AVTech SATURN700RGB 700W Power LED Tilt Moving Strobe User Manual

After receiving the lights, check for any damages caused by transportation. If there are damages, do not use the device and contact your dealer or manufacturer immediately.

Do not install the fixture on inflammable surfaces directly.
The fixture should only be handled by qualified personnel for installation, operation, and maintenance.

Maintain a minimum distance of 3 meters when projecting the beam onto inflammable surfaces.

Dimensions

Refer to the product manual for detailed dimensions.

Control Panel

The control panel includes operation buttons for mode selection, power input/output details, ART-NET and DMX connections. Follow the specific panel operations as described in the manual.

Lighting Parameters

Refer to the Technical Data Sheet for detailed optical and electronic parameters of the product.

FAQ

Q: Can this product be used outdoors?

A: Yes, the product is suitable for both indoor and outdoor use with an IP65 rating.

Q: What is the power requirement for this product?

A: The input voltage range is 100-240V at 50/60Hz with a power output of 700W.

Before using this lamp, please read this manual thoroughly

Safety instructions

After receiving the lights, please open to check whether there is any damage caused by transportation.
In case of damages caused by transportation, please don’t this device and contact your dealer or manufacturer as soon as possible.

The projector is for indoor and outdoor use, IP65.
Do not install the fixtures onto inflammable surfaces directly.

The fixture is only intended for installation, operation and maintenance by qualified personnel.
Do not project the beam onto inflammable surfaces, minimum distance is 3 meters. 3m

Avoid direct exposure to the light from the lamp. The light is harmful to the eyes.
Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of the power supply match the power requirements of the fixture.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.
Do not connect this device to any other type of dimmer apparatus.
The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it should be attached as shown in the “Installing the projector” section.
Shields and lenses shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired, for example by cracks or deep scratches.
The exterior surface temperature of the luminaire after 5 minutes of operation is 45℃ when steady state is achieved 70℃. There are no user-serviceable parts inside the projector, do not open the housing and never operate the fixture with the covers removed.
There are no user-serviceable parts inside this light, please check whether all covers or shells have been installated and screws have beed tightened securely. It is forbidden to use lights with covers(or shells) open.
If you have any questions, don’t hesitate to consult your dealer or manufacturer.

Dimensions

control Panel

Panel operation buttons: mode UP Down Enter
power input: IP65 POWER CON cable Input voltage 100-240V 50/60HZ
Power Output: IP65 POWER CON power cable Output voltage 100-240V 50/60HZ
ART-NET input: Connect network input
DMX input: 3-core DMX waterproof signal line input
DMX output: 3-core DMX waterproof signal line output
ART-NET output: Connect network output
- The specific operations of the panel functions are as follows:

Display panel function description

Press the button UP or DOWN if you want to browse through the various Setup Options.
Press the button ENTER to save your settings or enter the next menu.

Press the button UP or DOWN to shift.
Press button Menu will return to the upper menu one by one.

Lighting parameter

Technical Data Sheet

Optical parameters
light source	1.56W white 392pcs 2835 lamp beams,1W RGB3 in1 784pc 5050 lamp beads
color temperature	2800K-8000K
Optical output of the whole machine	R:5480 Lm；G：11760 lm；B：1560 lm；W：45000 lm；ALL：63880 lm
Illumination	ALL:/ Lux: R：/ Lux: G：/ Lux: B：/ Lux: W：/ Lux: @5m
Colour rendering index	Ra≥90
R9	≥90
dominant wavelength	R：622nm；G：525nm；B：457nm
Light source life	20000H
beam angle	110°

dynamic effect
strobe	0～20Hz
Dimming	Four dimming curves, 0-100% dimming

Electronic parameters
Input voltage and frequency	100～240VAC,50～60Hz
power	Full brightness 700W，Strobe 1200W
power connection	Waterproof POWERCORN input;
signal connection	Waterproof 3-core DMX signal line input/output, the maximum number of connections is 32; waterproof network signal input and output
Power Factor	0.95 @230V
working environment	-10°～45°
switching power supply	100～240VAC, 50～60Hz,28V 800W

Structural parameters
Size	Product size：494×316×160 mm
Weight	Net weight：12.0Kg(Clamps and quick lock not included）
degree of protection	IP65
cooling system	Waterproof low-noise fan forced cooling
shell	Die-cast magnesium + aluminium alloy; black
installation method	side hanging, hanging installation

control
control method	Art-net/DMX512/RDM
DMX Channel	8/11/13/24/30/74/97CH
Display	TFT
refresh rate	600Hz/1200 Hz/2000 Hz/4000 Hz/6000 Hz/25KHz
pixel matrix	white light 214，rgb 27

Accessories
Standard	Standard power cord 1PC; manual 1PC
Optional

menu function

	Main Level	Programming Levels
1	Protocol	DMX512
		Art-Net
		sACN
2	DMX Address	1–512*
3	DMX Channel	8CH
		11CH
		13CH
		24CH
		30CH
		74CH
		97CH
4	Static	Fixed Color	R
			G
			B
			GB
			RB
			RG
			RGB
		Manual Color Mixer	Red	0-255
			Green
			Blue
5	Plate FX	Plate FX 1 Plate FX 2 Plate FX 3 Plate FX 4 Plate FX 5 Plate FX 6 Plate FX 7	Speed	1-100
			Plate Intensity	000-255
			Background Color	R
				G
				B
				GB

