AUTOOL RE110 Remote Key Frequency Tester
COPYRIGHT INFORMATION
Copyright
- All rights reserved by AUTOOL TECH. CO., LTD. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of AUTOOL. The information contained herein is designed only for the use of this unit. AUTOOL is not responsible for any use of this information as applied to other units.
- Neither AUTOOL nor its affiliates shall be liable to the purchaser of this unit or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this unit, or unauthorized modifications, repairs, or alterations to this unit, or failure to strictly comply with AUTOOL operating and maintenance instructions.
- AUTOOL shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as original AUTOOL products or AUTOOL-approved products by AUTOOL.
- Other product names used herein are for identification purposes only and may be trademarks of their respective owners. AUTOOL disclaims any and all rights in those marks.
Trademark
Manual are either trademarks, registered trademarks, service marks, domain names, logos, company names or are otherwise the property of AUTOOL or its affiliates. In countries where any of the AUTOOL trademarks, service marks, domain names, logos and company names are not registered, AUTOOL claims other rights associated with unregistered trademarks, service marks, domain names, logos, and company names. Other products or company names referred to in this manual may be trademarks of their respective owners. You may not use any trademark, service mark, domain name, logo, or company name of AUTOOL or any third party without permission from the owner of the applicable trademark, service mark, domain name, logo, or company name. You may contact AUTOOL by visiting AUTOOL at https://www.autooltech.com, or writing to aftersale@autooltech.com, to request written permission to use materials on this manual for purposes or for all other questions relating to this manual.
SAFETY RULES
General safety rules
- Always keep this user manual with the machine.
- Before using this product, read all the operational instructions in this manual. Failure to follow them may result in electric shock and irritation to skin and eyes.
- Each user is responsible for installing and using the device according to this user manual. The supplier is not responsible for damage caused by improper use and operation.
- This device must only be operated by trained and qualified personnel. Do not operate it under the influence of drugs, alcohol, or medication.
- This machine is developed for specific applications. The supplier points out that any modification and/or use for any unintended purposes is strictly prohibited.
- The supplier assumes no express or implied warranties or liabilities for personal injury or property damage caused by improper use, misuse, or failure to follow safety instructions.
- This device is intended for use by professionals only. Improper use by non-professionals may result in injury or damage to the tools or workpieces.
- Keep out of reach of children.
- When operating, ensure nearby personnel or animals maintain a safe distance. Avoid working in rain, water, or damp environments. Keep the work area well-ventilated, dry, clean, and bright.
Handling
- Used/damaged device must not be disposed of in household waste but must be disposed of in an environmentally friendly manner. Use designated electrical device collection points.
- Used batteries should be treated as hazardous waste, such as at a designated waste disposal facility.
Electrical safety rules
If the device has not been used for a long time or if the battery is depleted, it may not power on properly. This is a normal occurrence. Please replace the battery first and then try turning on the device again.
Equipment safety rules’
- Do not leave the device unattended while it is running. Always turn off the device at the main switch when it is not being used for its intended purpose!
- Do not attempt to repair the device yourself.
- Before connecting the device to power, check whether the voltage of the power supply battery matches the rated parameters. If not, it may cause serious hazards and damage the device.
- It is essential to protect the device from rainwater, moisture, mechanical damage, overload, and rough handling.
Application
- Before use, check whether the indicator light, battery clamps, and detection probe are damaged. If any damage is found, do not operate the device.
- Use the device only in compliance with all safety instructions, technical documents, and vehicle manufacturer specifications.
- If the power supply battery needs to be replaced, use only a brand-new, unopened corresponding product.
Personnel protection safety rules
- Do not connect live conductors in a damp environment.
- Before using the product, inspect the casing for any cracks or damage to plastic parts. Pay special attention to the insulation near the ports.
- Always ensure you have a stable footing to safely control device in case of emergencies.
Any other use is considered to exceed the intended purpose of the equipment and is prohibited.
CAUTIONS
- Do not disassemble or modify the equipment without authorization.
