ECS4125-10P 2.5G L2 Plus Lite L3 Multi Gig Ethernet Switch
Specifications
- Size (WxDxH): 330 x 207.9 x 47.3 mm (12.99 x 8.19 x 1.86
in.) - Weight: ECS4125-10P: 2.41 kg (5.31 lb), ECS4125-10T: 1.98 kg
(4.36 lb) - Temperature: Operating: 10% to 90% (non-condensing)
- Power Consumption: ECS4125-10P: 370 Watts maximum, ECS4125-10T:
36 Watts maximum - PoE Budget: 240 Watts (ECS4125-10P)
- Input Power Rating: ECS4125-10P: 100-240 VAC, 50-60Hz, 4 A,
ECS4125-10T: 100-240 VAC, 50-60Hz, 0.9 A
Product Usage Instructions
1. Installation
Note: The drawings in this document are for illustration only
and may not match your particular model.
Ground the Device
Attach a lug (not provided) to a #18 AWG minimum grounding wire
(not provided), and connect it to the grounding point on the rear
panel. Then connect the other end of the wire to rack ground.
Mount the Device
1. Attach the Brackets: Use the included screws to attach the
brackets.
2. Mount the Device: Mount the device in the rack and secure it
with rack screws.
Note: The device can also be installed on a desktop or shelf
using the included adhesive rubber feet.
Connect Power
Connect an AC power source to the device.
Make Network Connections
RJ-45 PoE Ports: Connect Cat. 5e or better twisted-pair
cable.
SFP+ Ports: Install transceivers and then connect fiber optic
cabling to the transceiver ports. Supported transceivers include:
1000BASE-SX/LX/EX/ZX and 1000BASE-T (RJ-45),
10GBASE-SR/LR/ER/ZR.
2. Make Management Connections
RJ-45 Console Port: Connect the included console cable and
configure the serial connection to 115200 bps, 8 characters, no
parity, one stop bit, 8 data bits, and no flow control.
FAQ
Q: How do I know if the device is properly powered on?
A: Check the SYS LED on the device which should be green for
‘OK’ status.
Q: What type of cables can be used with the RJ-45 PoE
Ports?
A: Use Cat. 5e or better twisted-pair cables for connecting to
the RJ-45 PoE Ports.
Quick Start Guide
2.5G L2+/Lite L3 Multi-Gig Ethernet Switch
ECS4125-10P | ECS4125-10T
Package Contents
www.edge-core.com
1
2
3
4
5
6
1. ECS4125-10P or ECS4125-10T Switch 2. Rack mounting kit–2 brackets and 8 screws 3. Power cord 4. Four adhesive rubber feet
5. Console cable–RJ-45 to DE-9 6. QR code label (affixed to the top of the switch)
ECS4125-10P 3
Overview
ECS4125-10T 3
1
2
1. System LEDs 2. Console port 3. 8 x 10/100/1G/2.5G RJ-45 PoE ports 4. 2 x 1/10G SFP+ ports 5. Ground screw 6. AC power socket
ECS4125-10P
4
5 6
1
2
1. System LEDs 2. Console port 3. 8 x 10/100/1G/2.5G RJ-45 ports 4. 2 x 1/10G SFP+ ports 5. Ground screw 6. AC power socket
System/Port LEDs
ECS4125-10T
4
5 6
3
1
2
4
3
1
2
4
1. Sys: Green (OK), Blinking Green (booting), Orange (faulf) 2. PWR: Green (OK), Orange (maximum PoE budget) 3. RJ-45 Ports: Green/Blinking (link/activity), Orange (PoE link) 4. SFP+ Ports: Green (10G), Orange (1G)
1. SYS: Green (OK), Blinking Green (booting), Orange (faulf) 2. PWR: Green (OK) 3. RJ-45 Ports: Green (2.5G), Orange (1G/100M/10M) 4. SFP+ Ports: Green (10G), Orange (1G)
1
E012025-CS-R03 150200002341A
Installation
Warning: For a safe and reliable installation, use only the accessories and screws provided with the device. Use of other accessories and screws could result in damage to the unit. Any damages incurred by using unapproved accessories are not covered by the warranty. Avertissement: Pour une installation sûre et fiable, utilisez uniquement les accessoires et les vis fournies avec l’appareil. L’utilisation d’autres accessoires et vis pourrait endommager l’appareil. Les dommages causés par l’utilisation d’accessoires non approuvés ne sont pas couverts par la garantie.