		Plate FX 8 Plate FX 9			RB
					RG
					RGB
					Off
				Foreground Color	R
					G
					B
					GB
					RB
					RG
					RGB
					Off
6	Beam Intensity	000-255
7	Beam Flash Duration	000-255
8	Beam Flash Rate	000-255
9	Tilt	000-255
10	Tilt Offset	000-255
11	Tilt Invert	No
		Yes
12	Pixel Invert	Plate1 Invert			No
					Yes
		Plate2 Invert			No
					Yes
		Tube1 Invert			No
					Yes
		Tube2 Invert			No
					Yes
13	LED Array Swap	Plate Swap			No
					Yes
		Beam Swap			No
					Yes
14	Master/Slave	Master
		Slave
15	Dimmer Mode	OFF
		DIM1–3
16	White Balance	Off
		Manual	Red Green Blue		125-255

17	LED Frequency	600Hz 1200Hz 2000Hz 4000Hz 6000Hz 25000Hz
18	Fan Mode	Auto
		On
19	Display Invert	No
		Yes
20	Backlight	10s
		30s
		2Min
		Always On
21	Key Lock	On
		Off
22	Ethernet Setting	Universe	0–255 (ArtNet)
			1–255 (sACN)
		IP Address	2.192.0.1
23	Information	Fixture Hours:	_ _ _Hours
		LED Hours:	_ _H
		Disp Ver:	V_._ _ _ _ _ _
		Drv-Y Ver:	V_._
		LED-A Ver:	V_._
		LED-C Ver:	V_._
		Net Ver:	V_._
		UID	_ _ _ _ _ _ _ _ _ _ _ _ _ _
24	Update Firmware	Only this Unit	_ _ _ _ _ _.CHL
			…
		Multiple Units	_ _ _ _ _ _.CHL
			…
		Other Fixture Type	_ _ _ _ _ _.CHL
			…
25	Factory Reset	No
		Yes

Installation and connection

Installation diagram

Precautions

This product is suitable for indoor and outdoor use, and its protection level is IP65. The lamp should be kept clean and should not be used in a humid or dusty environment. It should be maintained every three months.

Only qualified professionals can install, operate and maintain the lamps, and ensure that the operation is strictly under the procedures described in this manual.
The lamps and lanterns should be installed in a well-ventilated place, at least 50 away from the wall, and check whether the ventilation holes are unobstructed. Do not look directly at the light source to avoid damage to the eyes.
Parts that make electrical connections must be operated by qualified installers.

Each lamp should be safely grounded, and electrical installation should be carried out under relevant standards.
Do not use the power cord with damaged insulation, and do not put the power cord on other wires.
When the lamp is not in use or cleaned, please unplug the power cord. Do not pull or pull the power cord vigorously.

If the back cover of the lamp is equipped with a safety buckle or a connection hole, for safety reasons, please use the safety rope to pass through the connection hole for auxiliary hoisting.08

power connection

This product uses a Power con in/out

input power cord

Note: Due to the power, a 1.5 square power cord

Do not connect too many lamps to a single power cord, or overload it.

Do not use the power cord with damaged insulation, and do not put the power cord on other wires.

When the lamp is not in use or cleaning, please unplug the power cord。

Do not pull or plugin vigorously or drag the power cord directly.

signal connection

Internet connection

DMX Connection

DMX connection instructions

To reduce signal errors and avoid signal weakening and interference during transmission, a 120 ohm 1/4W resistor can be added between the 2-core and 3-core of the DMX output of the last machine.
Use the XLR signal cable to connect the lamps, one end to the output port of the lamp, and the other end to the input port of the next lamp. Signal lines can only be used in series, not in parallel.
Because the DMX512 signal transmission speed is very fast when the signal line is damaged, the welding place is not strong, the contact is not good, etc., it will affect the signal transmission and cause the system to shut down.

When the machine power of a certain unit is cut off, the connection of DMX output and input is bypassed to maintain the continuity of the DMX line.
Each light must have an address code to be able to receive information from the console.
The terminal of the DMX512 system needs to be equipped with a terminator to reduce errors in signal transmission.

DMX Address code setting

Ch	add	first address	Second, add	Third add	Fourth add
8CH	001-008	001	009	017	025
11CH	001-011	001	012	023	034
13CH	001-013	001	014	027	040
24CH	001-024	001	025	049	063
30CH	001-030	001	031	061	091
74CH	001-074	001	075	149	223
97CH	001-097	001	098	195	292

Refer to the above picture The number of lamps to be added after the fourth one; the address code is based on the channel, and so on.

