LAUNCH TSENSOR-05N Universal Tpms Sensor User Guide

LAUNCH TSENSOR-05N Universal Tpms Sensor

Technical Specifications

• Dimensions 74.39 mm*27.04mm*19mm
• Weight 35g
• IP Rating IP6K9K
• Operating Temperature -40℃ ~ 120℃
• Storage Temperature -40℃ ~ 120℃

IMPORTANT: Read, understand and follow all safety messages and instructions in this manual before operating or maintaining this unit. Use this unit correctly and with care. Failure to do so may cause damage and/or personal injury and will void the product warranty.

Safety Instructions

Any maintenance and repair work must be carried out by trained technicians. Failure to do so may result in the failure of the TPMS sensor. LAUNCH does not assume any liability in case of faulty or incorrect installation of the unit.

CAUTION

• When mounting/dismounting the wheel, follow the operation guideline of the wheel changer manufacturer strictly.
• Do not race with the vehicle on which the sensor is mounted, and always keep the driving speed under 240km/h.
• To guarantee optimal performance, the sensor shall only be installed with the original accessories provided by LAUNCH.
•  If the sensor is damaged on the outer surface, it must be replaced with a new one, and the specified sensor torque is 4 N·m.
•  Make sure to program the sensors by using the LAUNCH-specific TPMS tool prior to installation.
• Do not install programmed TPMS sensors in damaged wheels.
•  After installing the TPMS sensor, test the vehicle’s Tire Pressure Monitoring System following the steps described in the original manufacturer’s user manual to confirm proper installation.

Components & Controls

Installation Steps

Loosening the tire

• Remove the valve cap and nut, and deflate the tire. Use the bead loosener to break the tire bead.
• Caution: The bead loosener must be facing the valve.

Dismounting the tire
Clamp the tire on the tire changer, and adjust the valve at 1 o’clock to the tire fitting head. Use the tire tool to dismount the tire bead.

Dismounting the sensor
Remove the cap and nut from the valve stem, and then remove the sensor assembly from the wheel rim.

Mounting the sensor and valve

• Step 1. Remove the cap and nut from the valve stem.
• Step 2. Place the valve stem through the valve hole of the rim, ensuring the sensor body located on the inside of the rim. Assemble the nut back on the valve stem with a torque of 4N·m, then tighten the cap.

Remounting the tire
Place the tire on the rim, ensure that the valve starts on the opposite side of the rim from the tire fitting head. Mount the tire over the rim.

Warranty

The sensor is guaranteed to be free from material and manufacturing defects for a period of twenty-four (24) months or for 31000 miles, whichever comes first. This warranty covers any defects in materials or workmanship under normal use during the warranty period. Excluded from the warranty are defects due to improper installation and usage, induction of defect by other products, damage due to collision or tire failure.

Manufacturer Information

• Manufacturer: LAUNCH TECH CO., LTD. Address: No.4012, Launch Industrial Park, North
• Wuhe Rd, Bantian Street, Longgang District, Shenzhen, China
• Website: https://en.cnlaunch.com
• Phone: +86 755 8455 7891
• Email: overseas.service@cnlaunch.com

Compliance Information

• FCC ID: XUJTSENN
• IC: 29886-TSENN
• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Innovation, Science and Economic Development Canada’s licence-exempt RSSs and part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference; and
2. This device must accept any interference received, including interference that may cause undesired operation..

This Class B digital apparatus complies with Canadian ICES-003.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU. The RF frequencies can be used in Europe without restriction.

Disclaimer

•  All information, illustrations, and specifications in this quick start guide are based on the latest information available at the time of publication.
•  The right is reserved to make changes at any time without notice. LAUNCH shall not be liable for any direct, special, incidental, indirect damages or any economic consequential damages (including the loss of profits) due to the use of the document.