- Avoid electronic signal interference sources during testing, such as signal towers, base stations, utility poles, making phone calls, sending or receiving text messages, etc.
- Before testing, check if the equipment is malfunctioning to ensure it is working properly to avoid injury.
- Before installation and debugging, read this manual carefully. If you have any questions, contact the dealer or the AUTOOL company immediately.
PRODUCT INTRODUCTION
This is an instrument for testing the frequency of wireless remote controls. It can measure the frequency of the remote control and display the value. Additionally, it can test the functionality of infrared sensors and supports testing of button batteries.
Technical Specifications
| Operating Voltage | 4*1.5V AAA batteries |
| TYPE-C Operating Power Supply | 5V/1A |
| Detection Frequency Bands | 315MHz, 433MHz,
868MHz, 902MHz |
| Battery Measurement Voltage Range | 0~6V |
| Supported Battery Models for Detection | CR2032, CR2025 |
| Operating Temperature | -10°C~60°C |
| Storage Temperature | -20°C~65°C |
PRODUCT STRUCTURE
Structural Diagram
| A | Battery Testing Area |
| B | Infrared Receiver |
| C | Display Screen |
| D | Mode Switch Button |
| E | Key Testing Area |
| F | Type-C Power Interface |
| G | Power On/Off Switch |
OPERATING INSTRUCTIONS
Basic Operation Procedure
Place the car remote key that needs to be tested near the key testing area, and press the button on the remote key. This will allow you to test the frequency of the key, and clearly display the frequency value.
The frequency bands of car remote keys that can be tested are mainly: 315MHz, 433MHz, 868MHz, and 902MHz.
NOTE
It is recommended to test closer to the testing area to ensure more accurate measurement values! If the test value cannot be displayed normally, the frequency of the remote key may not be suitable for this device!
Mode Switching
Key Frequency Detection Mode (RF)
Long press the [
] power switch for 2 seconds to power on and enter the frequency detection mode. Place the key near the key testing area, press the key button to test the frequency of the key, and the screen will display the frequency value. (Press the [ ] power switch to clear the current test frequency).
Battery Testing Mode (BAT)
Press the [ 
] mode switch button to enter the battery testing mode (BAT). Insert the battery to be tested into the battery testing area, and the screen will display the battery voltage.
NOTE
Pay attention to the positive and negative polarity markings on the battery.
Infrared Testing Mode (IR)
Press the [ ] mode switch button to enter the infrared testing mode (IR). Point the infrared remote controller to this product and press the button to test. The screen will display OK.
NOTE
If there is no display on the screen, it means the infrared transmitter of the remote controller is malfunctioning!
MAINTENANCE SERVICE
Our products are made of long-lasting and durable materials, and we insist on perfect production process. Each product leaves the factory after 35 procedures and 12 times of testing and inspection work, which ensures that each product has excellent quality and performance.
Maintenance
To maintain the performance and appearance of the product, it is recommended that the following product care guidelines be read carefully：
- Be careful not to rub the product against rough surfaces or wear the product, especially the sheet metal housing.
- Please regularly check the product parts that need to be tightened and connected. If found loose, please tighten it in time to ensure the safe operation of the equipment. The external and internal parts of the equipment in contact with various chemical media should be frequently treated with anti-corrosion treatment such as rust removal and painting to improve the corrosion resistance of the equipment and extend its service life.
- Comply with the safe operating procedures and do not overload the equipment. The safety guards of the products are complete and reliable.
- Unsafe factors are to be eliminated in time. The circuit part should be checked thoroughly and the aging wires should be replaced in time.
- When not in use, please store the product in a dry place. Do not store the product in hot, humid, or non-ventilated places.
WARRANTY
From the date of receipt, we provide a three-year warranty for the main unit and all the accessories included are covered by a one-year warranty.
Warranty access
- The repair or replacement of products is determined by the actual breakdown situation of the product.
- It is guaranteed that AUTOOL will use brand new component, accessory or device in terms of repair or replacement.