Note: The drawings in this document are for illustration only and may not match your particular model.
2 Ground the Device
Quick Start Guide
1 Mount the Device
Attach a lug (not provided) to a #18 AWG minimum grounding wire (not provided), and connect it to the grounding point on the rear panel. Then connect the other end of the wire to rack ground.
3 Connect Power
1. Attach the Brackets Use the included screws to attach the brackets.
Connect an AC power source to the device.
4 Make Network Connections
2. Mount the Device Mount the device in the rack and secure it with rack screws.
Note: The device can also be installed on a desktop or shelf using the included adhesive rubber feet.
RJ-45 PoE Ports Connect Cat. 5e or better twisted-pair cable.
SFP+ Ports Install transceivers and then connect fiber optic cabling to the transceiver ports. The following transceivers are supported:
1000BASE-SX/LX/EX/ZX and 1000BASE-T (RJ-45) 10GBASE-SR/LR/ER/ZR
2
Quick Start Guide
5 Make Management Connections
RJ-45 Console Port Connect the included console cable and then configure the serial connection: 115200 bps, 8 characters, no parity, one stop bit, 8 data bits, and no flow control.
Hardware Specifications
Size (WxDxH)
330 x 207.9 x 47.3 mm (12.99 x 8.19 x 1.86 in.)
Weight
ECS4125-10P: 2.41 kg (5.31 lb) ECS4125-10T: 1.98 kg (4.36 lb)
Temperature
Operating: 0° C to 50° C (32° F to 122° F) Storage: -40° C to 70° C (-40° F to 158° F)
Humidity
Operating: 10% to 90% (non-condensing)
Power Consumption
ECS4125-10P: 370 Watts maximum ECS4125-10T: 36 Watts maximum
PoE Budget
240 Watts
(ECS4125-10P)
Input Power Rating
ECS4125-10P: 100-240 VAC, 50-60Hz, 4 A ECS4125-10T: 100-240 VAC, 50-60Hz, 0.9 A
Regulatory Compliances
Emissions
EN 55032:2015/A1:2020 EN IEC 61000-3-2:2019/A1:2021 EN 61000-3-3:2013/A2:2021 FCC Class A VCCI-CISPR 32:2016 Class A BSMI (CNS 15936)
Immunity
IEC 61000-4-2/3/4/5/6/8/11 EN 55035:2017/A11:2020
Safety
UL (CSA 22.2 No 62368-1 & UL62368-1) CB (IEC/EN 62368-1) BSMI (CNS 15598-1)
Taiwan RoHS
CNS 15663
3
Quick Start Guide
Safety and Regulatory Information
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
You may use unshielded twisted-pair (UTP) for RJ-45 connections Category 3 or better for 10 Mbps connections, Category 5 or better for 100 Mbps connections, Category 5, 5e, or 6 for 1000 Mbps connections. For fiber optic connections, you may use 50/125 or 62.5/ 125 micron multimode fiber or 9/125 micron single-mode fiber.
CE Mark
CE Mark Declaration of Conformance for EMI and Safety (EEC)
This information technology equipment complies with the requirements of the Council Directive 2014/30/EU on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 2014/ 35/EU for electrical equipment used within certain voltage limits. For the evaluation of the compliance with these Directives, the following standards were applied:
RFI Emission: Limit according to EN 55032
Immunity: Product family standard according to EN 55035 Electrostatic Discharge according to EN 61000-4-2 / IEC 61000-4-2 Radio-frequency electromagnetic field according to EN IEC 61000-4-3 Electrical fast transient/burst according to EN 61000-4-4 / IEC 61000-4-4 Surge immunity test according to EN 61000-4-5 / IEC 610004-5 Immunity to conducted disturbances, Induced by radiofrequency fields: EN 61000-4-6 / IEC 61000-4-6 Power frequency magnetic field immunity test according to EN 61000-4-8 / IEC 61000-4-8 Voltage dips, short interruptions and voltage variations immunity test according to EN IEC 61000-4-11
LVD:
EN 62368-1:2014+A11:2017 EN IEC 62368-1:2020+A11:2020
The Declaration of Conformity (DoC) can be obtained from www.edgecore.com -> support -> download.