channel table

97CH
Channel	Function	Value	Percent/Setting
1	Tilt	000-255	0-100％
2	Fine tilt	000-255	0-100％
3	Master dimmer	000-255	0-100％
4	Plate dimmer	000-255	0-100％
5	Beam dimmer	000-255	0-100％
6	Plate flash duration	000-009	Classic shutter mode: disables duration control
		010-250	Slow to fast
		251-255	100％On, no flash/strobe
7	Plate flash rate	000-009	100%
		010-250	Slow to fast
		251-255	100%
8	Beam flash duration	000-009	Classic shutter mode: disables duration control
		010-250	Slow to fast
		251-255	100％On, no flash/strobe
9	Beam flash rate	000-009	100%
		010-250	Slow to fast
		251-255	100%
10	Plate pixel 1 red	000-255	0-100％
11	Plate pixel 1 green	000-255	0-100％
12	Plate pixel 1 blue	000-255	0-100％
13	Plate pixel 2 red	000-255	0-100％
14	Plate pixel 2 green	000-255	0-100％
15	Plate pixel 2 blue	000-255	0-100％
16	Plate pixel 3 red	000-255	0-100％
17	Plate pixel 3 green	000-255	0-100％
18	Plate pixel 3 blue	000-255	0-100％
19	Plate pixel 4 red	000-255	0-100％
20	Plate pixel 4 green	000-255	0-100％
21	Plate pixel 4 blue	000-255	0-100％
22	Plate pixel 5 red	000-255	0-100％
23	Plate pixel 5 green	000-255	0-100％
24	Plate pixel 5 blue	000-255	0-100％
25	Plate pixel 6 red	000-255	0-100％
26	Plate pixel 6 green	000-255	0-100％
27	Plate pixel 6 blue	000-255	0-100％
28	Plate pixel 7 red	000-255	0-100％

29	Plate pixel 7 green	000-255	0-100％
30	Plate pixel 7 blue	000-255	0-100％
31	Plate pixel 8 red	000-255	0-100％
32	Plate pixel 8 green	000-255	0-100％
33	Plate pixel 8 blue	000-255	0-100％
34	Plate pixel 9 red	000-255	0-100％
35	Plate pixel 9 green	000-255	0-100％
36	Plate pixel 9 blue	000-255	0-100％
37	Plate pixel 10 red	000-255	0-100％
38	Plate pixel 10 green	000-255	0-100％
39	Plate pixel 10 blue	000-255	0-100％
40	Plate pixel 11 red	000-255	0-100％
41	Plate pixel 11 green	000-255	0-100％
42	Plate pixel 11 blue	000-255	0-100％
43	Plate pixel 12 red	000-255	0-100％
44	Plate pixel 12 green	000-255	0-100％
45	Plate pixel 12 blue	000-255	0-100％
46	Plate pixel 13red	000-255	0-100％
47	Plate pixel 13 green	000-255	0-100％
48	Plate pixel 13 blue	000-255	0-100％
49	Plate pixel 14 red	000-255	0-100％
50	Plate pixel 14 green	000-255	0-100％
51	Plate pixel 14 blue	000-255	0-100％
52	Beam pixel 1	000-255	0-100％
53	Beam pixel 2	000-255	0-100％
54	Beam pixel 3	000-255	0-100％
55	Beam pixel 4	000-255	0-100％
56	Beam pixel 5	000-255	0-100％
57	Beam pixel 6	000-255	0-100％
58	Beam pixel 7	000-255	0-100％
59	Beam pixel 8	000-255	0-100％
60	Beam pixel 9	000-255	0-100％
61	Beam pixel 10	000-255	0-100％
62	Beam pixel 11	000-255	0-100％
63	Beam pixel 12	000-255	0-100％
64	Beam pixel 13	000-255	0-100％
65	Beam pixel 14	000-255	0-100％
66	Beam pixel 15	000-255	0-100％
67	Beam pixel 16	000-255	0-100％
68	Beam pixel 17	000-255	0-100％
69	Beam pixel 18	000-255	0-100％
70	Beam pixel 19	000-255	0-100％
71	Beam pixel 20	000-255	0-100％

72	Beam pixel 21	000-255	0-100％
73	Beam pixel 22	000-255	0-100％
74	Beam pixel 23	000-255	0-100％
75	Beam pixel 24	000-255	0-100％
76	Beam pixel 25	000-255	0-100％
77	Beam pixel 26	000-255	0-100％
78	Beam pixel 27	000-255	0-100％
79	Beam pixel 28	000-255	0-100％
80	Beam FX	000-005	No function
		006-042	Ramp up
		043-085	Ramp down
		086-128	Ramp up-down
		129-171	Random
		172-214	Lightning
		215-255	Spikes
81	Plates foreground	000-000	No function
		001-002	White(2700K)
		003-004	White(3200K)
		005-006	White(4200K)
		007-008	White(5600K)
		009-010	White(8000K)
		011	Blue R:0 G:0 B:255 W:0
		012-048	Green+/Blue R:0 G:+ B:255 W:0
		049	Cyan R:0 G:255 B:255 W:0
		050-086	Green/Blue- R:0 G:255 B:- W:0
		087	Green R:0 G:255 B:0 W:0
		088-124	Red+/Green R:+ G:255 B:0 W:0
		125	Yellow R:255 G:255 B:0 W:0