- If the product fails within 90 days after the customer receives it, the buyer should provide both video and picture, and we will bear the shipping cost and provide the accessories for the customer to replace it free of charge. While the product is received for more than 90 days, the customer will bear the appropriate cost and we will provide the parts to the customer for replacement free of charge.
The conditions below shall not be in the warranty range
The product is not purchased through official or authorized channels.
The product breakdown because the user does not follow the product instructions to use or maintain the product.
We at AUTOOL pride ourselves on superb design and excellent service. It would be our pleasure to provide you with any further support or services.
Disclaimer
All information, illustrations, and specifications contained in this manual, AUTOOL resumes the right of modify this manual and the machine itself with no prior notice. The physical appearance and color may differ from what is shown in the manual, please refer to the actual product.
Every effort has been made to make all descriptions in the book accurate, but inevitably, there are still inaccuracies. if in doubt, please contact your dealer or AUTOOL after-ser-vice centre; we are not responsible for any consequences arising from misunderstandings.
RETURN & EXCHANGE SERVICE
Return & Exchange
- If you are an AUTOOL user and are not satisfied with the AUTOOL products purchased from the online authorize shopping platform and offline authorized dealers, you can return the products within seven days from the date of receipt; or you may exchange it for another product of the same value within 30 days from the date of delivery.
- Returned and exchanged products must be in fully saleable condition with documentation of the relevant bill of sale, all relevant accessories and original packaging.
- AUTOOL will inspect the returned items to ensure that they are in good condition and eligible. Any item that does not pass inspection will be returned to you and you will not receive a refund for the item.
- You can exchange the product through the customer service center or AUTOOL authorized distributors; the policy of return and exchange is to return the product from where it was purchased. If there are difficulties or problems with your return or exchange, please contact AUTOOL Customer Service.
| China | 400-032-0988 |
| Oversea Zone | +86 0755 23304822 |
| aftersale@autooltech.com | |
| https://www.facebook.com/autool.vip | |
| YouTube | https://www.youtube.com/c/autooltech |
EU DECLARATION OF CONFORMITY
We as the manufacturer declare that the designated product:
Description: Remote Key Frequency Tester (RE110) complies with the requirements of the:
EMC Directive 2014/30/EU
RoHS Directive 2011/65/EU + 2015/863 + 2017/2102 Applied Standards:
EN IEC 55014-1:2021, EN IEC 61000-3-2:2019+A1:2021, EN 61000-3-3:2013+A2:2021, EN IEC 55014-2:2021 EC 62321-3-1:2013, IEC 62321-7-1:2015, IEC
62321-4:2013+A1:2017, IEC 62321-7-2:2017, IEC 62321-5:2013, IEC 62321-6:2015, IEC 62321-8:2017 Certificate No.: HS202408077210E, HS202408077213E Test Report No.: HS202408077210-1ER, HS202408077213-1ER
|
Manufacturer |
Shenzhen AUTOOL Technology Co, Ltd. |
| Floor 2, Workshop 2, Hezhou Anle Industrial Park, Hezhou Community, Hangcheng Street, Bao’an ‘District, Shenzhen
Email: aftersale@autooltech.com |
|
 |
COMPANY NAME: XDH Tech |
| ADRESS: 2 Rue Coysevox Bureau 3, Lyon, France
E-MaiL: xdh.tech@outlook.com CONTACT PERSON: Dinghao Xue |
AUTOOL TECHNOLOGY CO.,LTD
www.autooltech.com
aftersale@autooltech.com
+86-755-2330 4822 / +86-400 032 0988
HangcUnit 1303, Building 1, Runzhi R&D Center, Bao’an, Shenzhen, China
Execution Standard: GB/T 12548-2016
Documents / Resources
 |
AUTOOL RE110 Remote Key Frequency Tester [pdf] User Manual RE110, ND300, RE110 Remote Key Frequency Tester, RE110, Remote Key Frequency Tester, Key Frequency Tester, Frequency Tester |