Mayflex UK Ltd Junction Six Industrial Park, Electric Avenue, Birmingham B6 7JJ United Kingdom
Vesper Technologies Limited Unit 5/6 Rugby Park, Bletchley Road, Heaton Mersey, Stockport SK4 3EJ United Kingdom
Japan – VCCI Class A
Laser Safety
Warning: Fiber Optic Port Safety:
CLASS 1 LASER PRODUCT
When using a fiber optic port, never look at the transmit laser while it is powered on. Also, never look directly at the fiber TX port and fiber cable ends when they are powered on.
Avertissment: Ports pour fibres optiques – sécurité sur le plan optique:
PRODUIT LASER DE CLASSE 1
Ne regardez jamais le laser tant qu’il est sous tension. Ne regardez jamais directement le port TX (Transmission) à fibres optiques et les embouts de câbles à fibres optiques tant qu’ils sont sous tension.
:
TX
Power Safety
Caution – Risk of Electrical Shock: To disconnect power, remove all power cords from the unit.
Attention – Risque de Choc Électrique: Pour débrancher, l’alimentation électrique, veuillez assurer tous les cables d’alimentation sont retires de l’unite.
– : – – , – ,
Power Cord Safety
Please read the following safety information carefully before installing the device:
Warning: Installation and removal of the unit must be carried out by qualified personnel only.
The unit must be connected to an earthed (grounded) outlet to comply with international safety standards.
Do not connect the unit to an A.C. outlet (power supply) without an earth (ground) connection.
The appliance coupler (the connector to the unit and not the wall plug) must have a configuration for mating with an EN 60320/IEC 320 appliance inlet.
The socket outlet must be near to the unit and easily accessible. You can only remove power from the unit by disconnecting the power cord from the outlet.
This unit operates under SELV (Safety Extra Low Voltage) conditions according to IEC 60950. The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions.
France and Peru only
4
This unit cannot be powered from IT supplies. If your supplies are of IT type, this unit must be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the secondary connection point labeled Neutral, connected directly to earth (ground).
Impédance à la terre
Important! Before making connections, make sure you have the correct cord set. Check it (read the label on the cable) against the following:
Power Cord Set
U.S.A. and Canada
The cord set must be UL-approved and CSA certified. The minimum specifications for the flexible cord are: – Min. 1.5 m and Max. 4.5 m long, Type SJE, SJT, ST or SJTO, No. 18 AWG. – Min. 1.5 m and Max. 2.4 m long, Type SVT or SPT-2, No. 18 AWG – 3-conductor The cord set must have a rated current capacity of at least 10 A. The attachment plug must be an earth-grounding type with NEMA 5-15P (10 A, 125 V) configuration.
Denmark
The supply plug must comply with Section 107-2-D1, Standard DK2-1a or DK2-5a.
Switzerland The supply plug must comply with SEV/ASE 1011.
U.K.
The supply plug must comply with BS1363 (3-pin 13 A)
and be fitted with a 5 A fuse which complies with BS1362.
The mains cord must comply with IEC 60227 (designation
60227 IEC 52).
Europe
The supply plug must comply with CEE7/7 (“SCHUKO”). The mains cord must comply with IEC 60227 (designation 60227 IEC 52). IEC-320 receptacle.