		126-162	Red/Green- R:255 G:- B:0 W:0
		163	Red R:255 G:0 B:0 W:0
		164-200	Red/Blue+ R:255 G:0 B:+ W:0
		201	Magenta R:255 G:0 B:255 W:0
		202-238	Red-/Blue R:- G:0 B:255 W:0
		239	Blue R:0 G:0 B:255 W:0
		240-247	Colour index, fast to slow
		248-255	Colour snap, fast to slow
82	Plate foreground dimmer	000-255	0-100％
83	Plate background	000-000	No function
		001-002	White(2700K)
		003-004	White(3200K)
		005-006	White(4200K)
		007-008	White(5600K)
		009-010	White(8000K)
		011	Blue R:0 G:0 B:255 W:0
		012-048	Green+/Blue R:0 G:+ B:255 W:0
		049	Cyan R:0 G:255 B:255 W:0
		050-086	Green/Blue- R:0 G:255 B:- W:0
		087	Green R:0 G:255 B:0 W:0

		088-124	Red+/Green R:+ G:255 B:0 W:0
		125	Yellow R:255 G:255 B:0 W:0
		126-162	Red/Green- R:255 G:- B:0 W:0
		163	Red R:255 G:0 B:0 W:0
		164-200	Red/Blue+ R:255 G:0 B:+ W:0
		201	Magenta R:255 G:0 B:255 W:0
		202-238	Red-/Blue R:- G:0 B:255 W:0
		239	Blue R:0 G:0 B:255 W:0
		240-247	Color index,fast to slow
		248-255	Color snap,fast to slow
84	Plate background dimmer	000-255	0-100％
85	Plate 1(pixels 1-7)	000-002	Plate FX All select(all on) see Plate Patterns
85	FX select (see Pixel Mapping)	003-255	Plate FX All select(all on) see Plate Patterns
86	Plate 1(pixels 1-7) FX movement speed ＆ direction (see Pixel Mapping)	000-005	No function
		006-124	Left to right, fast to slow
		125-130	No function
		131-249	Right to left, slow to fast
		250-255	No function
87	Plate 1(pixels 1-7)	000-002	Snap from cell to cell
87	FX crossfade (see Pixel Mapping)	003-255	Fade duration: short to long
88	Plate 2(pixels 8-14)	000-002	Plate FX All select(all on) see Plate Patterns
88	FX select (see Pixel Mapping)	003-255	Plate FX All select(all on) see Plate Patterns
89	Plate 2(pixels 8-14)	000-005	No function

	FX movement speed ＆ direction (see Pixel Mapping)	006-124	Left to right, fast to slow
		125-130	No function
		131-249	Right to left, slow to fast
		250-255	No function
90	Plate 2(pixels 8-14)	000-002	Snap from cell to cell
90	FX crossfade (see Pixel Mapping)	003-255	Fade duration: short to long
91	Beam 1(pixels 1-14)	000-002	Beam FX All select(all on) see Beam Patterns
91	FX select (see Pixel Mapping)	003-255	Beam FX All select(all on) see Beam Patterns
92	Beam 1(pixels 1-14) FX movement speed ＆ direction (see Pixel Mapping)	000-005	No function
		006-124	Left to right, fast to slow
		125-130	No function
		131-249	Right to left, slow to fast
		250-255	No function
93	Beam 1(pixels 1-14)	000-002	Snap from cell to cell Fade duration: short to long
93	FX crossfade (see Pixel Mapping)	003-255	Snap from cell to cell Fade duration: short to long
94	Beam 2(pixels 15-28) FX select (see Pixel Mapping)	000-002	Beam FX All select(all on) see Beam Patterns
94		003-255	Beam FX All select(all on) see Beam Patterns
95	Beam 2(pixels 15-28)FX movement speed ＆ direction (see Pixel Mapping)	000-005	No function
		006-124	Left to right, fast to slow
		125-130	No function
		131-249	Right to left, slow to fast
		250-255	No function
96	Beam 2(pixels 15-28) FX crossfade (see Pixel Mapping)	000-002	Snap from cell to cell Fade duration: short to long
96		003-255	Snap from cell to cell Fade duration: short to long
97	Control*	000-005	No function
		006-010	Off (dimmer mode)
		011-015	Dimmer 1
		016-020	Dimmer 2
		021-025	Dimmer 3
		026-030	600 Hz
		031-035	1200 Hz
		036-040	2000 Hz
		041-045	4000 Hz
		046-050	6000 Hz
		051-055	25 KHz
		056-060	Fan mode auto
		060-065	Fan mode on
		066-070	Tilt reset

		071-075	Plate 1 invert off
		076-080	Plate 1 invert on
		081-085	Plate 2 invert off
		086-090	Plate 2 invert on
		091-095	Beam 1 invert off
		096-100	Beam 1 invert on
		101-105	Beam 2 invert off
		106-110	Beam 2 invert on
		111-115	Plate swap on
		116-120	Plate swap off
		121-125	Beam swap on
		126-130	Beam swap off
		131-255	No function

