Laser 8945 Engine Timing Kit

Product Information
- Part No.: 8945
- Product: Engine Timing Kit
- Compatibility: 1.0 Wet Belt Non-Turbo Ford Petrol
- Manufacturer: Laser Tools
- Design: UK REGISTERED DESIGN
- Website: www.lasertools.co.uk
Product Usage Instructions
Flywheel Holding Tool
- Used to lock the flywheel when loosening and tightening the crankshaft pulley bolt.
Crankshaft Timing Pin
- Used to set the crankshaft position by turning it clockwise until it contacts the pin.
Tensioner Pulley Locking Pin
- Locks the belt tensioner in its fully retracted position.
Crankshaft Pulley Alignment Pin
- Initial position setter for the crankshaft. Remove pin D before torqueing or loosening the crankshaft pulley bolt.
4mm Tensioner Pin
- Locks the auxiliary belt tensioner in its retracted position.
Camshaft Timing Tools & Fixings
- Used to lock the camshafts in their timed position independently of their pulleys. Ensure proper assembly over the camshafts and tighten fixing bolts hand tight.
Front Cover Oil Seal Installer
- Used to fit the new front crankshaft oil seal into the front cover after re-fitting it to the engine. Follow manufacturers tightening sequence and torques for front cover bolts.
Description
- Designed specifically for the 1.0 litre 3 cylinder normally aspirated petrol engine from Ford, the 7828 kit provides all the tools required to set the engine timing. Our specially designed cam locking bridges offer an easy to use and more positive method of locking the camshaft than even the OEM tools can offer, ensuring the camshafts are securely locked in position quickly and easily.
- Applications include: Ford Fiesta (from 2013) 1.0lt Non-Turbo petrol engine codes: P4JA, P4JB, P4JC, P4JD, XMJA, XMJB, XMJC, XMJD and XTCA.
- For setting of the Variable Camshaft Timing (VCT) units, please use Laser Part No. 6291.
For Ecoboost Turbo 1.0L engine timing, please see Laser Part No. 6952 (if you already own the Laser timing tool Part No. 6952, the camshaft locking blocks for 1.0L non-turbo are available to buy separately, under part no. 8946).
Use with Laser 7318 and 6291.
- NOTE*= for 1.0 non-turbo engine only.
- The information given below is for reference only. Laser Tools recommends the use of Manufacturer data or Autodata. Laser Tools cannot be held responsible for damage to engine or personnel whilst using this tool kit.
Applications
| Make | Model | Year |
| Ford | Fiesta | 2013 to 2017 |

| Engine Codes |
| 1.0LT |
| P4JA |
| P4JB |
| P4JC |
| P4JD |
| XMJA |
| XMJB |
| XMJC |
| XMJD |
| XTCA |
| Item | Comp. No. | Description | OEM. |
| A | C701 | Flywheel Holding Tool | 303-1602 |
| B | C702 | Crankshaft Timing Pin | 303-1604 |
| C | C282 | Tensioner Pulley Locking Pin | 303-1054 |
| D | C089 | Crankshaft Pulley Alignment Pin | 303-732 |
| E | C488 | 4mm Tensioner Pin | 4MM PIN |
| F | C1070 | Camshaft Timing Tools & Fixings | 303-1605* |
| G | C705 | Front Cover Oil Seal Installer | 303-1603 |
Instructions for use
- Always refer to manufacturer-specific data and instructions.
- N.B. the camshaft drive belt on the Ford 3 Cylinder 1.0lt engine is “oil bathed”.
- The front engine casing must be removed to gain access.
- Turn engine to TDC number one before disassembly of engine.
- Remove the starter motor and use component A to hold the flywheel when undoing the crankshaft pulley bolt.

Component A:
- Used to lock the flywheel when loosening and tightening the crankshaft pulley bolt. Remove the starter motor, assemble component A as shown, and fit in the starter aperture so that its tooth locks the flywheel (see opposite):
Component B:
- Used to set the crankshaft position. Remove the blanking plug in the side of the engine block as shown and fit component B; turn the crankshaft slowly clockwise until the crankshaft web contacts the end of component B.
Component C:
- Used to lock the belt tensioner in its fully retracted position, as shown.
Component D:
- Used to initially set the position of the crankshaft via a hole in the front crankshaft pulley as shown in figure 3.
- NOTE: Remove pin D in place when torqueing or loosening the crankshaft pulley bolt.
Component E:
- Used to lock the auxiliary belt tensioner in its retracted position.
Component F:
- Used to lock the camshafts in their timed position independently of their pulleys. With component B already fitted and the engine at TDC cylinder number 1, assemble the components for F as shown below
- Install the assembled camshaft components F over the square section of the camshafts ensuring the holding tools seat on the surface of the cylinder head. Fit fixing bolts hand tight

- N.B. On engines equipped with VCT, if the VCT pulleys require removal or loosening ensure their initial position is marked with chalk or paint. Additional tooling will be required to set the position of the VCT pulleys, see Laser 6291.
Component G:
- This is used to fit the new front crankshaft oil seal into the front cover after the front cover has been refitted to the engine.
N.B. Always observe the manufacturer’s tightening sequence and torques for the front cover bolts.
- Our products are designed to be used correctly and with care for the purpose for which they are intended. No liability is accepted by the Tool Connection for incorrect use of any of our products, and the Tool Connection cannot be held responsible for any damage to personnel, property or equipment when using the tools. Incorrect use will also invalidate the warranty.
- If applicable, the applications database and any instructional information provided has been designed to offer general guidance for a particular tool’s use and while all attention is given to the accuracy of the data no project should be attempted without referring first to the manufacturer’s technical documentation (workshop or instruction manual) or the use of a recognised authority such as Autodata.
- It is our policy to continually improve our products and thus we reserve the right to alter specifications and components without prior notice. It is the responsibility of the user to ensure the suitability of the tools and information prior to their use.
If this product fails through faulty materials or workmanship, contact our service department direct on: +44 (0) 1926 818186. Normal wear and tear are avchidad as ara cnncimable itame and ablicable
More Info
- Kineton Road, Southam, Warwickshire CV47 0DR
- T +44 (0) 1926 815000
- F +44 (0) 1926 815888
- info@toolconnection.co.uk
- www.toolconnection.co.uk
- www.lasertools.co.uk
FAQ
- Q: What engines is this kit compatible with?
- A: This kit is designed for 1.0 non-turbo Ford Petrol engines.
- Q: Can Laser Tools be held responsible for any damages while using this kit?
- A: Laser Tools recommends using Manufacturer data or Autodata and cannot be held responsible for any damage to the engine or personnel during usage of this tool kit.
Documents / Resources
![]() | 8945 Engine Timing Kit |
References
- Laser Tools | Premier Automotive Hand Tools designed to make easy work of difficult and awkward jobs.www.lasertools.co.uk
- User Manualmanual.tools
Published: April 3, 2025