AC
EN 60320/IEC 320
IEC 60950 SELV
SELV
IT IT 1:1 230 V 2P+T Impédance à la terre
Quick Start Guide
UL CSA – 1.5 4.5 18 AWG , SJE, SJT, ST SJTO – 1.5 2.4 18 AWG , SVT SPT-2 – 3 10 A NEMA 5-15P 10 A125 V
DK2-1a DK2-5a 1072-D1
SEV/ASE 1011
BS1363 3 13 A BS1362 5 A IEC 60227 60227 IEC 52
CEE7/7 “SCHUKO” IEC 60227 60227 IEC 52 IEC-320
Veuillez lire à fond l’information de la sécurité suivante avant d’installer l’appareil:
Avertissement: L’installation et la dépose de ce groupe doivent être confiés à un personnel qualifié.
Ne branchez pas votre appareil sur une prise secteur (alimentation électrique) lorsqu’il n’y a pas de connexion de mise à la terre (mise à la masse).
Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de respecter les normes internationales de sécurité.
Le coupleur d’appareil (le connecteur du groupe et non pas la prise murale) doit respecter une configuration qui permet un branchement sur une entrée d’appareil EN 60320/IEC 320.
La prise secteur doit se trouver à proximité de l’appareil et son accès doit être facile. Vous ne pouvez mettre l’appareil hors circuit qu’en débranchant son cordon électrique au niveau de cette prise.
L’appareil fonctionne à une tension extrêmement basse de sécurité qui est conforme à la norme IEC 60950. Ces conditions ne sont maintenues que si l’équipement auquel il est raccordé fonctionne dans les mêmes conditions.
France et Pérou uniquement:
Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos alimentations sont du type impédance à la terre, ce groupe doit être alimenté par une tension de 230 V (2 P+T) par le biais d’un transformateur d’isolement à rapport 1:1, avec un point secondaire de connexion portant l’appellation Neutre et avec raccordement direct à la terre (masse).
5
Quick Start Guide
Cordon électrique – Il doit être agréé dans le pays d’utilisation
Etats-Unis et Canada:
Le cordon doit avoir reçu l’homologation des UL et un certificat de la CSA. Les spécifications minimales pour un cable flexible sont: – Câble No. 18 AWG, Min. 1,5 mètre et Max. 4.5 mètres de long, Type SJE, SJT, ST ou SJTO. – Câble No. 18 AWG, Min. 1,5 mètre et Max. 2,4 mètres de long, Type SVT ou SPT-2. – 3 conducteurs. Le cordon doit être en mesure d’acheminer un courant nominal d’au moins 10 A. La prise femelle de branchement doit être du type à mise à la terre (mise à la masse) et respecter la configuration NEMA 5-15P (10 A, 125 V).
Danemark: La prise mâle d’alimentation doit respecter la section 107-2 D1 de la norme DK2 1a ou DK2 5a.
Suisse:
La prise mâle d’alimentation doit respecter la norme SEV/ ASE 1011.
Europe
La prise secteur doit être conforme aux normes CEE 7/7 (“SCHUKO”) Le cordon d’alimentation doit être conforme à la norme IEC 60227 (IEC 60227 désignation 52)
Warnings and Cautionary Messages
Warning: This product does not contain any serviceable user parts. Warning: Installation and removal of the unit must be carried out by qualified personnel only. Warning: When connecting this device to a power outlet, connect the field ground lead on the tri-pole power plug to a valid earth ground line to prevent electrical hazards. Warning: This device uses lasers to transmit signals over fiber optic cable. The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation. However, you should never look directly at a transmit port when it is powered on. Warning: When selecting a fiber SFP+ device, considering safety, please make sure that it can function at a temperature that is not less than the recommended maximum operational temperature of the product. You must also use an approved Laser Class 1 SFP+ transceiver. Caution: Wear an anti-static wrist strap or take other suitable measures to prevent electrostatic discharge when handling this equipment. Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Caution: Use only twisted-pair cables with RJ-45 connectors that conform to FCC standards.
