entraîner des blessures corporelles et / ou des dommages matériels.
HPE Aruba Networking 750 Series Campus Access Points | 16
Software
For instructions on choosing operating modes and initial software configuration, refer to the AP Software Quick Start Guide.
Minimum Operating System Software Versions
n AP-754 (Excluding 6 GHz support): o ArubaOS and Aruba InstantOS (10.7.1.0 or later) o ArubaOS (10.7.1.0 or later)
n AP-754 (Including 6 GHz support): o ArubaOS and Aruba InstantOS (10.7.1.0 or later) o ArubaOS (10.7.1.0 or later)
n AP-755: o ArubaOS and Aruba InstantOS (10.7.1.0 or later) o ArubaOS (10.7.1.0 or later)
HPE Aruba Networking access points are classified as radio transmission devices, and are subject to government regulations of the host country. The network administrator(s) is/are responsible for ensuring that configuration and operation of this equipment is in compliance with their country’s regulations. For a complete list of approved channels in your country, refer to the HPE Aruba Networking Downloadable Regulatory Table at https://www.arubanetworks.com/techdocs/DRT/Default.htm.
Verifying Post-Installation Connectivity
The integrated LEDs on the access point can be used to verify that the access point is receiving power and initializing successfully (see Table 1 and Table 2). Refer to the AP Software Quick Start Guide for further details on verifying post-installation network connectivity.
HPE Aruba Networking 750 Series Campus Access Points | Installation Guide
17
Chapter 4 Specifications, Safety and Compliance
Specifications, Safety and Compliance
Electrical
Ethernet n E0: 100/1000/2500/5000 Base-T auto-sensing Ethernet RJ-45 Interfaces n E1: 100/1000/2500/5000 Base-T auto-sensing Ethernet RJ-45 Interfaces Power n Power over Ethernet (IEEE 802.3at and 802.3bt compliant) n 12V DC power interface, support powering through AC-to-DC power adapter n Maximum power consumption: Refer to datasheet
Environmental
Operating n Temperature: 0°C to +50°C (+32°F to +122°F) n Humidity: 5% to 95% non-condensing Storage n Temperature: -40ºC to 70ºC (-40ºF to 158ºF) n Humidity: 5% to 95% non-condensing
Medical
Equipment not suitable for use in the presence of flammable mixtures. Connect to only IEC 62368-1 or IEC 60601-1 certified products and power sources. The end user is responsible for the resulting medical system complies with the requirements of IEC 60601-1. Wipe with a dry cloth, no additional maintenance required. No serviceable parts, the unit must be sent back to the manufacturer for repair. No modifications are allowed without approval from HPE Aruba Networking.
HPE Aruba Networking 750 Series Campus Access Points | Installation
18
Guide
n Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in improper operation. If such use is necessary, this equipment and the other equipment should be observed to verify that they are operating normally.
n Use of accessories, transducers and cables other than those specified or provided by the manufacturer of this equipment could result in increased electromagnetic emissions or decreased electromagnetic immunity of this equipment and result in improper operation.
n Portable RF communications equipment (including peripherals such as antenna cables and external antennas) should be used no closer than 30 cm (12 inches) to any part of the access point. Otherwise, degradation of the performance of this equipment could result.
Regulatory Information
For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number (RMN). The regulatory model number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this regulatory model number. The regulatory model number RMN is not the marketing name or model number of the product. The following regulatory model numbers apply to the 750 Series:
n AP-754 RMN: APIN0754 n AP-755 RMN: APIN0755
Regulatory consideration for AP-754: AP-754 will be offered in countries where there is an existing or clear and defined path to allow operation of 6GHz radios with external connectorized antennas, either as a Low Power Indoor (LPI) or Standard Power (SPI) product. Please contact your HPE Aruba Networking representative to confirm (existing or planned) availability for the country where the AP will be deployed.
Brazil
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados. O uso deste equipamento é restrito a ambientes fechados e proibido em plataformas petrolíferas, carros, trens, embarcações e no interior de aeronaves abaixo de 3.048 m (10.000 pés). Para mais informações, consulte o site da Anatel: https://www.gov.br/anatel/pt-br
Canada
Innovation, Science and Economic Development
This Class B digital apparatus meets all of the requirements of the Canadian Interference-Causing Equipment Regulations. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
HPE Aruba Networking 750 Series Campus Access Points | 19
When operated in 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems.
