LANCOM LX-7300 Exhibiting First Wi-Fi 7 Access Points Instruction Manual

Select 4 suitable pan head screws M4x35 and suitable dowels for mounting on a load-bearing wall.
Mount the retaining plate on the wall using the screws through the marked holes.

Ceiling Mounting:

Select 4 suitable pan head screws M4x35 and suitable dowels for mounting on a load-bearing ceiling.

Mount the retaining plate on the ceiling using the screws through the marked holes.

Connecting Interfaces:

USB 2.0 Interface: Connect compatible USB devices directly or via a USB cable.
TP-Ethernet Interfaces ETH1 / ETH2: Connect to other network components using Ethernet cables.

Device Operation:

Kensington Lock Holder: For mechanical theft protection of the access point.

Reset Button: Press up to 5 seconds for device restart, press longer than 5 seconds for configuration reset and device restart.

Important Notes:

Avoid placing objects on top of the device or stacking multiple devices.
Use lockable wall and ceiling mounting provided with the product.

Refer to the enclosed installation guide for initial startup instructions.
No support for third-party accessories is provided.

FAQ

Q: What do the LED indicators signify?
- A: The LED indicators show different statuses such as device power, operational state, and connectivity like WLAN Link status. Refer to the user manual for detailed LED descriptions.

Overview

USB 2.0 interface
- Connect compatible USB devices to the USB interface either directly or via a suitable USB cable.
Kensington Lock holder
- For mechanical theft protection of the access point
Reset button
- Pressed up to 5 seconds: Device restart
- Pressed longer than 5 seconds:
- Configuration reset and device restart
TP-Ethernet interfaces ETH1 / ETH2
- Connect the ETH1 or ETH2 interfaces to other network components using suitable Ethernet cables.

Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!
Please note that support for third-party accessories is not provided.

Please observe the following when setting up the device

Do not place any objects on the top of the device or stack several devices
Lockable wall and ceiling mounting using the supplied wall mount

Mounting & Connecting

Wall mounting

Depending on the wall material structure, select 4 suitable pan head screws M4x35 ➀ and, if necessary, suitable dowels for mounting the retaining plate ➁ on a sufficiently load-bearing wall.
Mount the retaining plate ➁ with the screws ➀ through the holes marked in the illustration to the wall.
The access point is already prepared for mounting on the mounting plate.

Insert the access point into the mounting plate so that the locking mechanisms on the device and mounting plate are opposite each other and the screws M6x10 ➃ already pre-assembled on the device reach into the keyhole-shaped recesses of the retaining plate. Then push the device towards the locking mechanism up to the stop.
Ensure that the appliance is locked by tightening the locking screw ➂ in the direction of the device and then turn it 90° clockwise.
To remove the device, turn the locking screw ➂ 90° counterclockwise and pull it away from the device. The device can now be removed from the retaining plate in the opposite direction to the locking direction.

Ceiling mounting

Depending on the ceiling material structure, select 4 suitable pan head screws M4x35 ➀ and, if necessary, suitable dowels for mounting the retaining plate ➁ on a sufficiently load-bearing ceiling.

Mount the retaining plate ➁ with the screws ➀ through the holes marked in the illustration to the ceiling.
The access point is already prepared for mounting on the mounting plate.
Insert the access point into the mounting plate so that the locking mechanisms on the device and mounting plate are opposite each other and the screws M6x10 ➃ already pre-assembled on the device reach into the keyhole-shaped recesses of the retaining plate. Then push the device towards the locking mechanism up to the stop.

Ensure that the appliance is locked by tightening the locking screw ➂ in the direction of the device and then turn it 90° clockwise.
To remove the device, turn the locking screw ➂ 90° counterclockwise and pull it away from the device. The device can now be removed from the retaining plate in the opposite direction to the locking direction.

LED Description

*) The additional power LED statuses are displayed in 5-seconds rotation if the device is configured to be managed by the LANCOM Management Cloud.

The product contains separate components which, as so-called open source software, are subject to their own licenses, in particular the General Public License (GPL). The license information for the device firmware (LCOS LX) can be found via the command line with the command „show 3rd-party-licenses“. If required by the respective license, source files for the affected software components are provided on request. For this purpose, please contact us via e-mail at gpl@lancom.de.

Technical Details

More Info

Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with Directives 2014/53/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of Conformity is available at the following Internet address: www.lancom-systems.com/doc

LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and / or omissions.

Documents / Resources

LANCOM LX-7300 Exhibiting First Wi-Fi 7 Access Points [pdf] Instruction Manual
LX-7300 Exhibiting First Wi-Fi 7 Access Points, LX-7300, Exhibiting First Wi-Fi 7 Access Points, First Wi-Fi 7 Access Points, Wi-Fi 7 Access Points, 7 Access Points, Points

References

User Manual

LANCOM LX-7300 Exhibiting First Wi-Fi 7 Access Points

Product Information

Product Usage Instructions

FAQ