Avertissement: Ce produit ne contient aucun composant susceptible d’être réparé par l’utilisateur. Avertissement: L’installation et la dépose de l’unité ne doivent être réalisées que par du personnel qualifié. Avertissement: Lorsque vous branchez cet appareil sur une prise électrique, la terre de la fiche à trois pôles doit être branchée sur une ligne mise à la terre pour écarter tout danger électrique. Avertissement: Cet appareil utilise des lasers pour transmettre des signaux via un câble de fibre optique. Ces lasers répondent aux exigences des produits laser de classe 1 et sont sans danger intrinsèque pour les yeux, sous réserve de leur utilisation normale. Vous ne devrez cependant jamais regarder directement un port de transmission lorsque ce dernier est sous tension. Avertissement: Lorsque vous utilisez un dispositif fibre de type SFP+, en ce qui concerne la sécurité, assurez-vous qu’il puisse fonctionner à une température inférieure à la température maximale de fonctionnement recommandée du produit. Utilisez également un émetteur-récepteur laser SFP+ de classe 1 agrée.
Attention: La manipulation de cet équipement requiert le port d’un bracelet antistatique ou l’utilisation d’autres mesures pour éviter toute décharge électrostatique. Attention: Ne branchez pas un connecteur téléphonique dans le port RJ-45. Vous risqueriez d’endommager l’appareil. Attention: Ne branchez que des fils torsadés par paires conformes aux normes FCC sur les connecteurs RJ-45.
1 SFP+ 1 SFP+
RJ-45 FCC RJ-45
CQC (China)
BSMI (Taiwan)
/
6
IC
:
: : 1 : 886-3-5770270
Products contain hazardous substances exposing table
Component Name
Hazardous Substances Project
(Pb) (Cd) (Hg) (Cr)
(PBB)
(PBDE)
Power Supply
¯¯
¯
¯
¯
Fan
¯¯
¯
¯
¯
Heat Sink
¯¯
¯
¯
¯
RJ45+X’FMR
¯¯
¯
¯
¯
TVS Array
¯¯
¯
¯
¯
Diode
¯¯
¯
¯
¯
Resistor
¯¯
¯
¯
¯
SJ/T: 11364-2014 b
¯ : GB/T 26572-2011 b
¯ : Indicates the toxic or hazardous substance content of the part (at the homogenous material
level) is lower than the threshold defined by Requirements for Concentration Limits for Toxic or
hazardous Substances in Electronic Information Products (GB/T 26572-2011) issued by Chinese
Ministry of Information Industry (“Not Contained” toxic or hazardous substances).
: GB/T 26572-2011 b
: Indicates the toxic or hazardous substance content of the part (at the homogenous material level)
is over the threshold defined by standard of GB/T 26572-2011 (“Contained” toxic or hazardous
substances). Suppliers can explain the technical cause of “X” according to actual situation.
b b
The Environment- Friendly Use Period (EFUP) for all enclosed products and their
parts are per the symbol shown here, unless otherwise marked. Certain parts may
have a different EFUP (for example, battery modules) and so are marked to reflect
such. The Environment- Friendly Use Period is valid only when the product is
operated under the conditions defined in the product manual.
