U-PROX SE Mini Universal Reader with OSDP User Manual

Interfaces: OSDP, Wiegand 26, 32, 34, 37, 40, 42, 56, 58, 64,
80 bits, RS232, TouchMemory
Connection Cable: Multi-core signal cable with 0.22 mm2
cross-section of each wire

Card Support: RFID 125 kHz, Mifare DESFire EV1, EV2, EV3
cards
Warranty: 2 years (excluding batteries)

Product Usage Instructions

Description

The U-PROX SE MINI is a universal miniature reader with OSDP
capabilities.

Installation

Make a small recess or hole (diameter is 14 mm) to connect the
cable under the reader’s case.

Loosen the screw at the bottom of the reader.
Remove the top cover and back plate.

Mount the back plate on the wall using supplied plastic dowels
and screws.
Carry out wiring to the control panel.

Insert the reader in the back plate.
Place the top cover and tighten it with a screw.

Note: Avoid installation on metal surfaces to
prevent a decrease in reading range.

Connection

The U-PROX SE MINI can be seamlessly connected to existing and
new access systems through various interfaces including OSDP,
Wiegand, RS232, and TouchMemory. Use a multi-core signal cable with
0.22 mm2 cross-section for optimal connection.

Configuration

Adjust the reader using the free mobile application U-Prox
Config. To set the engineering password, connect inputs D0 (green)
and D1 (white) with each other and power the reader. The firmware
can be updated using an NFC-enabled Android smartphone.

Mobile Identification

Utilize the U-PROX ID application to manage mobile credentials
between the reader and smartphone. Mobile IDs can be purchased from
authorized dealers.

RFID, 125 kHz

RIFD cards with 125 kHz frequency are supported. Ensure
encryption for added security. The reader also supports Mifare
DESFire EV1, EV2, EV3 cards with AES encryption algorithm.

Frequently Asked Questions (FAQ)

Q: How long is the warranty for U-PROX devices?

A: The warranty for U-PROX devices (excluding batteries) is
valid for two years from the purchase date. Contact
support@u-prox.systems for assistance.

“`

View Fullscreen

U-PROX SE MINI
Universal miniature reader with OSDP
U-PROX SE MINI USER MANUAL
Description
U-PROX SE mini the adjustable universal SmartLine reader for mobile credentials and proximity identifiers. In conjunction with the U-PROX ID application and mobile identifiers U-PROX IDs allow any access control system to use smartphones as access system credentials.
Installation

1. Make small recess or hole (diameter is 14 mm) to connect cable under the reader’s case
2. Loosen the screw at the bottom of the reader
3. Remove the top cover, remove the back plate 4. Mount the back plate of reader on the wall using supplied plastic dowels and screws 5. Carry out wiring to the control panel 6. Insert the reader in the back plate 7. Place the top cover and tighten it with a screw
Installation on the metal surfaces may cause decrease of reading range. Do not place readers closer than 20 cm one from another. It is possible to install two readers at a distance 10-15 cm of each other when their yellow wires (Hold/Sync) interconnected. This synchronizes the work of the readers, they will work alternately.
Connection

Seamless and easy connection to existing and new access systems, due to the OSDP, Wiegand 26, 32, 34, 37, 40, 42, 56, 58, 64, 80 bits interfaces, Wiegand with automatic selection, RS232 and TouchMemory supports. We recommend to use multi-core signal cable with 0.22 mm2 cross-section of each wire between reader and panel.
Wiegand
The reader connection wires functions are listed in the table.
Wpaenerelcwoimthmtwenisdteeddtpoauirs.e following whiring when reader connected to the control

OSDP
The reader connection wires functions are listed in the table.
Wpaenerelcwoimthmtwenisdteeddtpoauirs.e following whiring when reader connected to the control

RS-232
The reader connection wires functions are listed in the table.
TouchMemory
The reader connection wires functions are listed in the table.

Wpaenerelcwoimthmtwenisdteeddtpoauirs.e following whiring when reader connected to the control
Configuration
With the free mobile application U-Prox Config, the reader can be completely adjusted — from the indication to the encryption modes.

The reader is supplied without the engineering password for programming specified. To connect and (re) set the password — connect inputs D0 (green) and D1 (white) with each other and apply power to the reader.
The reader firmware can be updated with an NFC-enabled Android smartphone only.
Mobile identification
Reader supports digital personal mobile credential. It is processed and stored in the user’s smartphone using the U-PROX ID application. It can be transferred over NFC and/or 2.4 GHz radio between the reader and the smartphone. Reader supports hardware active mobile identifiers U-PROX Tag and U-PROX Auto Tag. Reader supports 3 operation modes for smartphones with U-Prox ID: “Door-Proximity” 10-20 cm, reader activates by built-in proximity sensor. Recommended for doublesided doors and turnstiles “Door” up to 60-70 cm “Barrier/Gate” adjustable range of interaction from 1 to 15 m.
U-PROX ID application
Free mobile application U-PROX ID receives, stores and transmits mobile credentials between the reader and the smartphone.

How to obtain mobile ID
You can purchase mobile IDs from our dealers
RFID, 125 kHz
The reader supports 125 kHz cards with amplitude (ASK EmMarine, etc.) and frequency modulation (FSK Temik, etc.)
These cards do not have cloning protection, but are very popular due to their low cost
Mifare® identifiers
The reader supports work with Mifare® cards, reads encrypted identifiers with a user-assigned card number, with a static or diversified encryption key. Up to five encryption profiles can be used simultaneously.
Mifare®Classic
The least secure series of cards, has a Crypto 1 (SL1) encryption algorithm vulnerability. When using it, it is recommended to encrypt all card sectors with a diversified encryption key.
Mifare®Plus
The reader supports SL1 and SL3 modes for Mifare®Plus. It is recommended to use SL3 mode as it has the highest security and AES encryption algorithm.
Mifare®Defire
The reader supports Mifare DESFire EV1, EV2 and EV3 cards. AES encryption algorithm is supported.
Warranty
Warranty for U-PROX devices (except batteries) is valid for two years after the purchase date. If the device operates incorrectly, please contact support@u-prox.systems at first, maybe it can be solved remotely.

Documents / Resources

U-PROX SE Mini Universal Reader with OSDP [pdf] User Manual
SE Mini Universal Reader with OSDP, Universal Reader with OSDP, Reader with OSDP, with OSDP

References

User Manual