74CH
Channel	Function	Value	Percent/Setting
1	Tilt	000-255	0-100％
2	Fine tilt	000-255	0-100％
3	Dimmer	000-255	0-100％
4	Strobe	000-009	Open
		010-079	Strobe, slow to fast
		080-149	Pulse, slow to fast
		150-219	Random Strobe, slow to fast
		220-255	Open
5	Plate pixel 1 red	000-255	0-100％
6	Plate pixel 1 green	000-255	0-100％
7	Plate pixel 1 blue	000-255	0-100％
8	Plate pixel 2 red	000-255	0-100％
9	Plate pixel 2 green	000-255	0-100％
10	Plate pixel 2 blue	000-255	0-100％
11	Plate pixel 3 red	000-255	0-100％
12	Plate pixel 3 green	000-255	0-100％
13	Plate pixel 3 blue	000-255	0-100％
14	Plate pixel 4 red	000-255	0-100％
15	Plate pixel 4 green	000-255	0-100％
16	Plate pixel 4 blue	000-255	0-100％
17	Plate pixel 5 red	000-255	0-100％
18	Plate pixel 5 green	000-255	0-100％
19	Plate pixel 5 blue	000-255	0-100％
20	Plate pixel 6 red	000-255	0-100％
21	Plate pixel 6 green	000-255	0-100％
22	Plate pixel 6 blue	000-255	0-100％
23	Plate pixel 7 red	000-255	0-100％

24	Plate pixel 7 green	000-255	0-100％
25	Plate pixel 7 blue	000-255	0-100％
26	Plate pixel 8 red	000-255	0-100％
27	Plate pixel 8 green	000-255	0-100％
28	Plate pixel 8 blue	000-255	0-100％
29	Plate pixel 9 red	000-255	0-100％
30	Plate pixel 9 green	000-255	0-100％
31	Plate pixel 9 blue	000-255	0-100％
32	Plate pixel 10 red	000-255	0-100％
33	Plate pixel 10 green	000-255	0-100％
34	Plate pixel 10 blue	000-255	0-100％
35	Plate pixel 11 red	000-255	0-100％
36	Plate pixel 11 green	000-255	0-100％
37	Plate pixel 11 blue	000-255	0-100％
38	Plate pixel 12 red	000-255	0-100％
39	Plate pixel 12 green	000-255	0-100％
40	Plate pixel 12 blue	000-255	0-100％
41	Plate pixel 13red	000-255	0-100％
42	Plate pixel 13 green	000-255	0-100％
43	Plate pixel 13 blue	000-255	0-100％
44	Plate pixel 14 red	000-255	0-100％
45	Plate pixel 14 green	000-255	0-100％
46	Plate pixel 14 blue	000-255	0-100％
47	Beam pixel 1	000-255	0-100％
48	Beam pixel 2	000-255	0-100％
49	Beam pixel 3	000-255	0-100％
50	Beam pixel 4	000-255	0-100％
51	Beam pixel 5	000-255	0-100％
52	Beam pixel 6	000-255	0-100％
53	Beam pixel 7	000-255	0-100％
54	Beam pixel 8	000-255	0-100％
55	Beam pixel 9	000-255	0-100％
56	Beam pixel 10	000-255	0-100％
57	Beam pixel 11	000-255	0-100％
58	Beam pixel 12	000-255	0-100％
59	Beam pixel 13	000-255	0-100％
60	Beam pixel 14	000-255	0-100％
61	Beam pixel 15	000-255	0-100％
62	Beam pixel 16	000-255	0-100％
63	Beam pixel 17	000-255	0-100％
64	Beam pixel 18	000-255	0-100％
65	Beam pixel 19	000-255	0-100％
66	Beam pixel 20	000-255	0-100％

67	Beam pixel 21	000-255	0-100％
68	Beam pixel 22	000-255	0-100％
69	Beam pixel 23	000-255	0-100％
70	Beam pixel 24	000-255	0-100％
71	Beam pixel 25	000-255	0-100％
72	Beam pixel 26	000-255	0-100％
73	Beam pixel 27	000-255	0-100％
74	Beam pixel 28	000-255	0-100％

30CH
Channel	Function	Value	Percent/Setting
1	Tilt	000-255	0-100％
2	Fine tilt	000-255	0-100％
3	Master dimmer	000-255	0-100％
4	Plate dimmer	000-255	0-100％
5	Beam dimmer	000-255	0-100％
6	Plate flash duration	000-009	Classic shutter mode: disables duration control
		010-250	Slow to fast
		251-255	100％On, no flash/strobe
7	Plate flash rate	000-009	100%
		010-250	Slow to fast
		251-255	100%
8	Beam flash duration	000-009	Classic shutter mode: disables duration control
		010-250	Slow to fast
		251-255	100％On, no flash/strobe
9	Beam flash rate	000-009	100%
		010-250	Slow to fast
		251-255	100%
10	Plates red	000-255	0-100％
11	Plates green	000-255	0-100％
12	Plates blue	000-255	0-100％
13	Beam FX	000-005	No function
		006-042	Ramp up
		043-085	Ramp down
		086-128	Ramp up-down
		129-171	Random
		172-214	Lightning
		215-255	Spikes
14	Plates foreground	000-000	No function

		001-002	White(2700K)
		003-004	White(3200K)
		005-006	White(4200K)
		007-008	White(5600K)
		009-010	White(8000K)
		011	Blue R:0 G:0 B:255 W:0
		012-048	Green+/Blue R:0 G:+ B:255 W:0
		049	Cyan R:0 G:255 B:255 W:0
		050-086	Green/Blue- R:0 G:255 B:- W:0
		087	Green R:0 G:255 B:0 W:0
		088-124	Red+/Green R:+ G:255 B:0 W:0
		125	Yellow R:255 G:255 B:0 W:0
		126-162	Red/Green- R:255 G:- B:0 W:0
		163	Red R:255 G:0 B:0 W:0
		164-200	Red/Blue+ R:255 G:0 B:+ W:0
		201	Magenta R:255 G:0 B:255 W:0
		202-238	Red-/Blue R:- G:0 B:255 W:0
		239	Blue R:0 G:0 B:255 W:0

