Danfoss KPU Series Temperature and Pressure Controls
Specifications
- Bulb Type: Remote bulb
- Contact/Reset: -30 to 80 SPST/Auto
- Maximum Tube Length at Lowest Bulb: 120 inches
KPU 60/70 Thermostats
- Bulb Type: Remote air coil
- Contact/Reset: -20 to 60 SPDT/Auto
- Capillary Tube Length: 80 inches
- Differential at Lowest Temp. Setting: 10 to 40
- Differential at Highest Temp. Setting: 2.5 to 13
KPU Pressure Switches
- Pressure System: Low (in. Hg/psig)
- Reset: Automatic
- Contact: SPDT
- Range: 6 to 108 psig
- Differential: 10 to 60 psig
KPU Dual Pressure Switches
- Low Pressure Side Range: 6 to 108 (in. Hg/psig)
- High Pressure Side Range: 100 to 465 psig
- Reset: Automatic
- Contact System: SPST (NO/NC)
- Max. Working Pressure: 250/510 psig
Temperature and pressure controls are designed with the contractor in mind
KPU temperature and pressure controls are designed for easy installation and service. They feature bottom and rear knockouts, differential adjustment dial, a tamper-resistant design, and a robust thermoplastic housing. Danfoss KPU temperature and pressure controls maintain precise set point values and are easy to set and adjust. Learn more about how to select the right Danfoss products for your needs at choose.danfoss.com.
- Reliable temperature and Pressure control systems are designed for flawless performance.
Technical data and ordering
- KPU 19 Thermostats
As 060L1250 is SPDT, 060L2150 can replace competitor parts crossed to both 060L2150 and 060L2151.
Technical data and ordering
KPU 60/70 Thermostats
Technical data and ordering
KPU Pressure Switches
KPU Dual Pressure Switches
- Competitor part no. Equipped with a capillary tube for all but P170LB-1C, which has flare connections.
- KPU 6 and the high-pressure side of KPU 16 are designed with fail-safe double bellows.
- Convertible reset controls can be adjusted for either automatic or manual reset. Adjust the reset setting to match the product being replaced. All controls are supplied with universal mounting bracket and mounting screws.
- Ambient temperature: -40°F to ++122°F(17175°For a maximum of 2 hours). KPU 1, 2, 6, 16 are suitable for all HFC refrigerants, including R-410A.
Spare Parts and Accessories
For the complete portfolio of KPU products, scan the QR code to access the Quick Select Guide.
Installation
- Ensure the power source is switched off before installation.
- Locate an appropriate placement for the temperature and pressure controls.
- Use bottom and rear knockouts for easy installation.
Setting and Adjusting
- Use the differential adjustment dial to set precise values.
- Adjust the controls as needed for your specific requirements.
Maintenance
- Regularly check for any tampering with the controls.
- Clean the thermoplastic housing to ensure proper functioning.
Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order, provided that such alterations can be made without subsequent changes being necessary in specifications already agreed upon. All trademarks in this material are the property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
FAQs
Q: Can competitor parts be replaced with Danfoss products?
A: Yes, some competitor parts can be replaced with specific Danfoss codes as mentioned in the manual.
Q: What is the maximum working pressure for the KPU Pressure Switches?
A: The maximum working pressure varies depending on the specific model, ranging from 250 to 675 psig.
Documents / Resources
 |
Danfoss KPU Series Temperature and Pressure Controls [pdf] Owner's Manual KPU 19, KPU 61, KPU 62, KPU 70, KPU 73, KPU Series Temperature and Pressure Controls, KPU Series, Temperature and Pressure Controls, Pressure Controls, Controls |