Quick Start Guide
‘HFODUDWLRQRIWKH3UHVHQFH&RQGLWLRQRIWKH5HVWULFWHG6XEVWDQFHV0DUNLQJ
*/ 8OWUD3R(
(&63
(TXLSPHQW1DPH
7SH’HVLJQDWLRQ7SH
8QLW
5HVWULFWHGVXEVWDQFHVDQGLWVFKHPLFDOVPEROV
3E
+J
&G
&U
3%%
3%'(
3&%$
£
)DQ
£
&KDVVLV
&DEOHDVV
3RZHU6XSSO
£
ZW ZW
1 R W H ([FHHGLQJZWDQGH[FHHGLQJZWLQGLFDWHWKDWWKHSHUFHQWDJHFRQWHQW RIWKHUHVWULFWHGVXEVWDQFHH[FHHGVWKHUHIHUHQFHSHUFHQWDJHYDOXHRISUHVHQFH FRQGLWLRQ
1 R W H LQGLFDWHVWKDWWKHSHUFHQWDJHFRQWHQWRIWKHUHVWULFWHGVXEVWDQFHGRHVQRW H[FHHGWKHSHUFHQWDJHRIUHIHUHQFHYDOXHRISUHVHQFH
£
1 R W H 7KH £ LQGLFDWHVWKDWWKHUHVWULFWHGVXEVWDQFHFRUUHVSRQGVWRWKHH[HPSWLRQ
Products contain hazardous substances exposing table
Component Name
Hazardous Substances Project
(Pb) (Cd) (Hg) (Cr)
(PBB)
(PBDE)
Power Supply
¯¯
¯
¯
¯
FAN
¯¯
¯
¯
¯
Heat Sink
¯¯
¯
¯
¯
RJ45+X’FMR
¯¯
¯
¯
¯
Diode
¯¯
¯
¯
¯
TVS Array
¯¯
¯
¯
¯
Resistor
¯¯
¯
¯
¯
SJ/T: 11364-2014 b
¯ : GB/T 26572-2011 b
¯ : Indicates the toxic or hazardous substance content of the part (at the homogenous material
level) is lower than the threshold defined by Requirements for Concentration Limits for Toxic or
hazardous Substances in Electronic Information Products (GB/T 26572-2011) issued by Chinese
Ministry of Information Industry (“Not Contained” toxic or hazardous substances).
: GB/T 26572-2011 b
: Indicates the toxic or hazardous substance content of the part (at the homogenous material level)
is over the threshold defined by standard of GB/T 26572-2011 (“Contained” toxic or hazardous
substances). Suppliers can explain the technical cause of “X” according to actual situation.
b b
The Environment- Friendly Use Period (EFUP) for all enclosed products and their
parts are per the symbol shown here, unless otherwise marked. Certain parts may
have a different EFUP (for example, battery modules) and so are marked to reflect
such. The Environment- Friendly Use Period is valid only when the product is
operated under the conditions defined in the product manual.
‘HFODUDWLRQRIWKH3UHVHQFH&RQGLWLRQRIWKH5HVWULFWHG6XEVWDQFHV0DUNLQJ
*/
(&67
(TXLSPHQW1DPH
7SH’HVLJQDWLRQ7SH
8QLW
5HVWULFWHGVXEVWDQFHVDQGLWVFKHPLFDOVPEROV
3E
+J
&G
&U
3%%
3%'(
3&%$
£
3RZHU6XSSO £
)$1
£
&KDVVLV
&DEOHDVV
ZW ZW
1 R W H ([FHHGLQJZWDQGH[FHHGLQJZWLQGLFDWHWKDWWKHSHUFHQWDJHFRQWHQW RIWKHUHVWULFWHGVXEVWDQFHH[FHHGVWKHUHIHUHQFHSHUFHQWDJHYDOXHRISUHVHQFH FRQGLWLRQ
1 R W H LQGLFDWHVWKDWWKHSHUFHQWDJHFRQWHQWRIWKHUHVWULFWHGVXEVWDQFHGRHVQRW H[FHHGWKHSHUFHQWDJHRIUHIHUHQFHYDOXHRISUHVHQFH
£
1 R W H 7KH £ LQGLFDWHVWKDWWKHUHVWULFWHGVXEVWDQFHFRUUHVSRQGVWRWKHH[HPSWLRQ
Warranty Information and Technical Support Registering your product enables you to receive a more efficient warranty service. Be sure to register at www.edge-core.com.
7
Documents / Resources
 |
Edgecore Networks ECS4125-10P 2.5G L2 Plus Lite L3 Multi Gig Ethernet Switch [pdf] User Guide ECS4125-10P, ECS4125-10T, ECS4125-10P 2.5G L2 Plus Lite L3 Multi Gig Ethernet Switch, ECS4125-10P, 2.5G L2 Plus Lite L3 Multi Gig Ethernet Switch, Lite L3 Multi Gig Ethernet Switch, Multi Gig Ethernet Switch, Gig Ethernet Switch, Ethernet Switch |