		240-247	Colour index, fast to slow
		248-255	Colour snap, fast to slow
15	Plates foreground dimmer	000-255	0-100％
16	Plates background	000-000	No function
		001-002	White(2700K)
		003-004	White(3200K)
		005-006	White(4200K)
		007-008	White(5600K)
		009-010	White(8000K)
		011	Blue R:0 G:0 B:255 W:0
		012-048	Green+/Blue R:0 G:+ B:255 W:0
		049	Cyan R:0 G:255 B:255 W:0
		050-086	Green/Blue- R:0 G:255 B:- W:0
		087	Green R:0 G:255 B:0 W:0
		088-124	Red+/Green R:+ G:255 B:0 W:0
		125	Yellow R:255 G:255 B:0 W:0
		126-162	Red/Green- R:255 G:- B:0 W:0
		163	Red R:255 G:0 B:0 W:0
		164-200	Red/Blue+ R:255 G:0 B:+ W:0
		201	Magenta R:255 G:0 B:255 W:0

		202-238	Red-/Blue R:- G:0 B:255 W:0
		239	Blue R:0 G:0 B:255 W:0
		240-247	Colour index, fast to slow
		248-255	Colour snap, fast to slow
17	Plates background dimmer	000-255	0-100％
18	Plate 1(pixels 1-7)	000-002	Plate FX All select(all on) see Plate Patterns
18	FX select (see Pixel Mapping)	003-255	Plate FX All select(all on) see Plate Patterns
19	Plate 1(pixels 1-7) FX movement speed ＆ direction (see Pixel Mapping)	000-005	No function
		006-124	Left to right, fast to slow
		125-130	No function
		131-249	Right to left, slow to fast
		250-255	No function
20	Plate 1(pixels 1-7)	000-002	Snap from cell to cell
20	FX crossfade (see Pixel Mapping)	003-255	Fade duration:short to long
21	Plate 2(pixels 8-14)	000-002	Plate FX All select(all on) see Plate Patterns
21	FX select (see Pixel Mapping)	003-255	Plate FX All select(all on) see Plate Patterns
22	Plate 2(pixels 8-14) FX movement speed ＆ direction (see Pixel Mapping)	000-005	No function
		006-124	Left to right, fast to slow
		125-130	No function
		131-249	Right to left,slow to fast
		250-255	No function
23	Plate 2(pixels 8-14)	000-002	Snap from cell to cell
23	FX crossfade (see Pixel Mapping)	003-255	Fade duration:short to long
24	Beam 1(pixels 1-14)	000-002	Beam FX All select(all on) see Beam Patterns
24	FX select (see Pixel Mapping)	003-255	Beam FX All select(all on) see Beam Patterns
25	Beam 1(pixels 1-14) FX movement speed ＆ direction (see Pixel Mapping)	000-005	No function
		006-124	Left to right,fast to slow
		125-130	No function
		131-249	Right to left, slow to fast
		250-255	No function
26	Beam 1(pixels 1-14)	000-002	Snap from cell to cell Fade duration: short to long
26	FX crossfade (see Pixel Mapping)	003-255	Snap from cell to cell Fade duration: short to long

27	Beam 2(pixels 15-28) FX select (see Pixel Mapping)	000-002	Beam FX All select(all on) see Beam Patterns
27		003-255	Beam FX All select(all on) see Beam Patterns
28	Beam 2(pixels 15-28)FX movement speed ＆ direction (see Pixel Mapping)	000-005	No function
		006-124	Left to right, fast to slow
		125-130	No function
		131-249	Right to left, slow to fast
		250-255	No function
29	Beam 2(pixels 15-28) FX crossfade (see Pixel Mapping)	000-002	Snap from cell to cell Fade duration:short to long
29		003-255	Snap from cell to cell Fade duration:short to long
30	Control*	000-005	No function
		006-010	Off (dimmer mode)
		011-015	Dimmer 1
		016-020	Dimmer 2
		021-025	Dimmer 3
		026-030	600 Hz
		031-035	1200 Hz
		036-040	2000 Hz
		041-045	4000 Hz
		046-050	6000 Hz
		051-055	25 KHz
		056-060	Fan mode auto
		060-065	Fan mode on
		066-070	Tilt reset
		071-075	Plate 1 invert off
		076-080	Plate 1 invert on
		081-085	Plate 2 invert off
		086-090	Plate 2 invert on
		091-095	Beam 1 invert off
		096-100	Beam 1 invert on
		101-105	Beam 2 invert off
		106-110	Beam 2 invert on
		111-115	Plate swap on
		116-120	Plate swap off
		121-125	Beam swap on
		126-130	Beam swap off
		131-255	No function

24CH
Channel	Function	Value	Percent/Setting
1	Tilt	000-255	0-100％
2	Fine tilt	000-255	0-100％

