Use round cable don’t use flat cable
- The round mains cable should be at least 6mm in diameter.
- Ensure the connection is tightened, to create a good water seal.
- Read in combination with the manual.
- Keep for future reference.
Kingfisher International Products Limited, 3 Sheldon Square, London, W2 13PX, United Kingdom www.kingfisher.corn/products
Wall-mounted lights
Safety
- These instructions are for your safety. Please read through them thoroughly prior to installation and retain them for future reference.
- All fittings must be installed by a competent person in accordance with local regulations (IET wiring regulation BS7671).
- Check the pack and make sure you have all of the parts listed. El Remove all packaging, wrap, etc. from the product.
- Decide on the appropriate location for your product.
- CAUTION: IP44 is guaranteed when the product is properly installed and sealed.
- CAUTION: Adjusting is only possible by means of a tool: Make sure the power supply has been switched off before adjustment. The adjusting screw needs to be firmly fixed incorrect position after adjustment.
- Always avoid the product being located in a corrosive environment. Z Always refer to the installation drawing for the orientation of the product.
- The product must be securely fixed to the mounting surface using the screws and wall plugs supplied. The screws and wall plugs supplied are suitable for ‘masonry” only. Other fixings are not supplied and must be purchased.
- Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation.
- IMPORTANT: The fixing point(s) selected must be capable of supporting the full weight of the light fitting.
- We recommend connecting this product to an external / wall switch in order to deactivate the motion detection function if necessary.
- A wiring diagram is for reference only. Always refer to the terminal marking for wiring. Ensure that all electrical connections are tight and that no loose strands are left out of the terminal block.
- Never put anything on the product or hang anything on any part of this product.
- Never use the terminal cables to bear the product weight. El When the product does not light after installation:
> Ensure there is no electricity failure
> Ensure all the connections are secured - If you have any doubt about the installation/use of this product, consult a qualified electrician.
- Always disconnect the product from mains for at least 10 minutes allowing it to cool down before any maintenance or adjustment. RI It is recommended to have a regular schedule of care and maintenance to keep the surface condition well
Technical Data
| Supply Voltage: | 220-240 V-. 50/60 Hz |
| Bulb Type: | LED (20 W) The light source contained in this luminaire shall only be replaced by a similarly qualified person. Do not stare at the operating light source. |
| Product: Weight: 0.7 kg Dimension: H. 19.5 x W. 17.4 x D. 12.8 cm Max. projected area: 339 cm’ |
|
 |
Conformity with all relevant EC Directive requirements. |
 |
Class I product. must be connected to the earth. |
IP44 |
Splash-proof |
 |
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice. |
 |
product is not suitable for dimming. |
 |
Risk of electric shock! |
|
xxWyy |
xx-year: yy-week of the year |
Warranty Period and Conditions
Guarantee
Congratulations on your purchase of a quality LAP product. We are confident in the quality of this product, but for your peace of mind, it comes with a 3-year guarantee. If your product develops a fault within the guarantee period, please contact the retailer where the item was purchased, with your proof of purchase, where the product will be replaced or refunded.
This guarantee specifically excludes:
- Fair wear and tear
- Misuse or abuse
- Lack of routine maintenance (see care instructions)
- Failure of fixings
- Accidental damage
- Cosmetic damage
- Failure to follow the manufacturer’s fitting/ care and maintenance instructions
This guarantee is limited to the purchase price of the product and the manufacturer’s liability does not extend to any costs damages or losses whatsoever in excess of that amount. Proof of purchase is required. This guarantee does not affect your statutory rights.
Manufacturer: Kingfisher International Products Limited, 3 Sheldon Square, London, W2 6PX, United Kingdom
IMPORTANT –
Please read carefully the separate safety guide before use.
Installation
L = Brown or Red
N = Blue or Black
= Green 1 Yellow
Use
Activate sensor override mode
De-activate sensor override mode
Care
Documents / Resources
 | Wall Mounted Lights |
References
- User Manualmanual.tools
I purchased an LAP L3291S-B (767CC) on 17 May last year (2020).
For the first year or so, it worked very well, but since the start of the summer the light hasn’t worked at all well.
The light is very dim (so much so that it shines next to no light) though it still works.
Any suggestions?
I bought it from Screwfix in Cwmbran, South Wales.
For the first year or so, it worked very well, but since the start of the summer the light hasn't worked at all well.
The light is very dim (so much so that it shines next to no light) though it still works.
Any suggestions?
I bought it from Screwfix in Cwmbran, South Wales.
Why is my LAP L3291S-B (767CC) wall light very dim and how can I fix it?
Based on the manual for the LAP wall-mounted light series, here are the relevant details regarding your issue:
If the light is not on a dimmer and cleaning the lens does not help, the unit likely has an internal fault and should be replaced under warranty.
Read the full Q&A page
Can you wire the light from a 3 pin plug
Can the LAP wall-mounted light be wired using a 3-pin plug?
The manual for the LAP Wall Mounted Light (Model L3292S-B) specifies that it is a Class I product and must be connected to earth. While the instructions primarily illustrate a fixed installation to a mains supply via a wall switch or consumer unit, it is technically possible to wire it to a 3-pin plug provided you follow these safety requirements:
The manual recommends that all fittings be installed by a competent person in accordance with local wiring regulations (such as IET BS7671). If you have any doubt, consult a qualified electrician.
Wiring Color Code:
L (Live) = Brown or Red
N (Neutral) = Blue or Black
Earth = Green / Yellow
Note: Modifying the intended installation method may affect your warranty or the IP44 weather sealing if not done correctly.
Disclosed uncertainty: The manual does not explicitly forbid plug-in use, but it is designed and documented as a fixed-wire luminaire.
Read the full Q&A page
Can you wire the light from a 3 pin plug
Can the LAP wall-mounted light be wired from a 3-pin plug?
Based on the provided instruction manual, this LAP wall-mounted light is designed to be permanently installed and hardwired directly into the mains electrical supply, not powered by a 3-pin plug.
The manual specifies several key points that indicate a hardwired installation:
For safety and to ensure the product functions correctly and maintains its weather-resistant properties, you should follow the manufacturer's installation instructions. If you are unsure, it is highly recommended to consult a qualified electrician.
Read the full Q&A page
thanks for the ins details for my pir lamp,the originals got binned in error,will let you know if my settings work
Algy
Algy
How do I configure the settings for my LAP PIR wall-mounted light?
The LAP Wall Mounted Light (Model L3292S-B) features three adjustable dials on the PIR sensor unit to customize its operation:
Sensor Override Mode:
Note: Adjustments should be made using a tool, and the power should be switched off before making changes to ensure safety.
Read the full Q&A page