RC 1.2 Reverse Camera
“
SPECIFICATIONS
- Features:
- CMOS Image Sensor
- NTSC TV System
- Effective Pixels: 750TVL
- Image Resolution: 25 Frame Per Second
- Exposure & Gain Control: 1/60~1/100000sec
- Electronic Shutter: Auto
- White Balance
- Illumination: 0.1 Lux/F
- Horizontal View: 160mA-180mA
- Vertical View
- Diagonal View
- DC12V Voltage
- Current DC9-16V
- Operating Voltage Range
- Operating Temperature
- Storage Temperature
- Protection Grade: IP68
- RCA/4 PIN DIN Lens: 4-Layer Lens
PRODUCT USAGE INSTRUCTIONS
1. Operating Instructions
Before using the reverse camera RC 1.2, ensure that the vehicle
is parked safely and the engine is turned off.
2. Installation Instructions
Rear Camera Installation:
- Connect the rear camera to the display monitor or car radio
using the provided cables. - Ground the wire through the exterior body of the vehicle and
ensure a secure connection. - Follow the provided installation diagram for proper wiring and
connection.
Front Camera Installation:
- Mount the front camera in a suitable location on the
vehicle. - Connect the front camera to the display monitor or car radio
using the provided cables. - Ground the wire through the exterior body of the vehicle and
ensure a secure connection.
3. After Installation Instructions
Adjust the viewing angle of the camera as needed for optimal
visibility.
FAQ
Q: Can I install the reverse camera on my own?
A: While installation instructions are provided, it is
recommended to seek professional help for accurate installation to
avoid any damage to the vehicle components.
Q: What should I do if the camera does not display
correctly?
A: Check the connections and ensure all wiring is properly
connected. If issues persist, consult the user manual or contact
customer support for assistance.
“`
REVERSE CAMERA RC 1.2
Enjoy it.
Operating and Installation Instructions
CAUTIONS
Safety Notes
· Unit does not record video.
This vehicle security system has been manufactured according to established safety guidelines. However, dangers may still occur if the safety notes in this manual is not observed. This manual is intended to familiarize the user with the reverse camera important functions. Read this carefully, prior to using the reverse camera. Keep this manual in an easily accessible location. In addition, do observe the instructions of the devices used in conjunction with this reverse camera.
Attentions
· Assign a mounting location that will not obstruct driver in any circumstances. Or cause injuries to drives and passengers in case of emergency brake or accidents.
· Ensure all wires are connected properly, and that the unit is functioning well before
· Avoid automatic car wash or high-pressure water to prevent water and pressure from damaging the camera or causing
· Do not install this unit near heater outlet.
This manual may be updated from time to time without any notice.
Disclaimer In no event shall Blaupunkt be liable for any direct, indirect, punitive, incidental, special consequential damages to property or life and whatsoever arising out of or connected with the use or misuse of our products. USA & CANADA: This product is not intended for sale in the United States and Canada. If purchased in the U.S. or Canada, this product is purchased on as-is basis. No warranty, whether expressed or implied is provided in the U.S. or Canada.
· Any unauthorized installation, disassembly
the unit and void warranty of the unit.
· Always use only the parts that are included with the units only.
· Do not damage vehicle components when drilling holes for the mount.
· provided here. Consult an authorized Blaupunkt dealer or vehicle’s manufacturer if the information provided here does not
· This unit is applicable for front and reverse AHD camera use. Consult an authorized Blaupunkt dealer during installation.
1
SPECIFICATIONS
Features CMOS Image Sensor NTSC TV System Effective Pixels 750TVL Image Resolution 25 Frame Per Second Exposure & Gain Control 1/60~1/100000sec Electronic Shutter Auto White Balance Illumination Min. Horizontal View Vertical View Diagonal View DC12V Voltage Current DC9-16V Operating Voltage Range Operating Temperature Storage Temperature Protection Grade RCA/4 PIN DIN Lens
RC1.2
652 (H) x 492 (V)
0.1 Lux/F
140°H
105°V
170°D
160mA-180mA
-20-60°C
-20-60°C
IP68
4-Layer Lens
2
INSTALLATION DIAGRAM
a) Rear Camera Display Monitor/ Car Radio
Video (Yellow)
a)With Parking Line White Blue
b)Remove Parking Line White Blue
Power Supply (Red)
Reverse Camera
P
R N D
L 2
Reverse Trigger
Reverse Light
Ground the wire through the exterior body of the vehicle and keep connection intact.
b) Front Camera
Display Monitor/ Car Radio
Video (Yellow)
White
Power Supply (Red)
Blue
Front
ACC
Camera
Ground the wire through the exterior body of the vehicle and keep connection intact.
INSTALLATION LOCATION
Front Camera
Reverse Camera
Display Monitor/ Car Radio
Attention · Remove protective film from camera lens before use. · Take extra precautions when setting up the connection near petrol tank and wires. · Connect Red Wire with reverse light.
3
INSTALLATION LOCATION
Tail Light
1 Remove one side of the reverse light socket from its housing then remove the bulb from its socket.
2 Connect the reverse light power cable to the camera, screwn the housing & camera back into position with a screwdriver.
TYPE 1
TYPE 2
Hatch Handle
1 Use a screwdriver to remove the original hatch handle
2 Mount the camera where the original hatch handle used to be
Car Plate
1 Remove the rotating mount before installation. Drill an access hole for the camera cables
2 Mount the camera onto the acces hole & secure it in position with 3M tape/ screws
TYPE 3
After Installation
Adjust Viewing Angle
Remarks : 1. Pictures are for illustration purpose only, see actual vehicle for accurate installation location. 2. Ensure diameter of hole size is correct before drilling. 3. Ensure drilling process does not harm the component of the vehicle. 4. Assign mounting location that will not obstruct camera view.
4
FRONT / REVERSE CAMERA INSTALLATION
FRONT/ REAR VIEW DISPLAY & PARKING LINE Reverse Camera Wiring (Remove Parking Line)
Reverse Camera Do not cut the wires when using as reverse camera.
Reverse Camera Cut blue wire when using as reverse camera to remove parking line.
Front Camera Wiring (Flip Viewing Display & Remove Parking Line)
Reverse Camera Do not cut the wire when using as reverse camera.
Front Camera Cut white & blue wires when using as front camera to display & remove parking line.
5
TROUBLESHOOTING
If any of the following problem occur, please resort to Troubleshooting for the possible solutions. Consult Blaupunkt authorized dealer if problem persist.
Problem Display monitor / car radio does not show reverse view when reversing. Reverse view does not show even after restarting the display monitor/ car radio. Reverse view does not show even though power supplies of the reverse light or the rear car plate light is properly connected.
Solution Restart the display monitor / car radio.
Examine if the power supplies of the reverse light or the rear car plate light is properly connected. Examine if the power supply cables of the reverse light or the rear car plate light is damaged. Repair/replace if the cables are damaged.
6
Blaupunkt Car Entertainment – Asia Pacific Competence Centre 1 331 24 019 32 01
Documents / Resources
 |
BLAUPUNKT RC 1.2 Reverse Camera [pdf] Installation Guide RC 1.2 Reverse Camera, RC 1.2, Reverse Camera, Camera |