3	Master dimmer	000-255	0-100％
4	Plate dimmer	000-255	0-100％
5	Beam dimmer	000-255	0-100％
6	Plate flash duration	000-009	Classic shutter mode:disables duration control
		010-250	Slow to fast
		251-255	100％On,no flash/strobe
7	Plate flash rate	000-009	100%
		010-250	Slow to fast
		251-255	100%
8	Beam flash duration	000-009	Classic shutter mode:disables duration control
		010-250	Slow to fast
		251-255	100％On,no flash/strobe
9	Beam flash rate	000-009	100%
		010-250	Slow to fast
		251-255	100%
10	Plates red	000-255	0-100％
11	Plates green	000-255	0-100％
12	Plates blue	000-255	0-100％
13	Beam FX	000-005	No function
		006-042	Ramp up
		043-085	Ramp down
		086-128	Ramp up-down
		129-171	Random
		172-214	Lightning
		215-255	Spikes
14	Plates foreground	000-000	No function
		001-002	White(2700K)
		003-004	White(3200K)
		005-006	White(4200K)
		007-008	White(5600K)
		009-010	White(8000K)
		011	Blue R:0 G:0 B:255 W:0
		012-048	Green+/Blue R:0 G:+ B:255 W:0
		049	Cyan R:0 G:255 B:255

			W:0
		050-086	Green/Blue- R:0 G:255 B:- W:0
		087	Green R:0 G:255 B:0 W:0
		088-124	Red+/Green R:+ G:255 B:0 W:0
		125	Yellow R:255 G:255 B:0 W:0
		126-162	Red/Green- R:255 G:- B:0 W:0
		163	Red R:255 G:0 B:0 W:0
		164-200	Red/Blue+ R:255 G:0 B:+ W:0
		201	Magenta R:255 G:0 B:255 W:0
		202-238	Red-/Blue R:- G:0 B:255 W:0
		239	Blue R:0 G:0 B:255 W:0
		240-247	Color index,fast to slow
		248-255	Color snap,fast to slow
15	Plates foreground dimmer	000-255	0-100％
16	Plates background	000-000	No function
		001-002	White(2700K)
		003-004	White(3200K)
		005-006	White(4200K)
		007-008	White(5600K)
		009-010	White(8000K)
		011	Blue R:0 G:0 B:255

			W:0
		012-048	Green+/Blue R:0 G:+ B:255 W:0
		049	Cyan R:0 G:255 B:255 W:0
		050-086	Green/Blue- R:0 G:255 B:- W:0
		087	Green R:0 G:255 B:0 W:0
		088-124	Red+/Green R:+ G:255 B:0 W:0
		125	Yellow R:255 G:255 B:0 W:0
		126-162	Red/Green- R:255 G:- B:0 W:0
		163	Red R:255 G:0 B:0 W:0
		164-200	Red/Blue+ R:255 G:0 B:+ W:0
		201	Magenta R:255 G:0 B:255 W:0
		202-238	Red-/Blue R:- G:0 B:255 W:0
		239	Blue R:0 G:0 B:255 W:0
		240-247	Color index,fast to slow
		248-255	Color snap,fast to slow
17	Plates background dimmer	000-255	0-100％
18	Plates 1＆2	000-002	Plate FX All select(all on)

	FX select (see Pixel Mapping)	003-255	see Plate Patterns
19	Plates 1＆2 FX movement speed ＆ direction (see Pixel Mapping)	000-005	No function
		006-124	Left to right,fast to slow
		125-130	No function
		131-249	Right to left,slow to fast
		250-255	No function
20	Plates 1＆2	000-002	Snap from cell to cell
20	FX crossfade (see Pixel Mapping)	003-255	Fade duration:short to long
21	Beams 1＆2	000-002	Beam FX All select(all on) see Beam Patterns
21	FX select (see Pixel Mapping)	003-255	Beam FX All select(all on) see Beam Patterns
22	Beams 1＆2 FX movement speed ＆ direction (see Pixel Mapping)	000-005	No function
		006-124	Left to right,fast to slow
		125-130	No function
		131-249	Right to left,slow to fast
		250-255	No function
23	Beams 1＆2	000-002	Snap from cell to cell Fade duration:short to long
23	FX crossfade (see Pixel Mapping)	003-255	Snap from cell to cell Fade duration:short to long
24	Control*	000-005	No function
		006-010	Off (dimmer mode)
		011-015	Dimmer 1
		016-020	Dimmer 2
		021-025	Dimmer 3
		026-030	600 Hz
		031-035	1200 Hz
		036-040	2000 Hz
		041-045	4000 Hz
		046-050	6000 Hz
		051-055	25 KHz
		056-060	Fan mode auto
		060-065	Fan mode on
		066-070	Tilt reset
		071-075	Plate 1 invert off
		076-080	Plate 1 invert on
		081-085	Plate 2 invert off
		086-090	Plate 2 invert on
		091-095	Beam 1 invert off
		096-100	Beam 1 invert on
		101-105	Beam 2 invert off
		106-110	Beam 2 invert on

		111-115	Plate swap on
		116-120	Plate swap off
		121-125	Beam swap on
		126-130	Beam swap off
		131-255	No function

