LASER 8945 Engine Timing Kit Instruction Manual

Laser-LOGO

Laser 8945 Engine Timing Kit

LASER-8945-Engine-Timing-Kit-PRODUCT

Product Information

  • Part No.: 8945
  • Product: Engine Timing Kit
  • Compatibility: 1.0 Wet Belt Non-Turbo Ford Petrol
  • Manufacturer: Laser Tools
  • Design: UK REGISTERED DESIGN
  • Website: www.lasertools.co.uk

Product Usage Instructions

Flywheel Holding Tool

  • Used to lock the flywheel when loosening and tightening the crankshaft pulley bolt.

Crankshaft Timing Pin

  • Used to set the crankshaft position by turning it clockwise until it contacts the pin.

Tensioner Pulley Locking Pin

  • Locks the belt tensioner in its fully retracted position.

Crankshaft Pulley Alignment Pin

  • Initial position setter for the crankshaft. Remove pin D before torqueing or loosening the crankshaft pulley bolt.

4mm Tensioner Pin

  • Locks the auxiliary belt tensioner in its retracted position.

Camshaft Timing Tools & Fixings

  • Used to lock the camshafts in their timed position independently of their pulleys. Ensure proper assembly over the camshafts and tighten fixing bolts hand tight.

Front Cover Oil Seal Installer

  • Used to fit the new front crankshaft oil seal into the front cover after re-fitting it to the engine. Follow manufacturers tightening sequence and torques for front cover bolts.

Description

  • Designed specifically for the 1.0 litre 3 cylinder normally aspirated petrol engine from Ford, the 7828 kit provides all the tools required to set the engine timing. Our specially designed cam locking bridges offer an easy to use and more positive method of locking the camshaft than even the OEM tools can offer, ensuring the camshafts are securely locked in position  quickly and easily.
  • Applications include: Ford Fiesta (from 2013) 1.0lt Non-Turbo petrol engine codes: P4JA, P4JB, P4JC, P4JD, XMJA, XMJB, XMJC, XMJD and XTCA.
  • For setting of the Variable Camshaft Timing (VCT) units, please use Laser Part No. 6291.
    For Ecoboost Turbo 1.0L engine timing, please see Laser Part No. 6952 (if you already own the Laser timing tool Part No. 6952, the camshaft locking blocks for 1.0L non-turbo are available to buy separately, under part no. 8946).

Use with Laser 7318 and 6291.

  • NOTE*= for 1.0 non-turbo engine only.
  • The information given below is for reference only. Laser Tools recommends the use of Manufacturer data or Autodata. Laser Tools cannot be held responsible for damage to engine or personnel whilst using this tool kit.

Applications

Make Model Year
Ford Fiesta 2013 to 2017

LASER-8945-Engine-Timing-Kit-FIG-1

Engine Codes
1.0LT
P4JA
P4JB
P4JC
P4JD
XMJA
XMJB
XMJC
XMJD
XTCA
Item Comp. No. Description OEM.
A C701 Flywheel Holding Tool 303-1602
B C702 Crankshaft Timing Pin 303-1604
C C282 Tensioner Pulley Locking Pin 303-1054
D C089 Crankshaft Pulley Alignment Pin 303-732
E C488 4mm Tensioner Pin 4MM PIN
F C1070 Camshaft Timing Tools & Fixings 303-1605*
G C705 Front Cover Oil Seal Installer 303-1603

Instructions for use

  • Always refer to manufacturer-specific data and instructions.
  • N.B. the camshaft drive belt on the Ford 3 Cylinder 1.0lt engine is “oil bathed”.
  • The front engine casing must be removed to gain access.
  • Turn engine to TDC number one before disassembly of engine.
  • Remove the starter motor and use component A to hold the flywheel when undoing the crankshaft pulley bolt.LASER-8945-Engine-Timing-Kit-FIG-3

Component A:LASER-8945-Engine-Timing-Kit-FIG-2

  • Used to lock the flywheel when loosening and tightening the crankshaft pulley bolt. Remove the starter motor, assemble component A as shown, and fit in the starter aperture so that its tooth locks the flywheel (see opposite):

Component B:LASER-8945-Engine-Timing-Kit-FIG-4

  • Used to set the crankshaft position. Remove the blanking plug in the side of the engine block as shown and fit component B; turn the crankshaft slowly clockwise until the crankshaft web contacts the end of component B.

Component C:LASER-8945-Engine-Timing-Kit-FIG-5

  • Used to lock the belt tensioner in its fully retracted position, as shown.

Component D:

  • Used to initially set the position of the crankshaft via a hole in the front crankshaft pulley as shown in figure 3.
  • NOTE: Remove pin D in place when torqueing or loosening the crankshaft pulley bolt.

Component E:

  • Used to lock the auxiliary belt tensioner in its retracted position.

Component F:LASER-8945-Engine-Timing-Kit-FIG-6

  • Used to lock the camshafts in their timed position independently of their pulleys. With component B already fitted and the engine at TDC cylinder number 1, assemble the components for F as shown below
  • Install the assembled camshaft components F over the square section of the camshafts ensuring the holding tools seat on the surface of the cylinder head. Fit fixing bolts hand tightLASER-8945-Engine-Timing-Kit-FIG-7
  • N.B. On engines equipped with VCT, if the VCT pulleys require removal or loosening ensure their initial position is marked with chalk or paint. Additional tooling will be required to set the position of the VCT pulleys, see Laser 6291.

Component G:LASER-8945-Engine-Timing-Kit-FIG-8

  • This is used to fit the new front crankshaft oil seal into the front cover after the front cover has been refitted to the engine.

N.B. Always observe the manufacturer’s tightening sequence and torques for the front cover bolts.

  • Our products are designed to be used correctly and with care for the purpose for which they are intended. No liability is accepted by the Tool Connection for incorrect use of any of our products, and the Tool Connection cannot be held responsible for any damage to personnel, property or equipment when using the tools. Incorrect use will also invalidate the warranty.
  • If applicable, the applications database and any instructional information provided has been designed to offer general guidance for a particular tool’s use and while all attention is given to the accuracy of the data no project should be attempted without referring first to the manufacturer’s technical documentation (workshop or instruction manual) or the use of a recognised authority such as Autodata.
  • It is our policy to continually improve our products and thus we reserve the right to alter specifications and components without prior notice. It is the responsibility of the user to ensure the suitability of the tools and information prior to their use.

If this product fails through faulty materials or workmanship, contact our service department direct on: +44 (0) 1926 818186. Normal wear and tear are avchidad as ara cnncimable itame and ablicable

More Info

FAQ

  • Q: What engines is this kit compatible with?
    • A: This kit is designed for 1.0 non-turbo Ford Petrol engines.
  • Q: Can Laser Tools be held responsible for any damages while using this kit?
    • A: Laser Tools recommends using Manufacturer data or Autodata and cannot be held responsible for any damage to the engine or personnel during usage of this tool kit.

Documents / Resources

PDF thumbnail8945 Engine Timing Kit
Instruction Manual · 8945 Engine Timing Kit, 8945, Engine Timing Kit, Timing Kit

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.