This radio transmitter 4675A-APIN0754 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Antenna AP-ANT-311 AP-ANT-312 AP-ANT-313 AP-ANT-340 AP-ANT-345 AP-ANT-348
Gain (2.4/5/6GHz) 3.0/6.0/6.0 3.3/3.3/4.1 3.0/6.0/6.0 4.0/5.0/5.0 6.1/6.1/5.4 7.5/8.0/8.0
Impeadance 50ohm 50ohm 50ohm 50ohm 50ohm 50ohm
n Operation shall be limited to indoor use only. n Operation on oil platforms, cars, trains, boats, and aircraft shall be prohibited except for on large
aircraft flying above 10,000 feet. n Devices shall not be used for control of or communications with unmanned aircraft systems.
Innovation, Sciences et Développement économique
Cet appareil numérique de classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Cet appareil contient des émetteurs / récepteurs exemptés de licence qui sont conformes aux RSS exempts de licence d’Innovation, Sciences et Développement économique Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) ce périphérique ne doit pas provoquer d’interférences, et (2) ce périphérique doit accepter toute interférence, y compris les interférences susceptibles de provoquer un dysfonctionnement.
En cas d’utilisation dans la plage de fréquences de 5,15 à 5,25 GHz, cet appareil doit uniquement être utilisé à intérieur afin de réduire les risques d’interférence avec les systèmes satellites mobiles partageant le même canal.
Cet émetteur radio 4675A-APIN0754 a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d’antennes répertoriés ci-dessous, avec le gain maximum autorisé indiqué. Les types d’antennes non inclus dans cette liste qui ont un gain supérieur au gain maximum indiqué pour tout type répertorié sont strictement interdits pour une utilisation avec cet appareil.
Antenne Gagner (2.4/5/6GHz)
AP-ANT-311
3.0/6.0/6.0
AP-ANT-312
3.3/3.3/4.1
Impédance 50ohm 50ohm
HPE Aruba Networking 750 Series Campus Access Points | Installation Guide
20
Antenne Gagner (2.4/5/6GHz)
AP-ANT-313
3.0/6.0/6.0
AP-ANT-340 AP-ANT-345 AP-ANT-348
4.0/5.0/5.0 6.1/6.1/5.4 7.5/8.0/8.0
Impédance 50ohm 50ohm 50ohm 50ohm
n Le fonctionnement est restreint à une utilisation à l’intérieur seulement.
n L’utilisation sur les plateformes pétrolières ou dans les voitures, les trains, les bateaux et les avions est interdite, à l’exception des gros avions volant à plus de 3 km (10 000 pi).
n Cet appareil ne doit pas être utilisé pour le contrôle ou pour la communication avec des systèmes de drones.
European Union and United Kingdom
The Declaration of Conformity made under Radio Equipment Directive 2014/53/EU as well as the United Kingdom’s Radio Equipment Regulations 2017/UK is available for viewing below.. Select the document that corresponds to your device’s model number as it is indicated on the product label. EU & UK Declaration of Conformity Compliance is only assured if the HPE Aruba Networking approved accessories as listed in the ordering guide are used. This device is limited for indoor use. Use in trains with metal-coated windows (or similar structures made of materials with comparable attenuation characteristic) and aircraft is permitted. Operations in the 6GHz band are blocked by firmware for some countries pending adoption of spectrum. Refer to HPE Aruba Networking DRT release notes for details.
Wireless Channel Restrictions
5150-5350MHz band is limited to indoor only in the following countries; Austria (AT), Belgium (BE), Bulgaria (BG), Croatia (HR), Cyprus (CY), Czech Republic (CZ), Denmark (DK), Estonia (EE), Finland (FI), France (FR), Germany (DE), Greece (GR), Hungary (HU), Iceland (IS), Ireland (IE), Italy (IT), Latvia (LV), Liechtenstein (LI), Lithuania (LT), Luxembourg (LU), Malta (MT), Netherlands (NL), Norway (NO), Poland (PL), Portugal (PT), Romania (RO), Serbia (RS), Slovakia (SK), Slovenia (SL), Spain (ES), Sweden (SE), Switzerland (CH), Turkey (TR), United Kingdom (UK (NI).
Radio BLE/Zigbee
Frequency Range 2402-2480 MHz
Max EIRP 10 dBm
HPE Aruba Networking 750 Series Campus Access Points | 21
Radio Wi-Fi
Frequency Range 2412-2472 MHz 5150-5250 MHz 5250-5350 MHz 5470-5725 MHz 5752-5850 MHz 5945-6245 MHz
Max EIRP 20 dBm 23 dBm 23 dBm 30 dBm 14 dBm 23dBm
Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide/Instant User Guide for details on restrictions.