13CH
Channel	Function	Value	Percent/Setting
1	Tilt	000-255	0-100％
2	Fine tilt	000-255	0-100％
3	Plate dimmer	000-255	0-100％
4	Beam dimmer	000-255	0-100％
5	Plate flash duration	000-009	Classic shutter mode: disables duration control
		010-250	Slow to fast
		251-255	100％On, no flash/strobe
6	Plate flash rate	000-009	100%
		010-250	Slow to fast
		251-255	100%
7	Beam flash duration	000-009	Classic shutter mode: disables duration control
		010-250	Slow to fast
		251-255	100％On, no flash/strobe
8	Beam flash rate	000-009	100%
		010-250	Slow to fast
		251-255	100%
9	Plates red	000-255	0-100％
10	Plates green	000-255	0-100％
11	Plates blue	000-255	0-100％
12	Beam FX	000-005	No function
		006-042	Ramp up
		043-085	Ramp down
		086-128	Ramp up-down
		129-171	Random
		172-214	Lightning
		215-255	Spikes
13	Control*	000-005	No function
		006-010	Off (dimmer mode)
		011-015	Dimmer 1
		016-020	Dimmer 2
		021-025	Dimmer 3

		026-030	600 Hz
		031-035	1200 Hz
		036-040	2000 Hz
		041-045	4000 Hz
		046-050	6000 Hz
		051-055	25 KHz
		056-060	Fan mode auto
		060-065	Fan mode on
		066-070	Tilt reset
		071-075	Plate 1 invert off
		076-080	Plate 1 invert on
		081-085	Plate 2 invert off
		086-090	Plate 2 invert on
		091-095	Beam 1 invert off
		096-100	Beam 1 invert on
		101-105	Beam 2 invert off
		106-110	Beam 2 invert on
		111-115	Plate swap on
		116-120	Plate swap off
		121-125	Beam swap on
		126-130	Beam swap off
		131-255	No function

11CH
Channel	Function	Value	Percent/Setting
1	Tilt	000-255	0-100％
2	Fine tilt	000-255	0-100％
3	Dimmer	000-255	0-100％
4	Plate flash duration	000-009	Classic shutter mode:disables duration control
		010-250	Slow to fast
		251-255	100％On,no flash/strobe
5	Plate flash rate	000-009	100%
		010-250	Slow to fast
		251-255	100%
6	Beam flash duration	000-009	Classic shutter mode:disables duration control
		010-250	Slow to fast
		251-255	100％On,no flash/strobe
7	Beam flash rate	000-009	100%
7	Beam flash rate	010-250	Slow to fast

		251-255	100%
8	Plates red	000-255	0-100％
9	Plates green	000-255	0-100％
10	Plates blue	000-255	0-100％
11	Beam	000-255	0-100％

8CH
Channel	Function	Value	Percent/Setting
1	Tilt	000-255	0-100％
2	Fine tilt	000-255	0-100％
3	Dimmer	000-255	0-100％
4	Strobe	000-009	Open
		010-079	Strobe,slow to fast
		080-149	Pulse,slow to fast
		150-219	Random Strobe,slow to fast
		220-255	Open
5	Red	000-255	0-100％
6	Green	000-255	0-100％
7	Blue	000-255	0-100％
8	Beam	000-255	0-100％

Troubleshooting

Symptom	cause of issue	Approach
No menu displayed	1. No AC input 2. The switching power supply is damaged 3. Display board failure	1. Check the power supply line 2. Check whether the switching power supply has voltage output 3. Replace the display board
Can’t receive DMX signal	1. The DMX signal line is faulty 2. The wiring sequence of the signal line is wrong 3. The IC receiving the signal at the signal input terminal is damaged 4. DMX address code setting and console Corresponding controls do not match 5. Other parameters are set incorrectly 6. After entering the menu without pressing the confirm button or MENU key to exit to the main menu	1. Check or replace the signal line 2. Check the wiring sequence of the signal lines 3. Check the display board signal receiving IC and Are the two resistors connected in series on the signal line open? 4. Check or reset the address code Or restore factory settings and try again 5. Press MENU to exit to the main menu
The surface temperature of the lamp body exceeds 75° No temperature control protection	1. The thermistor on the lamp bead board is faulty 2. The temperature control circuit on the display board is faulty	1. Replace the thermistor 2. Check the temperature control circuit on the motherboard
Uneven colour mixing Uneven colour spots	1. Improper soldering of lamp beads 2. The lens or bracket is not installed properly	1. Check the bulb welding condition 2. Check the lens assembly process and adjust the bracket assembly direction
The lamp bead is off or flickering a little	The lamp bead is damaged or the driver board has no current output	1. Replace the lamp bead 2. Replace the damaged lamp beads Or check the driver board circuit 3. Replace the corresponding driver IC
Parameters are not saved	Damaged IC for storing parameters	Replace memory IC
The whole light does not work	When the temperature is too high, the temperature control protection will cause Switching the power supply over-temperature protection does not work	Wait for the lamp body to cool down before turning it on

Documents / Resources

AVTech SATURN700RGB 700W Power LED Tilt Moving Strobe [pdf] User Manual
SATURN700RGB 700W Power LED Tilt Moving Strobe, 700W Power LED Tilt Moving Strobe, LED Tilt Moving Strobe, Tilt Moving Strobe, Moving Strobe, Strobe

References

User Manual

AVTech SATURN700RGB 700W Power LED Tilt Moving Strobe

Product Usage Instructions

FAQ