India
This product conforms to the relevant Essential Requirements of TEC, Department of Telecommunications, Ministry of Communications, Govt of India, New Delhi-110001.
Japan
México
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debeaceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.
EAC
h
HPE Aruba Networking 750 Series Campus Access Points | Installation Guide
22
TOO «- ()», , 050040, . , , -, 77/7, /: + 7 727 355 35 50 «- ()», , 050040, ., , , 77/7, /: +7 727 355 35 50
Taiwan
n
n
n n n MPE 1 mW/cm2 0.26 mW/cm2 20
n (Applicant): n (Address):11568 66 10 1 n (TEL): (02) 2652-8700
Thailand
Ukraine
Hereby, Hewlett Packard Enterprise Company declares that the radio equipment type [The Regulatory Model Number [RMN] for this device can be found in the Regulatory Information section of this document] is in compliance with Ukrainian Technical Regulation on Radio Equipment, approved by resolution of the CABINET OF MINISTERS OF UKRAINE dated May 24, 2017, No. 355. The full text of the UA declaration of conformity is available at the following internet address: https://certificates.ext.hpe.com/public/certificates.html.
HPE Aruba Networking 750 Series Campus Access Points | 23
‘ , 6280 -, -, 95002,
United States
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
n Reorient or relocate the receiving antenna. n Increase the separation between the equipment and receiver. n Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. n Consult the dealer or an experienced radio or TV technician for help.
Improper termination of access points installed in the United States configured to a non-US model controller is a violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80). This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
The network administrator(s) is/are responsible for ensuring that this device operates in accordance with local/regional laws of the host domain.
HPE Aruba Networking 750 Series Campus Access Points | Installation Guide
24
n FCC regulations restrict the operation of this device to indoor use only. n The operation of this device is prohibited on oil platforms, cars, trains, boats, and
aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet only in the 5.925-6.425GHz band. n Operation in the 5.9725-7.125 GHz band is prohibited for control of or communication with unnamed aircraft systems. n Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. n Toute modification effectuée sur cet équipement sans l’autorisation expresse de la partie responsable de la conformité est susceptible d’annuler son droit d’utilisation. n RF Radiation Exposure Statement: This equipment complies with RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 8.66 inches (22 cm) between the radiator and your body for 2.4 GHz, 5 GHz, and 6GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. n Déclaration e la concernant l’exposition aux rayonnements à fréquence radioélectrique (FR): Cet appareil est conforme aux limites d’exposition aux rayonnements FR établies par la FCC. Il doit être installé et utilisé à une distance minimale de 22 cm (8.66 pouces) entre le radiateur et votre corps, qu’il opère sur la bande 2,4 GHz, 5 GHz, ou 6GHz. Cet émetteur ne doit pas être installé ou utilisé à proximité immédiate d’une autre antenne ni d’un autre transmetteur.
Proper Disposal of HPE Aruba Networking Equipment
HPE Aruba Networking equipment complies with countries’ national laws for proper disposal and electronic waste management.
Waste of Electrical and Electronic Equipment
HPE Aruba Networking, a Hewlett Packard Enterprise company products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossedout wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2012/19/EU on Waste of Electrical and Electronic Equipment (WEEE).
European Union RoHS
HPE Aruba Networking, a Hewlett Packard Enterprise company products also comply with the EU Restriction of Hazardous Substances Directive 2011/65/EU (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the “RoHS” label shown at the left indicating conformance to this Directive.
HPE Aruba Networking 750 Series Campus Access Points | 25
India RoHS
This product complies with the “India E-waste (Management) Rules, 2016” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule II of the Rule.
HPE Aruba Networking 750 Series Campus Access Points | Installation Guide
26
China RoHS
HPE Aruba Networking products also comply with China environmental declaration requirements and are labeled with the “EFUP 50” label shown at the left.
HPE Aruba Networking 750 Series Campus Access Points | 27
Taiwan RoHS
Turkey RoHS material content declaration
Türkiye Cumhuriyeti: AEEE Yönetmeliine Uygundur
HPE Aruba Networking 750 Series Campus Access Points | Installation Guide
28
Documents / Resources
 |
HPE Aruba Networking 750 Series Campus Access Points [pdf] Installation Guide 750 Series Campus Access Points, 750 Series, Campus Access Points, Access Points, Points |
 |
HPE aruba networking 750 Series Campus Access Points [pdf] User Guide AP-754, AP-755, 750 Series Campus Access Points, 750 Series, Campus Access Points, Access Points |